• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.796-804
• /
• 2003

The use of fracture mechanics has traditionally concentrated on crack growth under an opening mechanism. However, many service failures occur from cracks subjected to mixed-mode loading. Hence, it is necessary to evaluate the fatigue behavior under mixed-mode loading. Under mixed-mode loading, not only the fatigue crack propagation rate is of importance, but also the crack propagation direction. In modified range 0.3$\leq$a/W$\leq$0.5, the stress intensity factors (SIFs) of mode I and mode II for the compact tension shear (CTS) specimen were calculated by using elastic finite element analysis. The propagation behavior of the fatigue cracks of cold rolled stainless steels (STS304) under mixed-mode conditions was evaluated by using K$\_$I/ and $_{4}$ (SIFs of mode I and mode II). The maximum tangential stress (MTS) criterion and stress intensity factor were applied to predict the crack propagation direction and the propagation behavior of fatigue cracks.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.276-282
• /
• 2012

This study looked for Mode status of each for fatigue crack growth behavior about the repeat load of mode I and the static load of mode II. The experiment was performed in the state of the repetition frequency of the sine wave 10Hz, the stress ratio 0.1, maximum load 300kg.f, a static load 0, 100, 200, 300kg.f, As the experimental results, in mode of static load, while the load value increases, the crack growth rate is slower as the energy of a crack mixing grows. Mode I and the power mode II get an influence each other in the direction of crack propagation path, but as they eventually get closer to the breaking point of the crack growth, it is dominated by the mode I.

• 전자공학회논문지A
• /
• 제32A권12호
• /
• pp.91-100
• /
• 1995

This paper represents the lateral first-order mode characteristics for the semiconductor laser diodes using a two-dimensional numerical simulator. In order to analyze the lateral first-order mode characteristics, Helmholtz wave equation is solved twice for the lateral fundamental and the first-order mode considering the mode gain, total losses, and the recombination rate due to the stimulated emission radiation for the each mode independantly. Through this procedure, we find that the lateral first-order mode was easily guided as increasing the stripe width for the index-guiding structures, and that the lateral first-order mode seems to be dominated in the distribution of total light intensity when its output power reaches nearly half of that of the lateral fundamental mode. This results may be used to design the device structure which guides only the lateral fundamental mode.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 12th KACG Technical Meeting and the 4th Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.275-280
• /
• 1997

We have investigated the deposition characteristics of (Ni0.8Fe0.2)20Ag80 thin films as a function of chamber pressure and nitrogen flow rate with scanning electron microscopy(SEM), atomic force microscopy(AFM), XRD and $\alpha$-step. The deposition rate of these film is decreased with increasing the chamber pressure and the nitrogen flow rate. With raising the chamber pressure, the growth mode of thin film is changed from island growth to columnar one, which is probably due to energy of atom. Contrary, the nitrogen flow rate is raised, growth mode is changed from columnar to island one. According to the XRD patterns, the preferred orientation is inhibited as the nitrogen flow rate is kept above 10 sccm, but that is nearly independent on the chamber pressure. When the chamber pressure decrease or the nitrogen flow rate increase, phase separation into permoally and silver is occured.

• 제어로봇시스템학회논문지
• /
• 제20권5호
• /
• pp.563-569
• /
• 2014

This article focuses on a hemispherical resonator gyro driven by the Coriolis effect. A hemispherical shell, called a resonator, is maintained in the resonance state by amplitude control and phase locking control. Parametric excitation has been used to control the amplitude. For rate measurement mode or FTR mode, nodal points have been kept to an amplitude of zero. Angular rate measurement has been demonstrated by rotating a resonator. Frequency mismatch between two stiffness principal axes is a major cause of low performance: vibrating pattern drift and reduced control effectiveness. This mismatch has been reduced significantly by the addition of small mass. A negative spring effect, which lowers resonance frequencies, has been verified experimentally.

• 수산해양기술연구
• /
• 제35권4호
• /
• pp.410-420
• /
• 1999

The value of the mode I interlamina fracture toughness, GIC, is calculated by experimental compliance method, modified compliance method and beam theory. The value of the mode II interlamina fracture toughness, GIC, is evaluated by beam method, theory beam theory and compliance method. This paper describes the effect of load pint displacement rate and speicimen geometries for mode I and II interlaminar fracture toughness of glass fiber reinforced plastic composites by using double cantilever beam (DCB) and end notched flexure (ENF) specimen. For the load point displacement rate of increases whereas the value of 2,6 and 10 mm/min the value of GIC decrease as load point displacement rate increases whereas the value of GIC is found to be no significant effect. The value of GIC decreases as initial crack length increases. The fractured surface of the DCB and ENF samples are examined by scanning electron microscopy (SEM).

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.13-16
• /
• 2012

The interaction between methane and hydrogen premixed flames with the different equivalence ratio and global strain rate was investigated numerically in one-dimensional counterflow field. The OPPDIF code and GRI-v3.0 were used to simulate the interacting flames. Overall trends in the maximum heat release rates of $CH_4{^-}$ and $H_2$-side flame were examined with the variation of $a_g$. The interaction mode of the flames were classified according to the equivalence ratios and Lewis numbers of each flame and global strain rate.

• 한국분무공학회지
• /
• 제8권2호
• /
• pp.24-30
• /
• 2003

An experimental study was performed to investigate the influence factors of drop formation in electrohydrodynamic atomization. The mode of electrohydrodynamic atomization depended on the various factors such as the flow rate of the liquid, the inner diameter of the nozzle, the distance between the nozzle tip and the ground electrode, the shape of the ground electrode. and the applied high voltage. This work was performed to investigate the experimental analysis for the flow pattern visualization of droplets, and the relationship between voltage application and the behavior of liquid atomization. Uniform drops of different sizes can be obtained at the inception of the spindle mode by charging the flow rate and the electric field. The drop size also decreased when the flow rate was raised for the spindle mode. The whipping motion occurred beyond 7kV and before the corona started to take effect.

• Journal of the Optical Society of Korea
• /
• 제18권5호
• /
• pp.611-615
• /
• 2014

We report high-speed pulse train generation from a relatively low-speed 10-GHz mode-locked laser by means of line-by-line spectral coding. To increase the pulse repetition rate multiplication (RRM) factor, we combine coding schemes for both spectral intensity and phase by placing a simple mask at the coder focal plane. The resulting RRM factor, determined by multiplying the RRM factors of the individual coding schemes, rises as high as 16. To verify the generated pulses, the optical spectra and autocorrelation traces are examined.

• 전기전자학회논문지
• /
• 제23권1호
• /
• pp.254-260
• /
• 2019

본 논문에서는 양방향 dc-to-dc 컨버터의 고장원인, 고장영향, 고장 결과를 파악하기 위한 failure mode and effect analysis(FMEA)와 양방향 컨버터의 위험도를 고려한 fault-tree analysis(FTA)를 통해 고장률을 예측한다. 전기차의 구동전압을 효율적으로 상승시키기 위해 인버터 앞단에 부착되는 양방향 컨버터는 배터리 전력을 dc-link 커패시터로 방전시키는 승압모드와 회생전력을 배터리로 충전시키는 강압모드를 가진다. 양방향 컨버터의 동작 특성을 고려한 FMEA 결과를 바탕으로 컨버터의 위험도를 고려한 고장나무를 설계한다. 전기차 MCU용에 맞는 설계 파라메타를 설정하고 출력전압 리플과 인덕터 전류 리플에 따른 커패시터와 인덕터의 부품 고장률을 분석한다. 또한 동작 온도에 따른 주요부품의 고장률을 MIL-HDBK-217F를 이용하여 구한다. 마지막으로 부품 고장률을 고장나무의 기본 사상의 고장률로 반영하여 컨버터 고장률과 평균고장시간을 예측한다.