• 한국안전학회지
• /
• 제31권6호
• /
• pp.45-51
• /
• 2016

The purpose of this study is to investigate the influence of train-induced end rotation of simple supported track girder on the performance of a direct fixation track system (DFTS) in Yeongjong grand bridge. In this study, the influences of deflection of a DFTS and track girder on dynamic rail-track girder interaction forces for the track girder ends currently employed in airport express lines were assessed by performing field tests using actual vehicles running along the service lines. Therefore, the dynamic displacement of rail and track girder and the fastener stress on the center and ends sections of DFTS were measured for two different trains (AREX and KTX) running in Yeongjong grand bridge. A three-dimensional finite element analysis (FEA) model using the time-history function based on the design wheel load was used to predict the train-induced track and track girder displacement, and the FEA and field test results were compared. The analytical results reproduced the experimental results well within about 3-7% difference in the values. Therefore, the FEA model of DFTS on track girder is considered to provide sufficiently reliable FEA results in the investigation of the behavior of DFTS. Using the analytical and experimental results, the influence of train-induced end rotation of simple supported track girder on the interaction behavior of rail and track girder installed on a simple supported track girder ends, i.e., upward displacement of rail-track girder and the fastener stress, was investigated. It was found that the train-induced end rotation effect of track girder was not significantly affected by the upward displacement of rails and the fastener stresses of track girder ends. Further, the interaction behavior of rail and track girder were similar to or less than that of the general railway bridge deck ends, nevertheless the vertical displacement of track was higher than that of conventional DFTS on the general railway bridge. From the results, the dynamic responses of the DFTS on track girder ends were not significantly affected by the safety and stability of DFTS ends.

• 한국철도학회논문집
• /
• 제17권4호
• /
• pp.245-250
• /
• 2014

본 연구에서는 콘크리트 궤도 교량의 사용성 설계를 위한 연구로서 궤도 및 교량 설계변수들이 콘크리트 궤도의 레일지지점에서의 작용력에 미치는 영향을 나타내었다. 궤도 구조에 작용하는 작용력을 구하기 위해서 각 레일 지지점의 간격이 다른 부등간격 이산지지보 모델을 유도하였다. 해석 변수는 교량의 교대 또는 교각 위치 부근의 신축이음부의 레일 지지점의 간격, 교량 거더의 받침에서부터 교량 거더 단부측의 마지막 레일지 지점까지의 거리, 그리고 추가 배치한 레일지지점의 수이다. 궤도 구조의 변위를 일으키는 요인으로는 축하중, 거더의 단위 수직단차와 단부회전각이다. 해석결과로부터 레일지지점에서의 최대압축력과 최대부상력을 구하였으며 레일지지점의 간격이 작용력에 미치는 영향을 나타내었다.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1617-1630
• /
• 2018

The crucial differences between conventional rail with split-type connectors and continuous welded rails are axial stress in the longitudinal direction and stability, as well as other issues generated under the influence of loading effects. Longitudinal stresses generated in continuously welded rails on railway bridges are strongly influenced by the nonlinear behavior of the supporting system comprising sleepers and ballasts. Thus, the track structure interaction cannot be neglected. The rail-support system mentioned above has properties of non-uniform material distribution and uncertainty of construction quality. The linear elastic hypothesis therefore cannot correctly evaluate the stress distribution within the rails. The aim of this study is to apply the nonlinear finite element method using the nonlinear coupling interface between the track and structural model and to illustrate the welded rail behavior under the loading effect and uncertain factors of the ballast. Numerical results of nonlinear finite analysis with a three-dimensional solid and frame element model are presented for a typical track-bridge system. A composite plate girder, modeled by solid and shell elements, is also analyzed to consider the behavior of the welded rail. The analysis result showed buckling under the independent calculations of load cases, including 'temperature change', 'bending of the supporting structure', and 'braking' of the railway vehicle. A parametric study of the load combination method and the loading sequence is also included in this analysis.

• 한국전산구조공학회논문집
• /
• 제29권2호
• /
• pp.169-177
• /
• 2016

슬라이딩 궤도는 콘크리트 궤도와 교량 바닥판 사이에 저마찰 슬라이드층을 두어 레일신축이음장치와 같은 특수 장치를 적용하지 않고도 궤도-교량 상호작용 효과를 효과적으로 저감시킬 수 있는 새로운 궤도 시스템으로 개발되고 있다. 이 논문에서는 장경간 교량에 슬라이딩 궤도와 레일신축이음장치를 각각 적용한 경우에 대하여 궤도-교량 상호작용해석을 수행하고 그 결과를 비교 검토하였다. 대상교량은 상호작용 효과를 극대화하기 위하여 9경간 연속 PSC교와 2경간 연속 강합성교를 포함하며, 총 연장 1,205m, 최대 고정지점간 거리 825m인 장경간 교량을 선정하였다. 해석결과 슬라이딩 궤도는 레일신축이음장치를 적용한 경우보다 레일 부가 축력이 더 작은 것은 물론, 지점부에 재하되는 수평 반력 또한 작게 나타나 궤도-교량 상호작용 저감 효과가 뛰어난 것으로 확인되었다. 반면 슬라이딩 궤도는 온도하중에 의해 높은 슬래브 축력이 발생되므로, 궤도 설계 시 슬래브 축력에 대한 단면 설계에 주의를 기울일 필요가 있다.

• 한국도시철도학회논문집
• /
• 제6권4호
• /
• pp.327-337
• /
• 2018

무도상 판형교는 교량 바닥판과 도상 없이 주거더에 궤도가 직접 연결되어 있는 구조로 열차 통과로 인하여 발생한 충격이 교량 주부재에 직접 전달되어 높은 수준의 소음 진동 뿐 아니라 교량의 잦은 손상을 유발하는 특성이 있다. 레일 장대화는 무도상 판형교의 이러한 구조적인 문제를 경감할 수 있으며, 이를 위해서는 차량-궤도 또는 궤도-교량 상호작용에 영향을 미치는 인자의 특성에 대한 명확한 이해가 필요하다. 이 연구에서는 레일체결장치, 침목고정장치 및 궤광을 포함한 실제 무도상 판형교에 설치되어 있는 궤도의 종방향 저항력 특성을 실험을 통하여 검토하였다. 실험은 유도상화 시공을 위하여 철거된 실제 교량을 실험실로 이송하여 수행하였다. 실험 결과 목침목용 레일체결장치의 종방향저항력은 KRS TR 0014-15의 성능합격기준을 만족하며, 교량침목고정장치의 종방향 저항력은 구형과 신형 모두 기존 연구보다 높은 값으로 나타났다. 또한 하중 비재하 시 무도상 궤도의 종방향 저항력은 자갈궤도와 콘크리트궤도 사이의 값으로 나타났다.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.1469-1476
• /
• 2015

산지가 전국토의 70%를 차지하는 국내 지형의 특성으로 인하여, 철도선로 전체 노선의 상당부분을 교량구간이 차지한다. 이에 따라 교량 설계 시 경제성 증가를 위하여 경간장을 늘리는 것이 유리하지만 궤도-교량 상호작용에 의한 레일의 부가축응력, 변위 등의 문제로 인한 제약이 발생한다. 본 연구에서는 궤도와 교량 상판 사이에 설치되는 슬라이딩 층을 고려한 궤도-교량 상호작용 해석을 수행하였다. 수치해석 결과를 통해 슬라이딩층 설치 방법에 따른 상호작용 거동을 분석하였으며, 궤도-교량 상호작용이 저감된 새로운 궤도-교량 구조시스템의 개발방향을 제안하였다.

• Structural Engineering and Mechanics
• /
• 제54권5호
• /
• pp.1017-1044
• /
• 2015

This study aimed to investigate the random vibration characteristic of train-slab track-bridge interaction system subjected to both track irregularities and earthquakes by use of pseudo-excitation method (PEM). Each vehicle subsystem was modeled by multibody dynamics. A three-dimensional rail-slab- girder-pier finite element model was created to simulate slab track and bridge subsystem. The equations of motion for the entire system were established based on the constraint condition of no jump between wheel and rail. The random load vectors of equations of motion were formulated by transforming track irregularities and seismic accelerations into a series of deterministic pseudo-excitations according to their respective power spectral density (PSD) functions by means of PEM. The time-dependent PSDs of random vibration responses of the system were obtained by step-by-step integration method, and the corresponding extreme values were estimated based on the first-passage failure criterion. As a case study, an ICE3 high-speed train passing a fifteen-span simply supported girder bridge simultaneously excited by track irregularities and earthquakes is presented. The evaluated extreme values and the PSD characteristic of the random vibration responses of bridge and train are analyzed, and the influences of train speed and track irregularities (without earthquakes) on the random vibration characteristic of bridge and train are discussed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.356-363
• /
• 2003

The CWR of the plate girder bridges in non-ballast causes the additional axial force on the rail and the bearing due to the temperature axial force and the interaction between the CWR and bridges. This study shows the remarkable improvement of reducing the axial force of the CWR on the non-ballast bridge, compared to conventional methods. New method, which is differently designed in terms of longitudinal semi-rigid bearing, reduces the axial force on the bearing by making the girder act both directions. This method is applicable to most cases of bridges regardless of the restriction of length, and useful to reduce the abrasion and damage of the track material.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.680-689
• /
• 2011

A dynamic analysis procedure is developed to provide a comprehensive estimation of the dynamic response spectrum for locomotive's wheels running over a Pre-Stressed Concrete (PSC) box girder bridge on the Korea high speed railway. The wheel force spectrum with the bridge behavior are analyzed as the dynamic procedure for various running speeds (50~450km/h). The high-speed railway locomotive (KTX) is used as 38-degree of freedom system. Three displacements(vertical, lateral, and longitudinal) and three rotational components (pitching, rolling, and yawing). For one car-body and two bogies as well as five movements except pitching rotation components for four wheel axes forces are considered in the 38-degree of freedom model. Three dimensional frame element is used to model of the PSC box girder bridges, simply supported span length of 40m. The irregulation of rail-way is derived using the exponential spectrum density function under assumption of twelve level tracks conditions based on the normal probability procedure. The dynamic responses of bridge passing through the railway locomotive with high-speed analyzed by Newmark-${\beta}$ method and Runge-Kutta method are compared and contrasted considering the developed models of bridge, track and locomotive comprehensively. The dynamic analyses of wheel forces by Runge-Kutta method which are able to analyze the forces with high frequency running on the bridge and ground rail-way are conducted. Additionally, wheel forces spectrum and three rotational components of vehicle body for three typical running speeds is also presented.

• Interaction and multiscale mechanics
• /
• 제3권4호
• /
• pp.333-342
• /
• 2010

The Pseudo-Excitation Method (PEM) is applied to study the stochastic space vibration responses of train-bridge coupling system. Each vehicle is modeled as a four-wheel mass-spring-damper system with two layers of suspension system possessing 15 degrees-of- freedom. The bridge is modeled as a spatial beam element, and the track irregularity is assumed to be a uniform random process. The motion equations of the vehicle system are established based on the d'Alembertian principle, and the motion equations of the bridge system are established based on the Hamilton variational principle. Separate iteration is applied in the solution of equations. Comparisons with the Monte Carlo simulations show the effectiveness and satisfactory accuracy of the proposed method. The PSD of the 3-span simply-supported girder bridge responses, vehicle responses and wheel/rail forces are obtained. Based on the $3{\sigma}$ rule for Gaussian stochastic processes, the maximum responses of the coupling system are suggested.