• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.115-124
• /
• 2004

This paper proposes a high efficient and low power FIR filter chip for partial-response maximum likelihood (PRML) disk drive read channels; it is a 6-bit, 8-tap digital FIR filter. The proposed filter employs a parallel processing architecture and consists of 4 pipeline stages. It uses the modified Booth algorithm for multiplication and compressor logic for addition. CMOS pass-transistor logic is used for low power consumption and single-rail logic is used to reduce the chip area. The proposed filter is actually implemented and the chip dissipates 120mV at 100MHz, uses a 3.3V power supply and occupies 1.88 ${\times}$ 1.38 $\textrm{mm}^2$. The implemented filter requires approximately 11.7% less power compared with the existing architectures that use the similar technology.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2_spc
• /
• pp.275-289
• /
• 2020

In 2017, multimodal transportation tests for evaluating road, sea, and rail transport were performed by research institutes in the US, Spain, and the Republic of Korea. In this study, acceleration and strain data determined through road and sea tests were analyzed. It was investigated whether the load generated for each transport mode was amplified or attenuated according to the load transfer path. From the results, it was confirmed that the load transfer characteristics differed according to the transportation mode and loading path. The effects of strain determined through each test on the structural integrity of the spent nuclear fuel were also investigated. It was found that the magnitude of the measured strain had a negligible effect on the structural integrity of the spent nuclear fuel, considering its fatigue strength. The results for the acceleration and strain data analyses obtained in this study will be useful for scheduled domestic transportation tests under normal transport conditions.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.29-38
• /
• 2015

In this study, track dynamic interaction characteristics caused by the vehicle running through transitional section such as bridge abutments were studied using the finite element analysis program. The geometric condition of track was generated by trigonometric function and allowable maximum track irregularity is determined by KORAIL track maintenance criteria. The sub-infrastructure under rail fastener system was modelled by 3D solid elements. To reduce computational cost only half track line is numerically considered and the roller boundary condition was applied to each side of model. In this study, the vehicle-track dynamic interaction analysis was carried out for standard Korean transition section of concrete track and the dynamic behaviors were investigated. The dynamic characteristics considered are wheel load variation, vertical acceleration at body, and maximum Mises stress at each part of transitional section.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.11
• /
• pp.37-49
• /
• 2019

In order to analyze the effect of burial depth on the generation of ground cavities and cave-ins, a series of model experiments with different height of model ground were performed. Digital images of the model ground were captured to evaluate the internal deformation of the model grounds by adopting the PIV (Particle Image Velocimetry) technique. Additionally, the vertical displacement at the surface, the size of the cavity, and the weight of the discharged soil were measured in each test. The results indicate that the model ground with low burial depth, which does not satisfy the criterion, was more vulnerable to ground cavities and cave-ins than the model ground with high burial depth.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.1
• /
• pp.195-202
• /
• 2014

The newly updated Rail Safety Act is required to build a comprehensive railway safety management system with corresponding accreditation regulations for the purpose of safe railway operations. However, such efforts would not be enough to achieve a successful safety-performance solely without being in place of an appropriate level of safety cultures in an organization. No research was taken place to propose a safety culture maturity model and its estimate procedures in Korean railway industries. The research reviews a variety of safety maturity models applied in many other industries and the process of conducting surveys in order to propose a framework of railway safety maturity estimates, with a set of railway safety elements. This research is expected to contribute in diagnosing weak areas and finding their appropriate treatment, along with in placing the railway safety certificate program from 2014.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.5
• /
• pp.445-454
• /
• 2020

Non-breakaway crashworthy sliding posts move rigidly with a vehicle in the early stage of vehicle impact. During this stage, a vehicle imparts its linear momentum to the post, experiencing first-stage speed loss followed by second-stage loss from the crush of the energy-absorbing pipe (EAP) installed under the guide rail. An EAP is the key element of a crashworthy sliding post and should be confined to the post foundation. This paper covers the development of an EAP for a sliding post of 507 kg, which is a sliding post type frequently used in Korea for cantilever signs. Detailed explanations of the designs for an EAP structure using LS-DYNA impact simulation are given, and the crashworthiness of the systems are confirmed through crash tests. The EAP presented in this paper can accommodate impacts from 0.9 ton-60 km/h to 1.3 ton-80 km/h, and is applicable to foundations up to 2.7 m in length.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.173-181
• /
• 2007

Recently, galvanizing method is predominantly being used not only a economical point of view but also due to it s stability and long life. For example, guard rail of high way, all kinds of structures for ship etc. were protected with galvanizing and demand of galvanized structural materials was being increased with more and more. However, galvanized structures were inevitably being deteriorated with time eventually because they were corroded with solution of galvanizing film and exfoliation of it s film in the present severe corrosive environment. Therefore, it is necessary to improve the corrosion resistance of the galvanizing film through various methods such as variation of chemical composition of galvanizing bath, chromate treatment and coating treatment. In this study, three test specimens such as pure galvanizing, galvarium, and chromate treatment were submerged at tap water with inhibitor addition. And the effect of their corrosion resistance improvement was comparatively investigated with electrochemical method. Corrosion current density of the galvanized steel was the largest among three specimens, however, the galvarium steel showed the lowest corrosion current density. Futhermore, these three kinds of test specimens indicated considerably excellent corrosion resistance by dipped at tap water with inhibitor addition. Especially, the galvanized steel showed the best effect of corrosion resistance improvement than other test specimens.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.285-291
• /
• 2015

A centrifuge works on the principle that particles with different densities will separate at a rate proportional to the centrifugal force during high-speed rotation. Dense particles are quickly precipitated, and particles with relatively smaller densities are precipitated more slowly. A decanter-type centrifuge is used to remove, concentrate, and dehydrate sludge in a water treatment process. This is a core technology for measuring the sludge conveyance efficiency improvement. In this study, a smoothed particle hydro-dynamic analysis was performed for a decanter centrifuge used to convey sludge to evaluate the efficiency improvement. This analysis was applied to both the original centrifugal model and the design change model, which was a ball-plate rail model, to evaluate the sludge transfer efficiency.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.4
• /
• pp.91-98
• /
• 2011

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of mounting a quill system to lubricate cylinder parts for smoother operation. In order to apply the common-rail lubricating system to the developed cylinder lubricator as the second research stage, the quill system with a progressively quantitative distributor is improved in the electronically controlled quill system with an accumulating distributor. In this study, the effects of lubricator motor speed, plunger stroke and cylinder back pressure on oil feed rate, maximum discharge and delivery pressures are experimentally investigated by using the electronically controlled quill system with an accumulating distributor in the developed cylinder lubricator. It is found that the oil feed rate of the electronically controlled quill system with an accumulating distributor is larger than that of the quill system with a progressively quantitative distributor because of the increase of delivery speed and volume by changing the location of accumulator in the same experimental condition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.26-36
• /
• 2012

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of mounting a quill system to lubricate cylinder parts for a smooth operation. In order to apply the common-rail lubricating system to the developed cylinder lubricator as the second research stage, the mechanical quill system with a progressively quantitative distributor (M.D.S.) is improved in the electronically controlled quill system with an accumulating distributor (E.D.S.). In this study, the effects of lubricator motor speed, plunger stroke and cylinder back pressure on oil feed rate and inequality rate are experimentally investigated by applying E.D.S. to the developed cylinder lubricator. It is found that the oil feed rate of E.D.S. is higher than that of M.D.S. because of the increase of delivery speed and volume by changing the role of accumulator in the same experimental condition. It can be also shown that, in E.D.S., the inequality rate is decreased a little or hardly unchanged as the cylinder back pressure and plunger stroke is elevated, while the inequality rate increased in M.D.S.. The inequality rates of E.D.S. and M.D.S. are lowered as the lubricator motor speed is increased.