• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.38-42
• /
• 2001

This paper describes an application of the on line partial discharge measurement method in operating transformer. In the operating transformer, the partial discharge signal may be superimposed by radio intereference voltage(RIV) and pulse shaped noise signals generated by external corona. The partial discharge quantity showed about 3,800pC due to very high sinusoidal interferences at the measuring impedance terminal of the transformer bushing tap. In order to reject these noises, this paper applied RIV filter, band-pass filters and noise gating method. The resulting measuring sensitivity was improved from 3,800pC to 160pC.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.289-293
• /
• 2004

In this paper, data rate of VDSL system was analyzed in RFI(Radio Frequency Interference) environment. This Paper used Various 'VDSL Test Loop' suggested by ANSI DSL Standard group TIE1.4.Many parameters, 'Noise Model A', 'Noise Model F' and KARL-HAM band are used for more accurate results of the simulation. Most of conditions for simulation are followed to the ANSI Standard 'Spectrum management'. Many results have been calculated according to the different conditions of the test loops in simulation. Simulation results confirm that using shaped PSD mask to reject RFI is one of factor to decrease the performance of VDSL systems.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.654-656
• /
• 2001

This research used triac that is semi-conductor that act to static contact to overcome happened shortcoming been using mechanical centrifugal force switch usually Detect starting current of single phase induction motor and decided moving time. Therefore, could improve life of switch semipermanently. Also, wish to reduced impact that electric motor suffers at the starting moment and do stable starting which there is no life improvement and noise of electric motor itself, arc.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.5
• /
• pp.1097-1106
• /
• 1997

Most works on importance sampling (IS) as an efficient evaluation technique havd been done in an additibe white gaussian noise channel (Awgn). In this paper we propose a CQ(conventional importance sampling and quasi-translantion) IS technique for the mobile radio channel modeled as Rician fading, and analyze the IS estimator's variance to determine optimum IS parameters and the minimum number of run times. Reference showed that CIS technique has a poor performance for systems with meories, but it is shown that the CIS technique can be improved by combining with quasi-translation technique even for systems with memories. Here the CQ IS technique modifies the variance of additive noise and also performs quasi-translation for the fading distribution. We determine the optimum IS parameters of the proposed CQ IS estimator and whow that the simulation gains are about 10$^{3}$~10$^{6}$ for the mobile communication systems with memories in case of the expected BERs 10$^{-5}$ ~10$^{-8}$ .

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.894-897
• /
• 2003

Recently, the rapid growth of mobile radio system has led to an increasing demand of low-cost high performance communication IC's. In this paper, we have designed RF front end for wireless LAN receiver employ zero-IF architecture. A low-noise amplifier (LNA) and double-balanced mixer is included in a front end. The zero-IF architecture is easy to integrate and good for low power consumption, so that is coincided to requirement of wireless LAN. But the zero-IF architecture has a serious problem of large offset. Image-reject mixer is a good structure to solve offset problem. Using offset compensation circuit is good structure, too. The front end is implemented in 0.25 ${\mu}m$ CMOS technology. The front end has a noise figure of 5.6 dB, a power consumption of 16 mW and total gain of 22 dB.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.7
• /
• pp.71-78
• /
• 2019

This paper describes a design for a RF receiver to receive satellite digital audio service. The RF receiver designed in this study is a planar structure that is easy to install on the rooftop of a car and is compact in size. In addition, it can be applied to certain commercial models because it has low noise and high gain characteristics. The impedance bandwidth of antenna is 17.8%(415MHz), and the axial ratio is below 3dB as good properties for the bandwidth of 40MHz which is a satellite digital audio service band. Also, it had a broad radiation beamwidth of $95.41^{\circ}$ in H-plane and $117.45^{\circ}$ in E-plane. From the results of the field test of satellite digital audio service reception for the RF receiver, it demonstrated good C/N rate(10.2dB).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.436-447
• /
• 2013

In this paper, Integrated circuit(IC) electromagnetic(EM) conducted immunity measurement and simulation using bulk current injection(BCI) and direct power injection(DPI) methods were conducted for 1.8 V I/O buffers. Using the equivalent circuit models developed for IC electromagnetic conducted immunity tests, we investigated the reliability of the frequency region where IC electromagnetic conducted immunity test is performed. The insertion loss for the noise injection path obtained from the simulation indicates that using only one conducted immunity test method cannot provide reliable conducted immunity test for broadband noise. Based on the forward power results, we analyzed the actual amount of EM noise injected to IC. We propose a more reliable immunity test methods for broad band noise.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.4
• /
• pp.292-299
• /
• 2012

The line-of-sight(LOS) rate is estimated using Kalman filter in Radio-Frequency(RF) seeker. For the two axis gimbaled seeker, proper system modeling is considered and the basic filter structure is set up. The main issue for Kalman filter is choosing the proper process and measurement noise. For the measurement process, the signal to noise ratio(SNR) and other components are introduced. To cope with the eclipse problem or other abnormal seeker status, the pseudo input signal concept is proposed. By conditioning abnormal signals, the LOS rate estimation performance is increased. The process noise is also an important factor in the propagation phase. The analytical approach on a process noise component is performed and a reliable region for the filter is calculated based on the eigenvalue analysis. Some numerical simulations are performed to check the validity of suggested algorithm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.8 no.2
• /
• pp.63-75
• /
• 1983

This paper has investigated and discussed the effects of multiple PSK signals upon an wideband FM signal in an intersystem interference environment between analog and digital radios. Using the derived approximate equation for the output haseband interference noise, the signal-to-interference noise power ratio(SNR) in the top channel baseband signal has been numerically calculated. The results are plotted in graphs as the functions of carrier-to-noise ratio(CNR), carrier-to interfer power ratio(CIR), and normalized carrier separation. From the results in this paper, one can know some optimu, or suitable, operating conditions(frequency allocation, bandwidth, and power, etc.) for an FM channel in the intersystemn interferences from digital PSK channels.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.3
• /
• pp.158-163
• /
• 2009

LMS(Least Mean Square) algorithm requires simple equation and is used widely because of the low complexity. If the convergence speed increase, LMS algorithm has a divergence in case of sharp environment changes. And if a stability increase, the convergence speed becomes slow. This algorithm based on a trade off between fast convergence and system stability. To improve this problem, VSSLMS (Variable Step Size LMS) algorithm was developed. The VSSLMS algorithm improved the convergence speed and performance as adjusting step size using error signal. In this paper, I-VSSLMS algorithm is proposed tor improve the performance of adaptive noise canceller in real-time environments. The proposed algorithm is applied to adaptive noise canceller using TMS320C6713 DSP board and we did simulation by real time. Then we compared performance of each algorithm and demonstrated that proposed algorithm has superior performance.