• 한국전산유체공학회지
• /
• 제16권3호
• /
• pp.88-94
• /
• 2011

The availability of the thermal energy has been deeply recognized recently to encourage the cascade usage of thermal energy from combustion. Within the framework, a 1 kW class Stirling engine based cogeneration system has been proposed for a unit of a distributed energy system. The capacity has been designed to be adequate for the domestic usage, which requires high compactness as well as low emission and noise. To develop a highly efficient system with satisfying these requirements, a premixed slot type short flame burner has been proposed and a series of numerical simulation has been performed to establish a design tool for the combustion chamber. The thermal radiation model has been found to highly affect the computational results and a proper resolution to analyze the heat transfer characteristics of the high temperature heat exchanger. Finally, the combustion characteristics of the premixed flame with the metal fiber type burner has been studied.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.618-623
• /
• 2001

In a practical vibration isolation system, vibration is transmitted from the source to the receiver through several paths such as more than one inter-connected point and multi-degree of freedom at each connection point. Therefore, the major path investigation for vibration transmission among them is often required in a point of view of isolation. For the path analysis of multi-dimensional vibration isolation system, it is useful to employ the concept of vibration power in high frequency range where radiation of noise from the receiver structure is concerned. The idea is simple to understand and formulate but rather complicated to apply in practice. For an accurate estimation of power flow especially over a high frequency range, it is well known in theory that rotational motions should be taken into consideration together with translational motions at inter-connected points. In reality, however, power transmissions related to rotational terms are often neglected mainly due to difficulties in the instrumentation. In this paper, necessary formula and measurable mechanical quantities for vibration power analysis will be reviewed and experimental results with rotational terms included for compressor system in a commercial air conditioner will be shown.

• Journal of the Optical Society of Korea
• /
• 제18권1호
• /
• pp.60-64
• /
• 2014

We report the generation of 3.3-mW single-cycle terahertz (THz) pulses at 1-kHz repetition rate via optical rectification in MgO-doped prism-cut stoichiometric LiNbO3. Efficient pulse-front tilting of 800-nm pulses was realized by an optimized single-lens focusing scheme for radially-symmetric propagation of THz beams. In this geometry, nearly-diffraction-limited THz Gaussian beams with electric field strength as high as 350 kV/cm were generated. The pump-to-THz energy conversion efficiency of $1.36{\times}10^{-3}$ and the extremely high signal-to-noise ratio of ~1:15000 achieved are among the best results for 1-kHz single-cycle terahertz pulse generation ever demonstrated in room temperature operation.

• 대한안전경영과학회지
• /
• 제16권2호
• /
• pp.81-90
• /
• 2014

Flexible production system has been expanded to all sectors of economy with the change of labor market and diversification of employment. The unstable employment with irregular work has replaced stable employment with regular work. This study has investigate the impact pathway of the type of employment on health status especially ill-health symptoms experiences. Among the first Korean Working Conditions Survey data, the employee's response data was used to analyze the path way with multiple regression analysis. The result has shown the direct effect of the type of employment on ill-health symptoms experience. Indirect effect of the type of employment was found the pathway via the exposure to noise, high temperature, low temperature, dust, skin contact to chemicals, painful posture, heavy material handling, standing position, repetitive movement of hands. However the exposure to the other hazardous factors such as organic solvent, wholebody vibration, radiation, lifting people, infectious materials were not influenced by the type of employment.

• Nuclear Engineering and Technology
• /
• 제49권4호
• /
• pp.810-816
• /
• 2017

A graphite calorimetry system was built and tested under irradiation. The noise level of the temperature measurement system was approximately 0.08 mK (peak to peak). The temperature of the core part rose by approximately 8.6 mK at 800 MU (monitor unit) for 6-MV X-ray beams, and it increased as X-ray energy increased. The temperature rise showed less spread when it was normalized to the accumulated charge, as measured by an external monitoring chamber. The radiation energy absorbed by the core part was determined to have values of $0.798J/{\mu}C$, $0.389J/{\mu}C$, and $0.352J/{\mu}C$ at 6 MV, 10 MV, and 18 MV, respectively. These values were so consistent among repeated runs that their coefficient of variance was less than 0.15%.

• 한국산업정보학회논문지
• /
• 제4권2호
• /
• pp.32-38
• /
• 1999

본 연구에서는 토목공사에서 필요한 성토시공관리용 방사성 동위원소 이용계기의 전자회로를 개발하고자 하였다. 제작된 계기는 국내 원자력법에서 제한하는 세기 이하의 밀봉선원을 사용하며, 감마선과 열중성자 검출회로, 고전압 공급장치 그리고 마이크로프로세서 등으로 구성하였다. 성토의 밀도측정에 충분한 계측수를 얻기 위하여 감마선 검출은 5개의 회로로, 열중성자 검출은 2개의 회로로 구성하였으며, 또한, 모든 회로는 자연 방사선과 잡음에 의한 영향을 최소화하기 위하여 정전차폐하였으며, 계수관에 인가하는 고전압의 리플 진폭과 주파수를 고려하여 펄스 계수시에 리플 성분에 의한 펄스수는 제거하였다. 방사선의계수 및 연산처리에는 원칩 마이크로프로세서를 이용하였으며, 계측결과는 메모리장치에 저장되었다. 시제작한 RI계기의 검출성능을 평가한 결과 성토의 밀도측정에 충분한 계측수를 얻을 수 있음이 확인되었다.

• 한국통신학회논문지
• /
• 제40권3호
• /
• pp.595-601
• /
• 2015

These days, research related to Intelligent Transportation System (ITS) technology is being widely considered. ITS is inevitable for future transportation systems to reduce accidents, congestion, and offer a smooth flow of traffic. The use of Visible Light Communication (VLC) in ITS systems has been considered widely because of its EMC/EMI free and LED infrastructure reusable properties. Among the VLC schemes, this study analyzed the performance of the Color Shift Keying (CSK) scheme under a Vehicle-to-Infrastructure (V2I) downlink scenario to verify the capability of CSK as a communication tool for ITS. By modeling daylight noise using the modified Blackbody radiation model, this study examined the performance of V2I VLC under daytime conditions. The relationship between BER, the communication distance, and the amount of ambient-light noises under the pre-described V2I scenario were determined by simulations.

• 한국위성정보통신학회논문지
• /
• 제1권1호
• /
• pp.54-58
• /
• 2006

동작주파수를 쉽게 조절할 수 있는 신호생성용 안테나 (Antenna-Integrated Oscillator) 설계방법을 소개한다. 제안하는 회로는 광대역에서 부성저항을 갖는 능동회로 (Negative-Resistance Circuit)와 패치안테나로 구분되며, 오실레이터의 동작주파수는 안테나의 공진 주파수로 결정된다. 이러한 디자인 방법은 안테나와 오실레이터의 동작주파수 불일치로 인한 출력파워의 감소 가능성을 줄일 수 있다. 또, 제안하는 설계방법에서 안테나의 Feed 지점과 Feed 라인의 길이를 조절하여 최적의 출력파워를 낼 수 있음을 Load-Pull 시뮬레이션으로 확인하였다. C-band, X-band 회로를 각각 제작, 측정하였고 이를 통하여 설계방법의 타당성을 증명하였다.

• 한국정보통신학회논문지
• /
• 제5권4호
• /
• pp.807-811
• /
• 2001

파수 원형 섹터 마이크로스트립 안테나를 제안하였다 그리고 이것을 사용하여 5.6 GHz 에서 송신과 5.5 GHz 에서 수신 동작을 하는 트랜시버를 제작하였다. 트랜시버의 송수신 주파수 분리에 제안된 안테나의 좋은 격리도 특성을 이용하였다. 제안한 이중 주파수 안테나의 동작 주파수 및 편파 특성을 공진기 모델을 사용하여 계산하였으며, 안테나의 S 파라미터 및 복사패턴을 측정하였다. 전력증폭기 및 저잡음 증폭기를 설계하여 안테나와 집적하여, 송신 및 수신 이득이 각각 약 13dB 및 약 8dB가 되는 트랜시버를 제작하였다.

• 전기학회논문지P
• /
• 제65권3호
• /
• pp.158-164
• /
• 2016

In this paper, a high frequency flyback type zero voltage soft switching PWM DC-DC converter using IGBTs is proposed. Effective applications for this power converter can be found in auxiliary power supplies of rolling stock transportation and electric vehicles. This power converter is basically composed of active power switches and a flyback high frequency transformer. In addition to these, passive lossless snubbers with power regeneration loops for energy recovery, consisting of a three winding auxiliary high frequency transformer, auxiliary capacitors and diodes are introduced to achieve zero voltage soft switching from light to full load conditions. Furthermore, this power converter has some advantages such as low cost circuit configuration, simple control scheme and high efficiency. Its operating principle is described and to determine circuit parameters, some practical design considerations are discussed. The effectiveness of the proposed power converter is evaluated and compared with the hard switching PWM DC-DC converter from an experimental point of view and the comparative electromagnetic conduction and radiation noise characteristics of both DC-DC power converter circuits are also depicted.