• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.410-414
• /
• 1996

기존의 초고압 옥외절연물은 세라믹을 소재로한 porcelain이었지만 최근 신소재기술의 발달로 내열성, 내후성, 내트래킹성 등이 우수한 고분자 재료들이 개발됨에 따라 구미 선진국을 중심으로 이들의 전기절연물분야 적용이 크게 증가하고 있다. 인발(pultrusion)공법으로 glass fiber와 수지를 결합시켜 고강도 무결점의 FRP절연봉이나 tube를 만들 수가 있다. 절연물에서 요구되는 구조재로서의 기계적 특성은 FRP복합재료가 충족시킬 수 있는데 이러한 봉을 core재로 하여 절연물의 표면전기특성을 만족하도록 고무로 된 shed를 씌우고 양쪽 끝에 금구류를 부착하여 composite insulator를 만들 수가 있다. composite insulator는 여러개의 shed를 한번에 진공사출하거나 shed를 금형에서 찍어 조립하여 제작할 수가 있는데 지금까지 검토되어 온 어떤 고분자 절연물보다 특성이 우수하고 장점이 많기 때문에 상업적 가치를 인정받고 있다. 본 고에서는 옥외용 절연물의 절연성능과 섬락사고기구를 요약하고 고분자신소재 절연물인 composite insulator의 장점, 국내외 개발현황, 평가방법등을 정리하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.69-71
• /
• 2001

FRP has been used very much as high strength core materials for insulators because of its high strength and good insulation properties. In this study cantilever, tension and torsion stress were simulation along to the unidirection glass fiber. In addition, FRP was made by pultrusion method. This paper proposed the procedure of the finite element model updating and pretest using the commerical finite element code MSC.Nastran. To ehance the efficiency of experimental modal analysis. we proposed the process which is the selection of the locations and the number of measurement points for pre-test.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.2
• /
• pp.58-67
• /
• 2003

Over the last decade fiber-reinforced polymer (FRP) reinforcement consisting of glass, carbon, or aramid fibers embedded in a resin such as vinyl ester, epoxy, or polyester has emerged as one of the most promising and affordable solutions to the corrosion problems of steel reinforcement in structural concrete. But reinforcing rebar for concrete made of FRP rebar has linear elastic behavior up to tensile failure. For safety a certain plastic strain and an elongation greater than 3% at maximum load is usually required for steel reinforcement in concrete structures. The same should be required for FRP rebar. Thus, the main object of this study was to develop new type of hybrid FRP rebar Also, this study was evaluated to the mechanical properties of Hybrid FRP rebar. The Manufacture of the hybrid FRP rebar was achieved by pultrusion, and braiding and filament winding techniques. Tensile and interlaminar shear test results of Hybrid FRP rebar can provide its excellent tensile strength-strain behavior and interlaminar stress-strain behavior.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.33-38
• /
• 2007

This paper reports an attempt to develop 7-wire steel tendon which is instrumented with optical FBG sensors. The tendon is devised to replace the king cable, which is located in the center of the tendon, by a steel tube in which the FBG sensor are attached along the hole using a high-mobility polyester resin. The circular steel tube has typical of 5 mm outer diameter and 1 mm inner diameter, and can easily be manufactured by means of an pultrusion process. Using the tube, in this study, three different types of one meter-long smart tendons are fabricated depending on mixture ratio of polyester resin and initiator. The performance of the FBG sensors as well as mechanical characteristics of the prototype are tested through the tensile test. Test results shows that the proposed smart tendon is in principle very effective for measuring the working strain of the tendon.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.57-62
• /
• 2006

Composite thin-walled members for civil engineering application are mainly produced by pultrusion technique, and they are generally made of a polymeric resin system reinforced by E-glass fibers due to economical reason. This material combination results in low elastic moduli of the composite materials and makes the design of composite members to be governed by stability limit state. Therefore the buckling behavior of composite thin-walled members was experimentally investigated in the present study. Axial compression was applied on each specimens by a hydraulic ram and knife edge fixtures were placed at both ends to simulate simple boundary condition. Axial compression, lateral displacements and twisting at the mid-height of each specimen were measured by a set of transducers during buckling test. The experimental buckling loads were compared with analytical results obtained through isotropic formulas. In the calculation of analytical results, elastic properties such as Young's modulus(E) and shear modulus(G) were replaced with EL and GLT obtained from coupon tests, respectively.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1530-1532
• /
• 2000

The properties of FRP usually depends on the fabricating method. The fiber orientation of FRP is also depends on the fabricating method. The fiber orientation in FRP has a great effect on the strength of FRP because the strength of FRP mainly depends on the strength of fiber. In this study. compressive and bending strength of FRP rods were investigated. Inner part of FRP was made unidirectionally by pultrusion method and outer part of FRP was made by wrapping method. The size effect was also investigated with pultruded FRP rods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.67-74
• /
• 2000

Recently western countries are now beginning to use ACM (Advanced Composite Material) in the construction industry. Compared with conventional construction materials, ACM possesses many advantages such as light-weight, high-strength, corrosion resistant properties, etc. Among other fabrication process of ACM, pultrusion is one of the promising one for civil infrastructure application. In this paper, the structural characteristics of pultruded glass fiber reinforced composite structural member of angle and tube type were studied. Experiments for compression were performed for those members along with finite element buckling analysis with ABAQUS. The experimental and analytic results were compared each other and they were also compared with predicted values using coded formulae.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.199-202
• /
• 2000

Compared with existing construction materials, ACM(Advanced Composites Material) possesses many advantage such as light-weight, high-strength, corrosion resistant properties, etc. In this study, utilizing those advantages of ACM, composite skin and comer plate for protection of concrete port structure are developed. Detailed procedure fur analysis, design and fabrication along with site installation for demonstration project are described. It is also demonstrated that pultrusion process for comer plate and VARTM process for composite skin are promising fabrication methods fer future civil infrastructure application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.85-88
• /
• 2000

FRP has been used very much as high strength core materials for insulators because of its high strength and good insulation properties. In this study cantilever, tension and torsion stress were simulation along to the unidirection glass fiber. In addition, FRP was made by pultrusion method. This paper proposed the procedure of the finite element model updating and pretest using the commercial finite element code MSC. Nastran. To enhance the efficiency of experimental modal analysis, we proposed the process which is the selection of the locations and the number of measurement points for pre-test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.402-404
• /
• 2000

The FRP pole had great advantages over other material poles. Light weight, easy installing and transporting were good characteristics. The material's superior properties represented the good durability for sea weather and air pollution, good insulation for electric, and changeable colors. In those properties, usages were like a area affected by sea, downtown, the area among the mountains and a special area for the outstanding views. It was studied that pole manufacturing method, structure analysis of pole by FEM in this study. Filament winding method was selected for a new pole manufacturing method. It produced the tapered poles and mechanically strong properties.