• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.95-98
• /
• 1999

This paper describes preliminary discussions on spatial distribution of NO density, which is mostly contained in simulated NOX exhaust, between a wire-cylinder geometry discharge gaps by using Laser Induced Fluorescence(LIF) Spectroscopy. Spatial distribution of NO density will be measured with varying NO concentrations from 166 to 644[ppm] and diameters of central electrode from 6 to 10mm. Pulsed Nd:YAG laser, Optical Parametric Oscillator(OPO), and Frequency Doubler are used to excite NO molecules to their excited state.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.263-268
• /
• 2004

The characteristics of Diesel spray droplets, such as the velocity and the diameter were simultaneously measured by using an improved Interferometric Laser Imaging for Droplet Sizing method. The experiments were carried out using an accumulator-type unit injector system and a constant-volume vessel. Two dimensional cross-section photographs of sprays were also taken using a double-pulsed Nd- YAG laser sheet and a linear array CCD camera. As a result, interesting relations between the droplets diameter and the velocity were found.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.422-424
• /
• 2000

ZnO thin films for light emission device have been deposited on sapphire and silicon substrates by pulsed laser deposition technique(PLD). A Nd:YAG laser was used with the wavelength of 355 nm. In order to investigate the emission properties of ZnO thin films, PL measurements with an Ar ion laser as a light source using an excitation wavelength of 351 nm and a power of 100 mW are used. All spectra were taken at room temperature by using a grating spectrometer and a photomultiplier detector. ZnO exhibited PL bands centered around 390, 510 and 640 nm, labeled near ultra-violet (UV), green and orange bands. Structural properties of ZnO thin films are analized with X-ray diffraction (XRD).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2256-2258
• /
• 1999

This paper describes preliminary discussions on spatial distribution of NO density, which is mostly contained in simulated NOx exhaust, between a wire-cylinder geometry discharge gaps by using Laser Induced Fluorescence(LIF) Spectroscopy, Spatial distribution of NO density will be measured with varying NO concentrations from 166 to 644 [ppm] and diameters of central electrode from 6 to 10mm. Pulsed Nd:YAG laser. Optical Parametric Oscillator(OPO), and Frequency Doubler are used to excite NO molecules to their excited state.

• Corrosion Science and Technology
• /
• 제10권4호
• /
• pp.151-155
• /
• 2011

The iron oxide particles could be resulted from the corrosion of the circulating water system of a power plant. Because it may be one of the trouble materials which affect the power generation efficiency due to the deposition on steam generator tube and turbine blade, the continuous observation of its concentration is very important. The laser induced break-down detection (LIBD) technology was applied to monitor continuously the concentration of corrosion products with the detection limit of ppb level. The measurement system consists of a Nd:YAG pulsed laser, a polarizing beam splitter, a flow-type sample cell, an acoustic emission sensor, a high speed data acquisition board, a personal computer, etc.. The performance test results confirmed that this technology can be effective to monitor the corrosion product concentration of the circulating water system of a power plant.

• 한국세라믹학회지
• /
• 제28권12호
• /
• pp.1005-1011
• /
• 1991

Y-Ba-Cu-O thin films were in-situ fabricated on LaAlO3(100) substrates using the second harmonics of a pulsed Nd:YAG laser. Thin films were deposited under 200 (mtorr) of oxygen atmosphere, when the substrate temperature was changed between 67$0^{\circ}C$ and 82$0^{\circ}C$. After deposition, the films were in-situ annealed at 50$0^{\circ}C$ under 2/3 bar of oxygen pressure. We showed that the deposition temperature affects the formation of superconducting phase, the resistance, and the surface morphology. The Y-Ba-Cu-O thin films deposited at 76$0^{\circ}C$ show the zero resistance critical temperature of 85 K.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.41-42
• /
• 2005

The characteristics of ZnO films are reported depending on different deposition conditions for film bulk acoustic resonators (FBARs). The ZnO films have been deposited on Al films evaporated on p-type (100) silicon substrate by pulsed laser deposition (PLD) technique using a Nd:YAG laser. These films exhibit an electrical resistivity higher than $10^7$ $\Omega$m. X-ray diffraction measurements have shown that ZnO films are highly c-axis oriented with full width at half maximum (FWHM) below $0.5^{\circ}$. These results show the possibility of FBAR devices using by PLD.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.88-89
• /
• 2007

ZnO thin films were deposited on $Al_2O_3$ (alumina) substrates by pulsed laser deposition (PLD) using Nd:YAG laser with a wavelength of 355nm, at room temperature and oxygen partial pressure of 1, 10, 30, 50, 100, and 200m Torr. Furthermore, deposited ZnO thin films were post-annealed at 400, 550, $600^{\circ}C$. The effects of oxygen partial pressure and post-annealing temperature on structural properties of the deposited films have been investigated by means of X-ray diffraction (XRD), and atomic force microscope (AFM), respectively. It has been found that ZnO thin films exhibit c-axis orientation, exhibiting an increased foil width at half maximum (FWHM) value of (002) diffraction peak at 30m Torr oxygen partial pressure and higher post-annealing temperature ($700^{\circ}C$).

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권4호
• /
• pp.15-18
• /
• 2006

REBCO coated conductors (RE: rare earth elements) have recently drawn great attention since they are known to possess stronger flux pinning centers in high magnetic fields compared with YBCO coated conductors. In this study, $GdBa_2Cu_3O_{7-d}(GdBCO)$ was selected to investigate the influence of the distance between target and substrate and substrate temperature on the superconducting properties of GdBCO films on the $SrTiO_3(100)$ substrate. Samples were fabricated by pulsed laser deposition (PLD) with a Nd:YAG laser (355nm). Under a given oxygen pressure of 800mTorr, we changed the distance between target and substrate from 5.5cm to 7.0cm and the substrate temperature from $750^{\circ}C\;to\;850^{\circ}C$. The crystallinity and texture of GdBCO films were analyzed by X-ray diffraction (XRD), and the surface morphology was observed by the scanning electron microscopy (SEM). Tc and Jc values were measured by the four point probe method. High quality GdBCO films with Tc of 89.7K and Jc over $1MA/cm^2$ at 77 K in self field were successfully fabricated by optimizing processing parameters. The detailed processing conditions, microstructure and superconducting properties will be presented for a discussion.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.170-173
• /
• 2001

Thin films of phase-pure perovskite (P $b_{0.72}$L $a_{0.28}$) $Ti_{0.93}$ $O_3$(PLT) were deposited in-situ onto Pt/Ti/ $SiO_2$/Si substrates by pulsed laser deposition. We have systematically investigated the variation of grain sizes depending on the process condition. Both in-situ annealing and ex-situ annealing treatments have been compared depending on the annealing time. Two-step process to grow (P $b_{0.72}$L $a_{0.28}$) $Ti_{0.93}$ $O_3$(PLT) films was adopted and verified to be useful to enlarge the grain size of the film and to enhance the leakage current characteristics. The grain sizes of PLT thin films were successfully controlled 260 to 350 nm by changing process parameters. Electrical properties including dielectric constant, ferroelectric characteristics, crystallization and leakage current of PLT thin films were shown to be strongly inf1uenced by grain size. Also PLT thin films on p-type(100) Si substrate will be fabricated by pulsed laser deposition technique using a Nd:YAG laser with different wavelengths of 355, 532 and 1064 nm. Effect of the variation of laser wavelength on dielectric properties will be discussed. Microstructural and electrical properties of the film were investigated by C-V measurement leakage current measurement and SEM.ent and SEM.