• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.14-20
• /
• 2010

In this paper, a tightly regulated triple output asymmetrical half bridge flyback (ASHF) converter is proposed. In order to regulate all output voltages, pulse frequency modulation (PFM), pulse width modulation (PWM) and phase delay (PD) are used simultaneously. In comparison with the conventional PWM-PD method, the interactions among the control variables are minimized and the operating range is increased. By the utilization of a multi winding transformer, the auxiliary transformer and the blocking capacitor are eliminated and the size and cost of the proposed converter is reduced. The operation principle of the converter is explained and the modes of operation are investigated. Based on the results, the steady state characteristics of the converter are explored. A 24V/10A, 12V/5A, 5V/10A hardware prototype is built and tested to verify the analysis results and the voltage regulation of the triple outputs of the proposed converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.2
• /
• pp.142-149
• /
• 2012

The independently regulated dual-output LLC resonant converter using only one power stage and one control IC is proposed in this paper. The conventional dual-output LLC resonant converter requires the extra non-isolated DC/DC converter to obtain the tightly regulated slave output voltage, which results in the low power conversion efficiency and high production costs. On the other hand, since the proposed converter controls the master and slave output voltages by pulse width modulation(PWM) and pulse frequency modulation(PFM), it can achieve tightly regulated dual output voltages without the additional non-isolated DC/DC converter. Therefore, it features a high efficiency and low cost. To confirm the validity of the proposed converter, theoretical analysis and experimental results from a 40W LED driver prototype are presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.522-529
• /
• 2014

This study proposes an isolation amplifier circuit for the sensing and feedback of inverter DC-link voltage, which is inevitable for the precise control of inverter output voltage. The isolation amplifier consists of a pulse-width modulator and a pulse transformer with dual secondary windings. The accuracy of the proposed circuit depends on the precise matching of filter parameters in dual secondary circuits. The influences of parameter inaccuracy on the amplifier performances are analyzed. A modified circuit is proposed to reduce the dependency on filter parameters. The validity of the proposed method is verified through simulation and experiment.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.3
• /
• pp.254-262
• /
• 1990

In the active power filter, the PWM method for controlling the power converter plays an important role for the performance and the efficiency of the filter. In this paper, a new PWM method for the single phase current source type active power filter is presented, which is intended particularly for obtaining the maximum efficiency of the compensation. This method is basically based upon the optimized injection method, but in contrast to the existing method, this method adapts the optimized injection method by putting not only the pulse width, but also the pulse position into control variables. By doing this, when the number of pulses per one cycle is N, lower order harmonics up to the Nth order can be completely eliminated by the filter. So, this method is much more efficient than any other existing method. These characteristics are well verified by the computer simulations and the experiments.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1091-1096
• /
• 2011

The main factors of radar signals used in electronic warfare are Radio Frequency(RF), Pulse Repetition Interval(PRI), Pulse Width(PW), Scan Parameter(SP) and so on. This radar signals may have some important information for the electronic warfare. So, there is a necessity for making a threat database to decide whether the radar signal is a threat or not. When the electronic support system collects some threat radar signals, it needs the search band to control the receivers and filter banks of the system. In this paper we propose search band implementation considering the type and center frequency of the receivers of the electronic support system.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1416-1417
• /
• 2007

The high frequency pulsed power system is widely available for use in high frequency generator applications. We designed and fabricated our own high frequency pulsed power system to obtain very sort pulse width and high peak value and investigated microbe removal characteristics using it. This paper introduces a simple high voltage high frequency pulsed power system for removing various bacteria caused by dirty water. This system include power supply circuit, switching MOSFET, and flyback converter. We can also control the switching using a PIC one chip microprocessor. As a result, we can obtain good removing characteristics of various bacteria by adjusting the charging voltage, the pulse repetition rate and the electrical field inducing time.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.362-368
• /
• 2023

In this paper, we presented the characteristics of the impulse signal which is applicable to the ultra-wideband antennas. In general, the width of the impulse has around sub nano or pico seconds in the time domain, where it corresponds to the wideband in the frequency domain. We confirmed by experiment that the impulse has around 130ps of the pulse width and bandwidth of 4GHz when 10MHz of sine wave excited as an input pulse. The fidelity factor was calculated in the time domain and -10dB bandwidth in the frequency domain was investigated for resistively loaded dipole antennas with different resistance per unit length. The received impulse signal through the wideband antennas is confirmed in the time and frequency domains that received pulse is to be similar to the generated impulse. The fidelity and bandwidth of the quantity value are 0.98 and 3.4GHz, respectively.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.2
• /
• pp.93-98
• /
• 2024

This paper presents the method to extract the ultrawide-band (UWB) signal and proposes the simple impulse radar system for sensing real-based target within close-range area. The proposed impulse radar system consists of impulse generator, ultrawide-band antennas, function generator, and digital oscilloscope. It is verified by experiment that a differentiated Gaussian pulse is generated with 200ps of pulse width and corresponding spectrum from 0.3 to 4.7 GHz once a sinusoidal wave with 10MHz is excited. The Gaussian doublet is received by identical antennas and it is shown that the UWB pule width of 328ps and its spectrum is from 0.9 to 4.4 GHz. It is confirmed that the UWB pulse is extracted when the real-based targets such as circular target with 4cm radius and corner reflector are placed at the close-range area.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1339-1345
• /
• 2006

The development of an accurate and energy saving electro-pneumatic regulator that may be applied to a variety of practical pressure control applications is described in this paper. A novel modified pulse width modulation (MPWM) valve pulsing algorithm allows the electro-pneumatic regulator to become energy saving system. A comparison between the system response of conventional PWM algorithm and that of the modified PWM (MPWM) algorithm shows that the control performance is almost the same, but energy saving is greatly improved by adopting this new MPWM algorithm. The effectiveness of the proposed control algorithm is demonstrated through experiments with various reference trajectories.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.781-787
• /
• 2009

This research is concerned with the application of the active linear actuator to the active vibration control of structure. The active linear actuator will be mounted on the sub-frame so that it can cancel the excitation transferred from the engine. Accelerometer mounted on the sub-frame detects the vibration and its signal is fed into the DSP controller where the control algorithm is installed. The output of the DSP controller is connected to the driver which amplifies the DSP output. In general, the pulse width modulation power amplifier is used to drive the voice-coil type actuator. This study shows the dynamic characteristics of the active linear actuator and active vibration control experimental results.