• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.13 no.2
• /
• pp.14-23
• /
• 2009

In the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse are the arterial pulsation position of the Lung Channel of Hand-Taeuem(手太陰) and the Stomach Channel of Foot-Yangmyeong(足陽明). At the pulses we can examine the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽), the deficiency and excess of the diseases, whether the disease is in Uem-Channel(陰經) or Yang-Channel (陽經), whether the disease is internel injury or externel injury. In the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse are in front of the Right-Kwan(右關) and the Left-Kwan(左關) the distance of 1 Pun(分) because of completion of the Chon-Ku-Pulse-Taking(寸口脈診). The purpose of examnation is same to . In the Kwan-Pulse(關脈) doesn't have the position. It has only the role of a gateway of the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽). And it is same to role of the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse in . So we can think that the Kwan-Pulse(關脈) in and the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse in are the same thing. And we must have the different standard when examine the condition of Sam-Cho(三焦) and the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽) because the position of the Kwan-Pulse(關脈) came out after the time of .

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.18 no.2
• /
• pp.149-160
• /
• 2008

Bag-filter system has been widely used in industrial field to remove the particulate matters from the exhaust gas. The cylindrical type of bag-filter has been generally used. But it has many shortcomings. The reattachment of separated particles on the surface of bags could result in high pressure drop of bag-filter system and subsequent decrease of air flow rate since the cylindrical type bag-filter system should have the upward flow pattern. In addition, the supply of very high pressure pulse air jet to remove particulate matters on the surface of filter could result in a frequent rupture of bags. To overcome these shortcomings of the cylindrical type, the rectangular type was developed in the developed countries and imported to Korea. But, there was not many design data available to understand the mechanisms. Thus, the fundamental experiments were conducted in this study to get some ideas about the pulse jet cleaning of rectangular type bag filter system. The experimental factors are as follows; pulse distance, pulse duration, pulse interval, pulse pressure and pulse nozzle type. Experiments followed the factorial design method. With the shorter pulse distance, the distribution of pressure drops was relatively not uniform while the particulate removal efficiency was higher. With the longer duration of pulsing and the more number of pulse nozzle, the removal efficiency was higher and the pressure drop distribution was more uniform.

• Journal of Welding and Joining
• /
• v.22 no.1
• /
• pp.58-64
• /
• 2004

The control of the weld bead shape is important in laser welding of the small parts. The effects of laser welding parameters on the weld bead shape in the pulsed Nd:YAG laser welding of STS 304L material were investigated. Shielding gas type, flow rate, pumping voltage, pulse frequency, pulse width, focal position and overlap distance were selected as laser welding parameters. Experiments were designed and conducted using the Taguchi method which was a statistical experimental method. The weld bead width, penetration, area and aspect ratio were measured and analysed as the weld bead shape properties and the welding parameters were optimized to maximize the weld aspect ratio. Weld aspect ratio were greatly affected by the pulse width, pumping voltage and pulse frequency, and somewhat by the overlap distance, and little by the shielding gas type, flow rate and focal position. A confirmation experiment were conducted using the optimized welding parameters.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.18 no.3
• /
• pp.189-203
• /
• 2008

Cylindrical bag filter system with pulse jet cleaning has been the most common device to control particle laden exhaust gas from the various industrial processes. But, it has many shortcomings due to particle reattachment and frequent bag rupture. In recent years, rectangular type bag filter system has been developed to overcome the problems associated with the cylindrical system. However, not many studies about the rectangular system were not done, compared to the cylindrical system. In this study, the optimum pulse jet cleaning conditions were thus tested by the series of experiments. The factors tested in this study are pulse distance, pulse pressure, pulse duration, the number of holes for pulsing and bag materials. A single bag ($1,500mmL{\times}50mmW{\times}300mmH$) system and a multi-bags (3 bags in a row) were tested separately. The highest removal efficiency with a single bag system was found at the conditions with pulse distance of 10cm, pulse pressure of $3kg/cm^2$, pulse duration of 0.3s, pulse jet number of 6 and Polyester bag. With the multi-bags system, the best cleaning conditions were found at the bag interval of 20cm with the simultaneous pulsing and the bag interval of 15cm with the serial pulsing.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.3 s.309
• /
• pp.41-50
• /
• 2006

This paper presents a novel ultrasonic sensor system to overcome limited distance detection range that can be measured only more than 30cm by single ultrasonic transducer. This is accomplished by separation of receiving capacitive ultrasonic transducer from transmitting capacitive ultrasonic transducer. And hardwares and software of the system are described in detail. The system makes very close range as well as long range detect by wireless precisely. Frequency of trigger pulse is 10Hz, but it is very low frequency for transmitting data in wireless module. Therefore, for triggering between receiver and transmitter, an algorithm for mixing and distinguishing trigger pulse from carrier pulse by software is proposed. The system is designed by common microprocessor 8051. The performance of the proposed method has been assessed through two types. The first, transmitting and receiving transducer are put on both sides. And then, distance of two point is measured as far as 0mm. Secondly, transmitting transducer send out ultrasonic pulse and measure the time of flight(TOF) until a first echo from an object detected by the detached receiving transducer. The distance between the detached transducers and a reflecting object is measured as far as 7cm. Images of measured ultrasonic waves and TOF for two methods presented to prove effectiveness of results.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.49-51
• /
• 2007

It is as result that study to apply mini magnet nerve curer in peripheral nervous system disease treatment. Design and embodied action power and Control Unit in cylinder form of magnet roof object firstly. Yielded service area about special quality of probe of roof object cylinder style and treatment area dimension and distance of treatment pulse secondly. Embody pulse forming course energy value by Probe's form by third, could embody treatment pulse by disease. Specially, through a special quality experiment, saved Damping pulse torn and treatment pulse form etc. variously. Lately, embodied this to aid a little in disease treatment that follow that there is no invasion that there is no stimulation by medicine development. Go amplitude treatment pulse (traditional magneto-therapy of greatly great that strong) does curative effect greatest at short time and becomes thought that demand is magnified greatly at the future in this research.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.4
• /
• pp.307-311
• /
• 2017

Ultra short pulse laser processing with the PI (polyimide) substrate is conducted to increase flexibility and radius of curvatures. A femtosecond laser is used to perform micro machining by minimizing the heat effect in PI substrate. The laser processing according to the parameters, such as fabricated line width, depth, laser power, distance between lines, is carried out to understand the characteristics of fabricated lines. A bending test is carried out to evaluate bending shapes and the radius of curvature after bending and spreading it 1000 times. The results demonstrates that the radius of curvature decreases in deepen lines and increases with the augment of the number of the fabricated lines, and distance between lines.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.205-208
• /
• 1995

PZT powders were prepared by the molten salt synthesis method. The porous PZT specimens were prepared from a mixture of PZT and Polyvinylalcohol(PVA) powders by BURPS(Burnout Plastic Sphere) technique. The pulse-echo response of PZT-polymer 3-3 type composite transducer with various PVA wt.% were studied, The fall time of pulse-echo response of PZT-polymer 3-3 type composite transducer was shorten to that of solid PZT-maded transducer. Therefore, a good transmitting and receiving properties could be obtained. The distance between transducer and reflector was in good agreement both solid PZT and PZT-polymer 3-3 type composite fabricated transducer.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.2
• /
• pp.252-257
• /
• 2010

SAR has pulse compression gain through the process including range and azimuth. Efficient jammers against the SAR with simulated elements are evaluated in the view of power and SAR image. In this paper, J/S is analysed for SAR with RF propagation equation firstly. Several jamming signals on SAR signal are made into SAR image through pulse compression process. Objective jamming performance is evaluated using euclidean distance.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1052-1058
• /
• 2003

The possibility of micro/nano machining through electro-chemical process is discussed in this research. Electro-chemical dissolution region is localized within 1 ${\mu}m$ by applying ultra short pulses with tens of nanosecond duration. The effects of voltage, pulse duration, and pulse frequency on the localization distance are investigated. Localization distance can be manipulated by controlling the voltage and pulse duration, and various hole shapes are produced including stepped holes and taper free hole. High quality micro-hole with 8 ${\mu}m$ diameter with 20 ${\mu}m$ depth and micro-groove with 9 ${\mu}m$ width with 10 ${\mu}m$ depth are machined on 304 stainless steel.