• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.123-128
• /
• 2006

Enzymatic deinking method can avoids the alkaline environment as usual required in chemical deinking, which consequently cuts chemical costs and reduced the white water pollution. The electrostatic wastepaper was dinked with commercial cellulolytic enzymes and surfactant in neutral pH and the effectiveness of deinking and the physical properties of deinked pulp were evaluated. The disintegrating efficiency of the electrostatic wastepaper in neutral pH was enhanced with enzyme treatments. Although the freeness of deinked pulp with enzymes was higher than that of deinked pulp with chemical deinking agents, the brightness of the enzymatic deinked pulp was slightly lower than that of the chemical deinked pulp. But, by additions of nonionic surfactants, the brightness of deinked pulp was increased with less residual ink particles and mechanical properties of enzymatic deinked pulp was improved compared to the deinked pulp of conventional alkaline method.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.5
• /
• pp.12-19
• /
• 2007

Enzymatic deinking method can avoids the alkaline environment as usual required in chemical deinking, which consequently cuts chemical costs and reduced the white water pollution. The electrostatic wastepaper was dinked with commercial cellulolytic enzymes and surfactant in neutral pH and the effectiveness of deinking and the physical properties of deinked pulp were evaluated. The disintegrating efficiency of the electrostatic wastepaper in neutral pH was enhanced with enzyme treatments. Although the freeness of deinked pulp with enzymes was higher than that of deinked pulp with chemical de inking agents, the brightness of the enzymatic deinked pulp was slightly lower than that of the chemical deinked pulp. But, by additions of nonionic surfactants, the brightness of deinked pulp was increased with less residual ink particles and mechanical properties of enzymatic deinked pulp was improved compared to the deinked pulp of conventional alkaline method.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.73-80
• /
• 2015

Corn stalk is the lignocellulosic biomass, which remain as leftover after harvesting. To use the corn stalk as raw material for paper industry, soda pulping was applied. In chemical compositional analysis, extractive contents of corn stalk (45.1%) was higher than hardwood. With corn stalk pith, soda pulp yield was 25.3% at 10.6 Kappa number, but 39.5% yield with 14.8 Kappa number for corn stalk rind. Higher extractives content in pith is one of the reason for lower pulp yield than rind. Pith pulp fibers had higher fines content than rind pulp. Pith parenchyma cell was removed as fines during pulping or washing process, which caused the lower yield. To use the corn stalks as a raw material for paper making, de-pith process is essential for higher pulp yield and longer pulp length.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.375-380
• /
• 1999

In order to improve the optical properties of high yield pulp, bleached chemi-thermo-mechanical pulp (BCTMP) was produced from CTMP of Betula maximowicziana Regel by two staged ozone-hydrogen peroxide bleaching. This pulp was used for the evaluation of the improvement of optical properties, chemical characteristics of lignin in fiber, and the relationship between lignin and optical properties in fiber cell wall. By hydrogen peroxide treatment, the brightness was improved, but the post color number (PC No.) was not. There was little improvement on optical properties by ozone treatment, but his could be solved by using two staged ozone-hydrogen peroxide bleaching. The hydrogen peroxide treatment did not make nay change on chemical characteristics of lignin in cell wall, but by ozone treatment, it was found that the non-aromatic conjugated structure was existed in the surface of cell wall, but this could be removed by hydrogen peroxide treatment in two staged ozone-hydrogen peroxide treatment. Therefore, the optical properties was significantly improved due to the removal of non-aromatic conjugated structure.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.2
• /
• pp.57-64
• /
• 2008

In general, the entire of paper mulberry bark, which is not cut into pieces with an appropriate length, have been used in the pulping. This kind of pulping method couldn't accomplish the improvement of beating and sheet forming efficiency. For this reason, we investigated the effects of the cutting length of paper mulberry bast fiber on pulping and Hanji (Korean traditional paper) properties, in order to develop high quality Hanji manufacturing process. The cutting length variation of paper mulberry white bast did not great effects on pulp yields. The pulp yields based on pulping methods were sulfomethylated pulping av. 57.4%, alkali-hydrogen peroxide pulping av. 55.4%, and alkaline pulping av. 53.5% respectively. The optical properties such as brightness, opacity, scattering coefficient, and absorption coefficient were slightly improved by the increase of paper mulberry white bast cutting length. The increase of paper mulberry white bast cutting length resulted in poor sheet formation. Physical properties such as breaking length, TEA, tear index, burst index, and folding endurance were slightly improved by the increase of cutting length. The modified pulping processes, which used sulfomethylated method and alkali-hydrogen peroxide method, showed better pulp and sheet properties than conventional alkaline pulping.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.04b
• /
• pp.239-244
• /
• 1999

aluminum sulfate (alum) as a representative retention aid in papermaking processes was added to pulp suspensions, and the aluminum components adsorbed on the pulp were investigated quantitatively by two types of X-ray elementary analyses with regard to simultaneous changes of their surface charges. X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence analysis (XFA) were applied to determine the aluminum components retained in pulp pads up to ca. 10 nm and 100${\mu}$m depth, respectively. In other words, XPS was utilized to analyze the outermost surface layers of the samples, and XFA was available for measurement of their extensive regions. A particle charge detector (PCD) was used to monitor streaming potentials at various pHs of the pulp mixtures under moderate sharing conditions. At pH 4.5 of pulp suspensions containing alum, surface charges of pulp fibers varied from negative to slight negative (approximately neutral) according to adsorption of aluminum components onto the pulp fibers. Subsequently, when a dilute NaOH solution in limited amounts was added to pulp mixtures, both streaming potentials and surface aluminum content of the pulp fibers increased distinctly although little total aluminum retention increased. Further addition of alkali solutions brought drastic decreases of the surface charges and surface aluminum content, while total aluminum content, on the contrary, increased gradually under neutral conditions. These results indicate that residual aluminum ions remained in pulp suspensions are predominantly adsorbed on surfaces of pulp fibers by adequate alkali additions and they must sufficiently cationize the fiber surfaces with increases of somewhat cationic aluminum complexes formed on the surfaces. On the other hand, aluminum components formed in higher pH ranges have nearly no contribution to improvement of charge properties of the pulp fiber surfaces, even though aluminum retention in pulp pads increases. XPS and XFA analyses combined with streaming potential measurement using a PCD suggest close relationships between aluminum content on the pulp fiber surfaces and their charge properties.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.1
• /
• pp.95-102
• /
• 2000

This paper presents the second part of a study of deinking using wort. Physical properties of deinked pulps such as tensile strength, bursting strength and tearing resistance were investigated. In order to analyze the properties, the fiber length and coarseness of deinked pulp was also measured. Results of deinking experiments showed that the deinking efficiency of enzyme treatments was higher than that of chemical treatments in strength properties such as tensile strength, bursting strength and tearing resistance on the the whole. we think that the reason why is that the fiber length and coarseness of deinked pulp with wort are more increased and decreased than those of deinked pulp with chemicals individually.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.83-90
• /
• 2016

Increasing the amount of filler in paper is of high interest for paper industry while maintaining its key sheet quality properties. In this study, a MFC-GCC composite, made through a co-grinding NBSK (Northern bleached softwood kraft) pulp with a ground calcium carbonate (Intracarb 60), was used as a strength aid in paper in order to evaluate a potential cost reduction through filler increase without sacrificing paper quality. Hand-sheets were made of NBSK and/or eucalyptus pulp by using white water recirculation in a Tappi sheet former and was compared its properties without or with MFC additions at different filler levels. It was found that the MFC-GCC composite has a large surface area compared to the fiber, allowing the formation of more hydrogen bonds in the web, thus giving natural strength to the paper. Overall results are encouraging that the MFC-GCC composite allows papermaker to reduce basis weight and maintain critical sheet properties.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.2
• /
• pp.12-17
• /
• 2003

The effects of wet pressing and drying conditions on the disintegration and physical properties of paper were investigated in order to get the basic information on the resistance of paper for aqueous solution during converting processes. Wet pressing of unbeaten bleached softwood kraft pulp increased WRV at the range of grammage investigated. The increase of WRV with grammage at low wet pressing pressure(50 psi) was obvious, while it was not significant at higher wet pressing pressure(110 psi). The changes of WRV by drying were affected by the grammage and wet pressing pressure. The poorer disintegration of sheet, the higher wet pressing pressure and drying temperature. Although the strength properties were increased with the grammage, wet pressing pressure and drying temperature, results showed different trend from those of beaten pulp.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.1
• /
• pp.39-45
• /
• 2014

Various approaches have been tried to reduce the emission of carbon dioxide in paper industry. One of important approaches is to use PCC manufactured from emission gas as a filler. However, it was recognized that PCC is inferior to other fillers in the paper strength properties of view. Therefore, pretreatment of PCC with pulp powder was tried to mitigate the strength reduction of paper. Pretreatment of PCC with pulp powder improved the bulk(7.4~12.9%) and air permeability(24.8~42.98%), but there is no significant change in opacity. Tensile index, burst index and stiffness were decreased by the use of pretreated PCC with pulp powder. Anionic and cationic PAM were used as a additive for PCC pretreatment in order to improve strength properties. There was no significant change in bulk in all kinds of PAM used in this study. Most strength properties were improved by the pretreatment of PCC with the anionic and cationic PAM and pulp powder, although the opacity and stiffness were more or less decreased.