• Structural Engineering and Mechanics
• /
• v.12 no.6
• /
• pp.657-668
• /
• 2001

Fiber reinforced cementitious composites are nowadays widely applied in civil engineering. The postcracking performance of this material depends on the interaction between a steel fiber, which is obliquely across a crack, and its surrounding matrix. While the partly debonded steel fiber is subjected to pulling out from the matrix and simultaneously subjected to transverse force, it may be modelled as a Bernoulli-Euler beam partly supported on an elastic foundation with non-linearly varying modulus. The fiber bridging the crack may be cut into two parts to simplify the problem (Leung and Li 1992). To obtain the transverse displacement at the cut end of the fiber (Fig. 1), it is convenient to directly solve the corresponding differential equation. At the first glance, it is a classical beam on foundation problem. However, the differential equation is not analytically solvable due to the non-linear distribution of the foundation stiffness. Moreover, since the second order deformation effect is included, the boundary conditions become complex and hence conventional numerical tools such as the spline or difference methods may not be sufficient. In this study, moment equilibrium is the basis for formulation of the fundamental differential equation for the beam (Timoshenko 1956). For the cantilever part of the beam, direct integration is performed. For the non-linearly supported part, a transformation is carried out to reduce the higher order differential equation into one order simultaneous equations. The Runge-Kutta technique is employed for the solution within the boundary domain. Finally, multi-dimensional optimization approaches are carefully tested and applied to find the boundary values that are of interest. The numerical solution procedure is demonstrated to be stable and convergent.

• Safety and Health at Work
• /
• v.1 no.2
• /
• pp.149-157
• /
• 2010

Objectives: To quantify disability level in salespeople with concurrent low back pain (LBP) and to determine the relative associations between demographic, occupational, psychosocial and clinical factors and back disability. LBP is the most common cause of work-related disability in people under 45 years of age and the most expensive cause of work-related disability, in terms of workers' compensation and medical expenses. Evidence suggests high prevalence of LBP in salespeople. Methods: A cross-sectional survey was conducted in which 184 saleswomen with a current episode of self-reported LBP working in a large up-scale department store filled out a battery of 6 self-administered questionnaires and received a standardised physical examination. Results: Saleswomen with concurrent LBP had low disability levels. Factors significantly associated with disability were pain intensity, measured by a visual analogue scale, in the past week (p < 0.001), physical and mental health status (p < 0.001, p = 0.003, respectively), fear avoidance scores for both work and physical activities (p = 0.031, p = 0.014, respectively), past history of LBP (p = 0.019), and self-reported frequency of pushing or pulling objects placed in high positions during work (p = 0.047). A significant level (45%) of the variance in disability status was explained by these variables. Conclusion: In clinical management of LBP workers who required prolonged standing, such as salespeople, clinicians should look for modifiable risk factors associated with disability. Specific measures need to be taken to prevent disability due to LBP among salespeople.

• Physical Therapy Rehabilitation Science
• /
• v.6 no.1
• /
• pp.33-38
• /
• 2017

Objective: This study tried to examine the muscle activity of the neck and trunk according to head posture changes during use of laptops. Design: Cross-sectional study. Methods: This study included nineteen young men and women. All subjects maintained each posture while practice typing on laptops for ten minutes with a 5-minute break between each posture. For the neutral head posture, the subjects practiced typing while pulling their chins down towards the Adam's apple and were able to look at their knees while having their external auditory meatus, acromion, and greater trochanter vertical to the ground. For the natural head posture, they practiced typing while balancing their posture between extension and flexion of the cervical vertebrae by themselves without any guidelines. While a forward head posture was created by having their heads face the front horizontal to the rope hanging from the ceiling, they practiced typing with their external auditory meatus located in the place which was 5 cm in front of the vertical plane. The subjects used general word process but practiced typing with accuracy and high speed. Muscle activities were randomly measured using surface electromyography according to each postures. Results: The research result had found that muscle activity with the natural head posture was more significantly reduced than that of the forward head posture in the sternocleidomastoid muscle, upper trapezius, cervical vertebral spinae, and thoracic vertebrae spinae muscles (p<0.05) and that the neutral head posture was more significantly reduced than that of forward head posture in the upper trapezius, cervical vertebral spinae, and thoracic vertebrae spinae muscle activity (p<0.05) with significant increases in lumbar spinae muscle activity (p<0.05). Also, muscle activity with the neutral head posture significantly increased more in the sternocleidomastoid muscle and lumbar spinae than that of the natural posture (p<0.05). Conclusions: Our study results suggest that in order to prevent musculoskeletal pain, the neutral head posture with use of laptops is effective in reducing load to the shoulders and vitalizing the postural muscles.

• Fibers and Polymers
• /
• v.5 no.4
• /
• pp.253-258
• /
• 2004

Living nature of photoinduced cationic polymerization of isobutyl vinyl ether (IBVE) in the presence of various combinations of diphenyliodonium halide (DPIX), a photocationic initiator and zinc halide $(ZnX_2)$ in methylene chloride has been investigated. Attainment of $100\%$ conversion and a linear relationship between $\%$conversion and number average molar mass of the resulting polymer, strongly suggests the living nature of this system. Livingness of the polymerization system was observed irrespective to the type of halide anion of the initiator and zinc salts unless the reaction temperature is not higher than $-30^{\circ}C$. The rate of polymerization decreases in the order of iodide > bromide > chloride when halide salt of DPIX and $ZnX_2$ are used. It is postulated that the cationic initiation is started by the insertion of weakly basic monomer in to the activated C-X terminal of the monomer adduct which is a reaction product of monomer and HX, a photolytic product of DPIX, formed in situ during the photo-irradiation process. It was concluded that polymerization is initiated by the insertion of weakly basic monomer into activated C- X terminal of monomer adduct due to the pulling action of$ZnX_2$, which successively producing a new polarized C-X terminal for the propagation in cationic nature. This led us to a conclusion that the living nature of this cationic polymerization is ascribable to the polarized C-X growing terminal, which is stable enough to depress the processes of chain transfer or termination process.

• Journal of Pharmacopuncture
• /
• v.7 no.1 s.12
• /
• pp.63-69
• /
• 2004

Objective : This study was designed to find out whether NS(normal saline) is able to be constituted as an appropriate control group for CC(Cervi Cornu Parvum herbal acupuncture), CF(Carthami-Flos herbal acupuncture) and BV(bee venom herbal acupuncture). Method : NS and three herbal acupuncture were inserted into Quchi(LI 11) of the subjects. After 5 minutes the subjects completed a questionnaire rating the intensity of 21 kinds of acupuncture sensation; hurting, penetrating, sharp, aching, intense, spreading, radiating, tingling, pricking, stinging, pulling, heavy, dull, numb, electric, shocking, hot, burning, cool, pulsing, and throbbing. We compared subjective evaluations of acupuncture sensation between or among the groups. Results : As for CC half items of the acupuncture sensation were significantly different from NS. As for CF all items were not significantly different from NS. As for CC all items were significantly different from NS except one item. In general the score of CF acupuncture sensation was lower than the others and the score of BV acupuncture sensation was higher than the others from comparison of sensation among herbal acupunctures(CC, CF, BV). Conclusion : We found that NS is able to be an appropriate placebo herbal acupuncture for CF. Further study is needed for new placebo herbal acupuncture for CC and BV.

• Korean Journal of Applied Biomechanics
• /
• v.23 no.3
• /
• pp.209-218
• /
• 2013

This study was to perform the kinetic analysis of forward $1\frac{1}{2}$ somersault on the platform diving. Six men's diving players of the Korea national reserve athletes participated in this study. The variables were analyzed response time, velocity, center of mass (COM), angle, center of pressure (COP) and ground reaction force (GRF) of motion. For measure and analysis of this study, used to synchronized to 4 camcorder and 1 force plate, used to the Kwon3D XP (Ver. 4.0, Visol, Korea) and Kwon GRF (Ver. 2.0, Visol, Korea) for analyzed of variables. The results were as follows; Time factor were observed in maximum knee flexion depending on the extent of use at phase 1 of take-off to execute the somersault. This enabled the subject to secure the highest possible body position in space at the moment of jumping to execute the somersault and prepare for the entry into the water with more ease. Regarding the displacement of COM, all subjects showed rightward movement in the lateral displacement during technical execution. Changes in forward and downward movements were observed in the horizontal and vertical displacements, respectively. In terms of angular shift, the shoulder joint angle tended to decrease on average, and the elbow joints showed gradually increasing angles. This finding can be explained by the shift of the coordinate points of body segments around the rotational axis in order to execute the half-bending movement that can be implemented by pulling the lower limb segments toward the trunk using the upper limb segments. The hip joint angles gradually decreased; this accelerated the rotational movement by narrowing the distance to the trunk. Movement-specific shifts in the COP occurred in the front of and vertical directions. Regarding the changes in GRF, which is influenced by the strong compressive load exerted by the supporting feet, efficient aerial movements were executed through a vertical jump, with no energy lost to the lateral GRF.

• Korean Journal of Applied Biomechanics
• /
• v.30 no.2
• /
• pp.131-144
• /
• 2020

Objective: The purpose of this study was to examine the effect of degrees of freedom on the multi-synergies in two hierarchies of human hand system during force production and releasing tasks. Method: In this study, the constrained movements of the aiming and releasing actions using both hands and fingers during archery-like shooting were implemented as experimental tasks. The participants produced a pulling force holding the customized frame (mimicking an archery bow, with a set of force transducers) and kept it consistently for about 5 seconds, and released fingers as quickly as possible in a self-paced manner within the next 5 seconds. An analytical method based on the uncontrolled manifold hypothesis was used to quantify the stability index (synergy index) in two hierarchies including two hands (upper hierarchy) and individual fingers (lower hierarchy). Results: The results confirmed that the positive synergy pattern showed simultaneously at the upper and lower hierarchies, and the kinetic degrees of freedom were associated with the increment of hierarchical synergy indices and the performance indices. Also, the synergy indices of both hierarchies showed significant positive correlations with the performance accuracy during the task. Conclusion: The results of this study suggest that the human control system actively uses extra degrees of freedom to stabilize task performance variables. Further increasing the degree of freedom at one level of hierarchy induces positive interactions across hierarchical control levels, which in turn positively affects the accuracy and precision of task performance.

• Archives of Plastic Surgery
• /
• v.37 no.4
• /
• pp.504-508
• /
• 2010

Purpose: Traumatic telecanthus can result from nasoethmoid-orbital fractures. Repair of the medial canthal tendon (MCT) using transnasal wiring is regarded as a choice of method to treat telecanthus, however, is often complicated by incomplete anchoring and drift of canthus, extrusion of wire, in-fracture of orbital bone, and eye damage. The authors introduced oblique transnasal wiring method through the Hiraga's epicanthopalsty incision instead of well-known classical bicoronal approach. Methods: Five patients with traumatic telecanthus were treated with this method. Though the Hiraga's epicanthoplasty incision, we could approach the operative field; the medial orbital wall and detached MCT. Oblique transnasal wiring was performed as following steps. After slit skin incision on the contralateral nasal recession area, drill holes were made from this point to the superior and posterior point of lacrimal sac of deformed eye. A 2-0 wire was double-passed through the holes and MCT. Traction was applied to ensure pulling the MCT and the wires were twisted in the contralateral nose, securing the MCT in the correct position. Results: All patients except 1 person showed improvement and rapid recovery. On average each canthus was moved 5.6 mm medially. In all cases, there were no eyelashes disappear, lacrimal canaliculitis, lacrimal duct injury, or infections. Conclusion: The Hiraga's epicanthoplasty incision could give sufficient operative field to reattach the MCT in traumatic telecanthus patients. And the oblique transnasal wiring technique is effective for the Asians who have flat nose and exophthalmic eye. The authors conclude that this technique could be a simple, safe and scarless method to correct traumatic telecanthus.

• Archives of Plastic Surgery
• /
• v.37 no.4
• /
• pp.496-498
• /
• 2010

Purpose: Lacerations requiring formal wound closure compose a significant number of all childhood injuries presenting to the emergency department. The problem with conventional suture technique are that suture removal is quite cumbersome, especially in children. Unwanted soft tissue damage can result in the process of suture removal, which calls for sedation, stressful for both medical personnel and child. The purpose of this study is to introduce the convenient suture technique for pediatric facial lacerations. Methods: Children under the age of four, presenting to the emergency department with facial lacerations were enrolled in the study. From March 2008 to June 2009, 63 patients (41 males and 22 females) with an average age of 1.4 years were treated with our convenient suture technique using utilized a loop suspended above a double, flat tie. Clean, tension free wounds were treated with our technique, wounds with significant skin defect and concomitant fractures were excluded. Results: The Patients were followed-up in 1, 3 and 5 days postoperatively. On the third hospital visit, suture removal was done by simply cutting the loop suspended above the wound margin and gently pulling the thread with forceps. There were no significant differences in the rates of infection and dehiscence compared with conventional suture technique. Conclusion: The use of our technique was to be simple with similar operative time compared with conventional suture technique. Removal of suture materials were easy without unwanted injuries to the surrounding tissue which resulted in less discomfort for the patient and greater parental satisfaction, minimized the complications. It can be considered as a viable alternative in the repair of pediatric facial lacerations.

• Archives of Plastic Surgery
• /
• v.45 no.1
• /
• pp.23-28
• /
• 2018

Background Condylar process fractures account for one-third of all mandibular fractures, and the distal fragment is prone to dislocate to the medial side due to the pulling of the lateral pterygoid muscle. Retromandibular approaches are commonly used, but the intraoperative view becomes limited in medially dislocated fractures. This study summarized a series of cases of retromandibular reduction for medially dislocated condylar process fractures and described our supplementary procedure to realign the dislocated condylar process. Methods Nine patients with medially dislocated condylar process fractures underwent surgical correction from January 2012 to December 2016. In 6 of them, it was possible to realign the fractures with a conventional retromandibular approach, but for 3 cases of severe dislocation to the middle cranial fossa, a supplementary transoral procedure was carried out. The angle difference between the ramus and condyle, ramus height, and maximal mouth opening (MMO) were evaluated. Results All 9 cases were restored to the proper anatomical alignment without any major complications, and postoperative images revealed successful union. The angle difference was $8.94^{\circ}{\pm}4.11^{\circ}$ preoperatively, and $0.99{\pm}0.49^{\circ}$ at the 6-month follow-up. The pretreatment ramus height difference was $6.12{\pm}6.09mm$, and the postoperative difference was $0.18{\pm}0.10mm$. These changes after surgery were statistically significant. The MMO before surgery was $11.44{\pm}3.0mm$, and the postoperative MMO was $37.2{\pm}2.9mm$, reflecting a significant increase after reduction. Conclusions Retromandibular reduction is a useful method in medially dislocated condylar process fractures, and additional transoral assistance should be considered to realign condylar processes that severely dislocate to the middle cranial fossa.