• 한국구조물진단유지관리공학회 논문집
• /
• 제20권4호
• /
• pp.51-58
• /
• 2016

콘크리트 구조물은 내구성과 경제성이 확보된 건설재료이지만, 매립된 철근의 부식은 내구적인 문제뿐 아니라 구조물의 안전성에 큰 영향을 준다. 본 연구는 유리섬유와 강재를 에폭시로 일체화 시킨 FRP Hybrid Bar를 적용한 콘크리트에 대해 염해 침투 저항성과 부식수준에 따른 부착성능을 평가하였다. 이를 위해 일반 강재를 적용한 OPC(Ordinary Portland Cement)시편과 GGBFS를 30% 혼입한 시편에 대하여 부식을 0~10% 촉진하여 부착력을 평가하였다. 또한 FRP Hybrid Bar는 에폭시 코팅으로 인해 보통 상태에서는 부식 진전이 매우 작으므로 notch를 인위적으로 가하여 OPC 콘크리트에 매립시켰으며, 이후 부식실험을 수행하였다. 실험 결과, 부식된 철근의 부착력이 21% 수준으로 감소해도 FRP Hybrid Bar에 발생된 notch는 부착력에 큰 영향이 없는 것으로 평가되었다. 또한 GGBFS 콘크리트를 사용한 부재의 경우, 통과 전류가 감소하여 일반철근을 사용해도 70%이상의 부착력을 유지하고 있었다.

• 한국건축시공학회지
• /
• 제22권2호
• /
• pp.149-160
• /
• 2022

본 연구에서는 국내에서 생산되는 목재와 접착제를 활용한 Glued-in rod 접합부의 인발성능을 평가하고자 접착제의 종류, 철근의 매입깊이 및 매입방향을 고려한 인발성능 실험연구를 수행하였다. 실험결과, 액상형 접착제 사용 실험체가 더 우수한 인발성능을 보여주었으며, 철근의 매입깊이가 길어질수록 철근의 항복을 먼저 유도하여 높은 최대 인발하중을 보여주었다. 인발성능 실험결과를 통하여 철근의 항복강도보다 접착제의 부착강도를 더 강하게 설계하는 것이 유리한 Glued-in rod 접합부 설계식을 제안하였으며, 접착제의 부착강도의 시공오차를 고려한 보정계수 0.75 또한 제안하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.647-652
• /
• 2000

The bond strength of latex-modified concrete to normal portland cement concrete measured with direct pull-out test. Using $250\times1100\times1400$mm concrete slab as the base concrete, an overlay of the latex-modified concrete is applied and cured similar to bridge deck and then tested in direct pull-out. The test results not only give values of the bond strength of the overlay tested but also clearly indicate whether the failure is in the bond interface or the materials tested.

• 오토저널
• /
• 제9권2호
• /
• pp.34-46
• /
• 1987

The drive efficiency is investigated with drawbar pull test to provide the basic data in the gradability and acceleration of the wheeled vehicle. As a result, the drive efficiencies are determined from 4*2 drive : Direct gear 0.89 1st gear 0.81 Other gears 0.83-0.87 4*4 high drive : Direct gear 0.85 1st gear 0.77 Other gears 0.79-0.83 4*4 low drive : Direct gear 0.83 1st gear 0.75 Other gears 0.77-0.81

• 한국지반공학회논문집
• /
• 제29권1호
• /
• pp.121-133
• /
• 2013

본 논문에서는 사질토에서 스크류 앵커 파일의 인발 저항 특성에 대한 실험적 내용을 다루었다. SAP에 대한 소개 및 적용분야 등의 간략한 설명을 시작으로 스크류 파일의 인발저항특성에 대한 이론적 배경들과 축소모형실험의 수행 방법에 대해 소개하였다. 조밀한 모래조건과 느슨한 모래조건에서 스크류 앵커 파일의 인발저항특성을 분석하기 위해 스크류 사이의 간격인 피치와 스크류의 직경을 변화시켜 실험을 수행하였고, 스크류 앵커 파일의 파괴 메커니즘에 근거한 이론적 인발특성에 관한 기존연구들을 검토하여 비교하였다. 연구결과 조밀한 모래조건과 느슨한 모래조건 모두에서 피치의 변화에 따른 인발저항력의 차이는 매우 미미하였고, 직경의 변화에 따라 인발 저항력이 상대적으로 많이 증가함을 확인할 수 있었다. 본 논문에서는 실험결과를 사질토에서 스크류 앵커 파일의 인발저항특성을 파악할 수 있도록 제시하였으며 기존의 이론식과 비교하여 실무적 관점에서의 검토 내용을 기술하였다.

• 한국기계가공학회지
• /
• 제18권4호
• /
• pp.16-25
• /
• 2019

Recently, due to labor shortages in rural areas within South Korea, the demand for upland-field machinery is growing. In addition, there is a lack of development of systematic performance testing of upland-field machinery. Thus, this study examined structural safety and drawbar pull based on soil properties, as a first step for systematic performance testing on the test bed. First, the properties of soil samples from 10 spots within the experimental site were examined. Second, the strain was measured and converted into stress on 8 points of an onion harvester that are likely to fail. More specifically, the chosen parts are linked to the power, along with the drawbar pull, using a 6-component load cell equipped between the tractor and the onion harvester. The water content of the soil ranged between 5.7%-7.5%, and the strength between 250-1171 kPa. The test soil was subsequently classified into loam soil based on the size distribution ratio of the sieved soil. The onion harvester can be considered as structurally safe based on the derived safety factor and the drawbar pull of 115-1194 kgf, according to the working speed based on agricultural fieldwork.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.944-955
• /
• 2009

In this thesis the model tests were performed to the pull-out characteristics of a suction pile subjected to a pull-out in sands. For this model tests, three different soil conditions ($D_r$=45, 65, 82%), three pile diameters (D=100, 150, 200mm) and three pile lengths (L=100, 150, 200mm), were changed. And the experimental results were also compared with those by the theoretical methods. The results by the experimental and theoretical analysis are as follows. The ultimate pull-out resistances increased as the relative density of sands, pile diameter, length and the ratio of pile length to diameter increased. The ultimate pull-out resistance by Meyerhof method(1973) overestimated that by the model test, but the results using the soil-pile friction angle suggested by Aas(1966) in the Meyerhof(1973) method were in good agreement with the experimental results.

• Journal of Biosystems Engineering
• /
• 제14권2호
• /
• pp.67-79
• /
• 1989

This study was conducted to investigate the applicability of true model theory for pull prediction in a powered lugged wheel-soil system and to examine the possibility of using principles of similitude in investigating the dimensions of soil parameters pertinent to a powered lugged wheel-soil system concerning the pull prediction. The following conclusions were derived from the study; 1) The pull of prototype wheels proved to be predicted by those of the model wheels for the range of the dynamic weight tested. The pull curves of models and prototype were respectively very similar in the shape. From this basic knowledge, it was enabled to apply the similitude theory to the performance prediction of the true model. 2) A conditional equation which can be used for the prediction of pull of prototype by model test was derived as follows. $n_f=n_1^{-b}$ where $n_f$ : force scale = $w/w_m$ $n_1$ : length scale = ${\ell}/{\ell}_m$ b : exponent on the length dimension of the soil property ${\alpha}$ The range of the numerical value of b, which was determined by the least square method, was found to be -2.0~-2.6. 3) Considering a relatively wide variation of b values in the pull prediction, b is considered to be a function of many variales. Thus it was concluded that there are several soil properties which are pertinent to the powered lugged-wheel-soil system concerning the pull prediction, and these soil properties may have the different effects on the pull of model and protytype wheels, to give the different dimension on the soil parameters.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.502-509
• /
• 1998

The scheme to reduce jerking phenomena in one push-pull type trainset was proposed. To simulate the jerking between coaches, dynamic analysis model was made. This model could analyze longitudinal dynamic behavior between locomotives and coaches caused by spring and damping characteristics of couplers and center pivots; characteristic curves of traction and braking. To validate the analysis results, tests were conducted in the same driving and braking condition. Comparison of longitudinal acceleration between simulation and test results shows a good agreement. To minimize the jerking phenomena, lots of dynamic simulations were conducted with varying driving/braking effort curve. From the results of simulations, an efficient and economic way to reduce jerking phenomena was found to be to reduce slope of tractive effort curve and synchronize braking time between locomotives and coaches. Test results show that this way could reduce the jerking Phenomena. To express jerkins Phenomena quantitatively, maximum peak to peak values of acceleration were used.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.788-795
• /
• 2005

In this study, the progressive failure and creep of the traditional ground anchor structure were decreased and a new ground anchor that can attain the required pull-out resistance even in soft sandy soils with low confining pressure was developed. Ground anchors are classified depending on the kind of stress the grout is subjected. If the grout material is subjected to tension then it is classified as tension anchor while when the grout material is subjected to compression it is classified as compression anchor. The ground anchor that possesses both the tension and compression mechanism mentioned above is known as composition anchor. It is the objective of this study to develope this type of composition anchor. The structure of the newly developed ground anchor was presented. Pull-out test in different types of soil and the behaviour during Pull-out test was also presented.