• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.17 no.32
• /
• pp.155-162
• /
• 1994

The Japanese "Just-In-Time" technique reduces inventory and unnecessary factors. This technique makes the success of Japanese firms, therefore many Korean firms try to apply it to their situation. But the technique doesn't bare the same success in Korean firms. This paper, therefore, considers the different situations between Korean rim and Japanese firm, then simulates the Pull system and Push system for a multiline, multistage production system. This paper drives the different results of simulation according to variable processing times, variable demand, set-up time and shortages in Pull system and Push system using GPSS. The results show that the performance of Pull system is lower than Push system's in variable master production scheduling and variable processing times.ing times.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.597-600
• /
• 2003

The development and maintenance of a sound bond are an essential requirements of concrete repair and replacement. The bond property of a bonded overlay to its substrate concrete during the lifetime is one of the most important performance requirements which should be quantified. A standard or a verified bond strength measurement method is required at field for screening, selecting materials and quality control for overlay or repair materials. This study compares the nipple pipe direct tensile test, flexural adhesion test, and core pull-off test with their test results. Substantial differences in the failure stresses of three test methods were attributed to their different geometries and loading conditions. From these comparison and investigation, core pull-off test was relatively good because the coefficient of variation values were about 2%. It would be suitable for use in-situ because of its simplicity and accuracy.

• Journal of electromagnetic engineering and science
• /
• v.7 no.4
• /
• pp.175-182
• /
• 2007

In this paper, a study on the reflector type frequency doubler, to suppress the undesired harmonics, is presented. A 12 to 24 GHz reflective frequency doubler is simulated and experimented. Design procedure of the frequency doubler with reflector is provided and the frequency doubler with good spectral purity is fabricated successfully. It has harmonic suppression of the $40{\sim}50\;dBc$ in the $1^{st}$ harmonic and the $50{\sim}60\;dB$ in the $3^{rd}$ harmonic with no additional filter. And, it has conversion gain with the input power of 0 dBm over bandwidth of 500 MHz. A NEC's ne71300(N) GaAs FET is used and the nonlinear model(EEFET3) using IC-CAP program is extracted for harmonic load pull simulation. Good agreement between simulated and measured results has been achieved.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.102-111
• /
• 2017

An automobile ball joint is the element for connecting the control arm and the knuckle arm, allowing rotational motion. The ball joint consists of the stud, plug, socket, and seat. These components are assembled through the caulking process that consists of plugging and spinning. In the existing research, the pull-out strength and gap stiffness were calculated, but we did not consider the uncertainties due to the numerical analysis and production. In this study, the uncertainties of material property and tolerance are considered to predict the distributions of pull-out strength and gap stiffness. Also, pull-out strength and gap stiffness are predicted as the a distribution rather than one deterministic value. Furthermore, a robust design applying the Taguchi method is suggested.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.242-248
• /
• 2012

Self oscillating current fed push pull resonant inverters can be controlled without using special drivers. Dc current flows through the choke coil and the power switches, although the driving signals of the power switches are sinusoidal. When the base current is near zero, the transistors cannot be operated in switching mode. Hence higher switching power losses and instantaneous peak power during off transitions are observed. In this study, an alternative design has been proposed to overcome this problem. A prototype circuit has been built which provides dc bias current to the base of the transistors. Experimental results are compared with theoretical calculations to demonstrate the validity of the design. The proposed design decreases the peak and average power losses by about 8 times, when compared to conventional designs.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1969-1971
• /
• 2002

This paper presents the design and performance of low pull-in voltage MEMS switches for commercial cellular/PCS applications. The switches have all-metal (3 ${\mu}m$ thick Au) movable plates over CPW(Coplanar Waveguide) transmission line. The stress gradient in a movable plate is considered in mechanical design to obtain an accurate pull-in voltage. Series metal-to-metal contact switches are fabricated and evaluated. Those switches exhibit the low loss(<0.2 dB @1.9 GHz) with good isolation(55 dB @1.9 GHz).

• Journal of Korean Association for Spatial Structures
• /
• v.15 no.4
• /
• pp.65-72
• /
• 2015

To overcome the weakness of spread foundation in large space structure, the research of precast pile for replace spread foundation have been conducted. The new type of joint between PHC pile and steel column is named HAT Joint(Hollow hAlf-sphere cast-sTeel Joint). It connected PHC Pile by bolt that verification of bolt connection should be accomplished. In this paper, pull-out test and flexural performance for HAT Joint to verifying the bolt connection is explained. As a result, the pull-out and flexural capacities of bolt were checked to use in real structure. Furthermore, the equation of pull-out strength was proposed.

• The Academic Congress of Korean Shoulder and Elbow Society
• /
• 2009.03a
• /
• pp.159-159
• /
• 2009

Repeated pulling-out of a suture anchor in the lateral row despite repeated attempts at insertion during a rotator cuff repair is not uncommon with the suture-bridge technique, especially in patients with osteoporosis. We describe a simple procedure for dealing with the pull-out of a PushLock anchor in the lateral row using a suture anchor with a suture eyelet during rotator cuff repair applying the suture-bridge technique.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.268-271
• /
• 2003

연구지역에 설치된 3개 관정에서 추적자시험 방법 중 단공 주입-회수시험을 실시하였다. Push-pull 추적자시험 자료 분석 결과 종분산지수는 0.086~0.657m의 값을 가지며(Pickens and Grisak, 1981), 지하수 유동속도는 9.07$\times$$10^{-4}$6.14$\times$$10^{-3}$m/min의 값을 보인다(Hall and other, 1991). 또한 계산된 종분산지수와 지하수 유속을 이용하여 종분산계수(3.77$\times$$10^{-4}$ ~ 9.53$\times$$10^{-4}$ $m^2$/min)를 산정하였다. 추적자의 거동특성이 크고 작음을 비교할 수 있게 하는 특성변수(Characteristic property)는 분산지수이므로, 분산지수의 크고 작음에 따라서 추적자의 거동특성이 달라짐에 주의해야 한다..

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1321-1327
• /
• 2006

This paper presents the calculation of unbalanced magnetic pull (UMP) that causes rotor misalignment in induction motor. The excessive noise and vibration will be occurred by means of rotor misalignment. Angular misalignment of rotor will produce air-gap permeance wave which is function of axial and circumferential coordinate. In this paper, the UMP is calculated using permeance and magneto motive force (MMF) in the case of static and dynamic misalignment. Based on the percentage of misalignment, the result shows that the UMP and magnetic pressure are increased according to the increasing of misalignment. The UMP is occurred not only in It frequency component but also the others.