• Progress in Superconductivity and Cryogenics
• /
• v.21 no.1
• /
• pp.18-24
• /
• 2019

This study was carried out to investigate the effect of milling of boron (B), which is one of raw materials of $MgB_2$, on the critical current density ($J_c$) of $MgB_2$. B powder used in this study is semi-amorphous B (Pavezyum, Turkey, 97% purity, 1 micron). The size of B powder was reduced by planetary milling using $ZrO_2$ balls (a diameter of 2 mm). The B powder and balls with a ratio of 1:20 were charged in a ceramic jar and then the jar was filled with toluene. The milling time was varied from 0 to 8 h. The milled B powders were mixed with Mg powder in the composition of (Mg+2B), and the powder mixtures were uniaxially pressed at 3 tons. The powder compacts were heat-treated at $700^{\circ}C$ for 1 h in flowing argon gas. Powder X-ray diffraction and FWHM (Full width at half maximum) were used to analyze the phase formation and crystallinity of $MgB_2$. The superconducting transition temperature ($T_c$) and $J_c$ of $MgB_2$ were measured using a magnetic property measurement system (MPMS). It was found that $B_2O_3$ was formed by B milling and the subsequent drying process, and the volume fraction of $B_2O_3$ increased as milling time increased. The $T_c$ of $MgB_2$ decreased with increasing milling time, which was explained in terms of the decreased volume fraction of $MgB_2$, the line broadening of $MgB_2$ peaks and the formation of $B_2O_3$. The $J_c$ at 5 K increased with increasing milling time. The $J_c$ increase is more remarkable at the magnetic field higher than 3 T. The $J_c$ at 5 K and 4 T was the highest as $4.37{\times}10^4A/cm^2$ when milling time was 2 h. The $J_c$ at 20 K also increased with increasing milling time. However, The $J_c$ of the samples with the prolonged milling for 6 and 8 h were lower than that of the non-milled sample.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.3
• /
• pp.227-235
• /
• 2016

This paper emphasized the necessity of the marine spatial planning (MSP) through the analysis of the major developmental projects which could make a contradiction based on the adequacy of the site selection and environmental impacts. The conflicting affairs between space utilization and management plan happen in the following ways: marine renewable energy development, sand mining, reclamation, construction of golf course in coastal area, thermal effluent and waste heat, erosion causing port development. The conflict of stakeholder continues caused by the accumulated environmental impact. For the reasons mentioned above, we found two things. First, it is necessary to comprehend the fact of developmental planning and MSP. Second, it is still unsatisfactory to connect the relevance of laws related to the spatial planning. For the reinforcement of marine environmental policy management, it is necessary to consolidate the property of site selection and assessment of developmental scale. Especially, while the strategic environmental assessment is in progress based on site selection and property of scale, consistent diagnosis is needed in the following concerns: the fact of the marine spatial planning, the relevance between national developmental plan and regional developmental plan, fisheries regulation, marine protected animals. For the environmentally sound and sustainable development (ESSD), MSP should have to be prepared based in a way of top-down including coastal and EEZ plan, relevance of ocean-use zoning and sector planning, 3-D spatial information. And also integrated information system have to be prepared through high-tech marine spatial information. In conclusion, consistent and relevant strategy for MSP should have to include the whole information related to the maritime affairs such as harbor, fishing port, fishing ground, coastal management, marine ecosystem generally.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.6
• /
• pp.1022-1026
• /
• 2012

To evaluate the application level of expeller cake fertilizer (ECF), we have investigated soil chemical properties, leaf mineral contents and yield of red mustard in plastic film greenhouse. Four levels of fertilizer were applied as 50% (ECF 50), 75% (ECF 75), 100% (ECF 100) and 150% (ECF 150) by base $1,848kg\;kg^{-1}$ of ECF. In 2010, red mustard was planted on April 28 in silt loam soil and harvested on July 7. Commerical yields were measured 12 times from May 14 to July 7. Electrical conductivity ($3.40{\sim}3.54dS\;m^{-1}$), available $P_2O_5$ ($580{\sim}618mg\;kg^{-1}$) and exchangeable cations ($K^+$, $Ca^{2+}$ and $Mg^{2+}$) were tended to increase by the application of ECF. However, the range of those was not so big increasing amount. The content of T-N, K, Ca and P of red mustard leaves was $63.2{\sim}66.4g\;kg^{-1}$, $55.1{\sim}56.4g\;kg^{-1}$, $8.6{\sim}9.5g\;kg^{-1}$ and $5.7{\sim}6.3g\;kg^{-1}$, respectively. The nitrogen utilization rate of red mustard was 38~52%, and it was decreased with increased application of ECF. The yield of red mustard was 13,670 to $14,460kg\;ha^{-1}$ on the basis of application amount of ECF and the yield did not increased in spite of increased ECF. The optimum dose of application of ECF for cultivation of red mustard was from $924kg\;ha^{-1}$ (ECF 50) to $1,386kg\;ha^{-1}$ (ECF 75). Environment-friendly and economical amount of applied fertilizer is more important than yield for cultivation of red mustard.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.4
• /
• pp.415-423
• /
• 2010

Pore network models are useful tools to investigate soil pore geometry. These models provide quantitative information of pore geometry from 3D images. This study presents a pore network model to quantify pore structure and hydraulic characteristics. The objectives of this work were to apply the pore network model to characterize pore structure from large images to quantify pore structure, calculate water retention and hydraulic conductivity properties from a three dimensional soil image, and to combine measured hydraulic properties from experiments with calculated hydraulic properties from image. Soil samples were taken from a site located at the Baltimore science center, which is located inside of the city. Undisturbed columns were taken from the site and scanned with a computer tomographer at resolutions of 22 ${\mu}m$. Pore networks were extracted by medial-axis transformation and were used to measure pore geometry from one of the scanned samples. Water retention and unsaturated hydraulic conductivity values were calculated from the soil image. Properties of soil bulk density, water retention and unsaturated hydraulic conductivity were measured from three replicates of scanned soil samples. 3D image analysis provided accurate detailed pore properties such as individual pore volumes, pore length, and tortuosity of all pores. These data made possible to calculate accurate estimations of water retention and hydraulic conductivity. Combination of the calculated and measured hydraulic properties gave more accurate information on pore sizes over wider range than measured or calculated data alone. We could conclude that the hydraulic property computed from soil images and laboratory measurements can describe a full structure of intra- and inter-aggregate pores in soil.

• Korean Journal of Environmental Agriculture
• /
• v.33 no.3
• /
• pp.149-154
• /
• 2014

BACKGROUND: To evaluate the application level of expeller cake fertilizer(ECF), we have investigated soil chemical properties, leaf mineral contents and yield of tah tasai Chinese cabbage in a plastic film greenhouse. METHODS AND RESULTS: Five levels of fertilizer were applied as 0%(ECF 0), 50%(ECF 50), 75%(ECF 75), 100% (ECF 100) and 150%(ECF 150) by base 1,848 kg/ha of ECF. In 2012, tah tasai Chinese cabbage was planted on April 28 in a silt loam soil and harvested on July 12. Commercial yields were measured 10 times from May 10 to July 12. Electrical conductivity (2.24~3.09 dS/m), available $P_2O_5$(484~581 mg/kg) and exchangeable cations($K^+$, $Ca^{2+}$ and $Mg^{2+}$) were tended to increase by the application of ECF. However, the range of those was not significant. The contents of T-N, K, Ca and P of tah tasai Chinese cabbage leaves were 62.2~66.5 g/kg, 44.3~48.7 g/kg, 5.1~5.9 g/kg and 5.6~6.2 g/kg, respectively. The nitrogen utilization rate of tah tasai Chinese cabbage was 39.4~51.6%, and it was decreased with increased application amount of ECF. The yield of tah tasai Chinese cabbage was 9,806 to 12,730 kg/ha on the basis of application amount of ECF and it was not increased in spite of increased ECF. CONCLUSION: The optimum dose of application of ECF for cultivation of tah tasai Chinese cabbage was ranged from 924 kg/ha(as ECF 50) to 1,386 kg/ha(as ECF 75). Environment-friendly and economical amount of applied fertilizer is more important than yield for cultivation of tah tasai Chinese cabbage.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.17-32
• /
• 2002

The purpose of this study was to find the rational method to analyze golf swing with specific property of club shaft. Three subjects were filmed by two high speed digital cameras with 500 fps. The phase analyzed was downswing of each subject. The three-dimensional coordinates of the anatomical landmarks were obtained with motion analysis system Kwon3d 3.0 version and smoothed by lowpass digital filter with cutoff frequency 6Hz. From these data, kinematic and kinetic variables were calculated using Matlab(ver 5.0) The variables for this study were angular velocity and accelerations, which were calculated and following conclusions have been made : 1) Golf swing time of stiff club is faster than that of regular club. 2) In shoulder joint motion of swing with the stiff club, x-stiff showed mort rapid negative acceleration than that of regular club. 3) In regular club, the velocity of club head would be more effective velocity, which was increasing, than those of other clubs before impact. 4) In wrist joint motion of swing with stiff club, x-stiff club showed faster than regular club in the downswing and impact more rapid negative acceleration.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.183-189
• /
• 2012

In this study, the cellular protective effect and antioxidative property of peanut sprout root extracts were investigated. Cellular protective effects of peanut sprout root extracts on the rose-bengal sensitized photohemolysis of human erythrocytes were investigated. The ethyl acetate fraction of extracts exhibited a cellular protective effect in a concentration dependent manner. Particularly, the aglycone fraction of extracts showed prominent cellular protective effects in a concentration range (5~50 ${\mu}g/mL$). They are more effective than that of (+)-${\alpha}$-tocopherol, known as a lipid peroxidation chain blocker. Reactive oxygen species (ROS) scavenging activities ($OSC_{50}$) of peanut sprout root extracts on ROS generated in $Fe^{3+}$-EDTA/$H_2O_2$ system were investigated using the luminol-dependent chemiluminescence assay. The ethyl acetate fraction of extracts ($OSC_{50}$; 1.59 ${\mu}g/mL$) showed a similar ROS scavenging activity compare with that of L-ascorbic acid (1.50 ${\mu}g/mL$), known as a strong antioxidant. On the other hand, the order of free radical (1,1-diphenyl-2-picrylhydraxyl, DPPH) scavenging activity ($FSC_{50}$) was (+)-${\alpha}$-tocopherol > 80% MeOH extract > aglycone fraction > ethyl acetate fraction. These results indicate that peanut sprout root extracts can function as an antioxidant in biological systems, particularly skin exposed to solar UV radiation by scavenging $^1O_2$ and other ROS, and to protect cellular membranes against ROS.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.12 s.138
• /
• pp.1596-1604
• /
• 2004

Quality Function Deployment(QFD) is a product development tool which ensures that the voice of the customer needs is heard and translated into products. To develop a sensible brassiere for middle-aged women QFD was adopted. In this study the applicability and usefulness of QFD was examined through the engineering design process for a sensible brassiere for middle-aged women. The customer needs for the wear comfort of brassiere was made by one-on-one survey of 100 women who aged 30-40. The customer competitive assessment was generated by wearing tests of 10 commercial brassieres. The subjective assessment was conducted in the enviornmental chamber that was controlled at $28{\pm}1^{\circ}C,\;65{\pm}3\%RH.$ As a results, we developed twenty-one customer needs and corresponding HOWs for the wear comfort of brassiere. The Customer Competitive Assessment was generated by wearing tests of commercial brassiere. The subjective measurement scale and dimension for the evaluation of sensible brassiere were extracted from factor analysis. Four factors were fitting, aesthetic property, pressure sensation, displacement of brassiere due to movement. The most critical design parameter was wire-related property and second one was stretchability of main material of brassiere. Also, wearing comfort of brassiere was affected by the interaction of initial stretchability of wing and support of strap. Engineering design process, QFD was applicable to the development of technical and aesthetic brassieres.

• International Commerce and Information Review
• /
• v.18 no.4
• /
• pp.263-281
• /
• 2016

The Importance of SEP (Standard Essential Patents) Procurement Operation is on the side of Governmental and Public both to accelerate the national trade negotiation competitiveness. To operate cooperative system of SEP creation and management, Government should monitor the effect and performance periodically to public sectors. and To achieve the support objectives, it should establish the virtuous circle infrastructure between R&D and economic performance on SEP. This can make the SEP enhancement to pursue the international competitiveness on Intellectual Property Rights. Especially the specific support approach to each phase of the SEP declaration matrix is essential to consolidate the possibility of SEP creation and acquisition. In this study, the concepts of SEP to accelerate the national trade negotiation competitiveness and the prior research were verified through the investigation of market trend and current state of affair analysis. Through the analysis of international and domestic situation of SEP procurement and management, We have found the results as follows. First of all, the leading conglomerates and the Government should focus on the secondary and tertiary industries to create and acquire SEPs to accomplish the effectiveness of selection and concentration. In second, the SMEs and Univ. Labs should focus on the quaternary sector of the economy to retain the competitiveness of speed and challenge on SEP related. From this study, the appropriateness of the tailored-support management model should be institutionalized, and the results implied an research in order to examine the suitability among the current SEP to enhance the competitiveness of national trade research issues.

• Microbiology and Biotechnology Letters
• /
• v.43 no.3
• /
• pp.195-203
• /
• 2015

Two bacterial strains, Bacillus licheniformis YB-1413 and YB-1414, producing extracellular α-galactosidase, were obtained from homemade Doenjang. On the basis of their biochemical properties, 16S rRNA sequences and random amplified polymorphic DNA patterns by polymerase chain reaction, they were found to be somewhat different from one another. α-Galactosidase productivities of the two isolates were increased by wheat bran, but drastically decreased by melibiose, raffinose and sucrose which were used as carbon sources. The enzyme productivities were increased by yeast extract as a nitrogen source with maximum levels of 1.87 U/ml for YB-1413 and 1.69 U/ml for YB-1414, respectively. The enzymes of both isolates exhibited maximum activity for hydrolysis of para-nitrophenyl-α-D-galactopyranoside (pNP-αGal) under reaction conditions of pH 6.0 and 45℃. Their hydrolyzing activities for pNP-αGal were drastically decreased by the addition of low concentrations of ribose and galactose. They were capable of hydrolyzing completely α-1,6 linked galactosyl residue in melibiose, raffinose and stachyose, which are known to be anti-nutritional factors in products of soybean and legume. In relation to the latter, the isolates YB-1413 and YB-1414 have potential applicability in improving soybean-fermented foods and the nutritional value of soybean feed.