• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.80-86
• /
• 2017

In this study, nitrogen functional groups were introduced on graphite fiber (GF) to modify their electrical properties, and heating properties were investigated according to the treatment conditions. GF was prepared by a thermal solid-state reaction at $200^{\circ}C$ for 2 h. Surface properties of the nitrogen doped GF were examined by XPS, and its resistance and heating temperature were measured using a programmable electrometer and thermo-graphic camera, respectively. The XPS result showed that the nitrogen functional groups on the GF surface were increased with increasing of urea contents, and the heating property of the GF was also improved as nitrogen functional groups were introduced. The maximum heating temperature of GF treated by urea was $53.8^{\circ}C$ at 60 V, which showed 55% improved heating characteristics compared to that of non-treated GF. We ascribe this effect to introduced nitrogen functional groups on the GF surface by thermal solid-state reaction, which significantly affects the heating characteristics of GF.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11C
• /
• pp.1077-1087
• /
• 2003

In this paper, we proposed an architecture of a cryptosystem with various operating modes for the network security and implemented in hardware using the ASIC library. For configuring a cryptosystem, the standard block ciphers such as AES, SEED and 3DES were included. And the implemented cryptosystem can encrypt and decrypt the data in real time through the wired/wireless network with the minimum latency time (minimum 64 clocks, maximum 256 clocks). It can support CTR mode which is widely used recently as well as the conventional block cipher modes such as ECB, CBC and OFB, and operates in the multi-bit mode (64, 128, 192, and 256 bits). The implemented hardware has the expansion possibility for the other algorithms according to the network security protocol such as IPsec and the included ciphering blocks can be operated simultaneously. The self-ciphering mode and various ciphering mode can be supported by the hardware sharing and the programmable data-path. The global operation is programmed by the serial communication port and the operation is decided by the control signals decoded from the instruction by the host. The designed hardware using VHDL was synthesized with Hynix 0.25$\mu\textrm{m}$ CMOS technology and it used the about 100,000 gates. Also we could assure the stable operation in the timing simulation over 100㎒ using NC-verilog.

• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.83-86
• /
• 2015

Nowadays the weapon systems are employed air bursting munition (ABM) as smart programmable 40 mm shells which have been developed in order to hit the target with programmed munition that can be air burst after a set distance in the battlefield. In order to improve the accuracy of such a bursting time, by measuring the speed of the munition from the barrel, weapon systems calculate the exact time of flight to the target and then the time information must be inputted to the munition. In this study, we introduce a device capable of detecting a shot at K4 40 mm automatic grenade. The shot is composed of a rotating copper band to convert linear motion into rotary motion when it passes through the barrel, the steel section is exert the effect of fragment and aluminum section to give fuze information. The aluminum section was used to detect munition using eddy current method. To measure muzzle velocity by means of non-contact method, two eddy current probes separated 10 cm was employed. Time interval between two eddy current probe detection times was used as muzzle velocity. The eddy current probe was fabricated U-shape Mn-Zn ferrite core with enamelled copper wire, and 200 kHz alternating current was used to detect inductance change. Measured muzzle velocity using the developed sensor was compared to the Doppler radar system. The difference was smaller than 1%.

• Korean Journal of Food Science and Technology
• /
• v.36 no.5
• /
• pp.693-700
• /
• 2004

Viscometry was applied to identify irradiated corn starch (CS), sweet potato starch (SS), and potato starch (PS) from non-irradiated controls using Brookfield DV-III programmable rheometer. Effects of starch suspension concentration (7.0-9.5%) and spindle speed (25-125 rpm) were investigated. Established optimal viscosity-measuring conditions showed the highest correlation coefficient between irradiation dose (0-6.0 kGy) and corresponding viscosities for CS, SS, and PS. Threshold values for identifying irradiated starches were suggested. Viscosities of all samples significantly decreased with increasing irradiation dose (p<0.05) and spindle speed, while increased as suspension concentration increased. Optimal conditions for suspension concentration and spindle speed were 7.5% (6.7%, d.b.) and 125rpm in CS, 8.5% (7.3%, d.b.) and 125 rpm in SS, and 9.0% (7.3%, d.b.) and 100rpm in PS, respectively. Under these measuring conditions, threshold values for discriminating unknown samples were 0.313, 0.345, and 0.811 for CS, SS, and PS in 1.5 kGy-irradiated samples, compared with 0.521, 0.798, and 1.693 in non-irradiated samples, respectively, enabling identification of irradiated from non-irradiated starches.

• Journal of Acupuncture Research
• /
• v.29 no.3
• /
• pp.1-8
• /
• 2012

Objectives : The purpose of this study was to compare the skin temperature changes by the rechargeable and programmable electronic moxibustion device(EMD) with the traditional combustible moxibustion device(CMD). Methods : Skin temperature changes in six healthy volunteers induced by CMD and EMD were measured with digital infrared thermal imaging(DITI). Heat stimulation was applied on $LI_4$ and $TE_5$, and skin temperature changes on each point were measured at baseline and per minute for total 7 minutes, 2 minutes of heat stimulation and 5 minutes of observation. Results : There was no significant difference in the skin temperature changes between CMD and EMD. The temperature on $LI_4$ with EMD was $32.3{\pm}1.3^{\circ}C$ at baseline, $34.0{\pm}1.3^{\circ}C$ at 1 minute after heat stimulation start, $34.6{\pm}1.2^{\circ}C$ at 2 minutes after, and from 3 minutes after heat stimulation, it maintained $32.6{\sim}32.8^{\circ}C$. Conclusions : Methods for measuring skin temperature changes induced by heat stimulation of moxibustion were established, and the possibility of effectiveness of the newly developed electronic moxibustion device was raised with this preliminary study. This study can contribute to the development of clinical research methodology for traditional Korean medicine.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.6
• /
• pp.42-48
• /
• 2002

The design, construction and performance test of a convenient multi-purpose irradiator is described. A multi-purpose irradiator using Cesium-137 has been developed for studies of low dose radiation effects in biology and for calibration of Thermo Luminescent dosimeter(TLD). During the operation, three rods of radioactive material which are 10cm in length revolve 180 degrees and irradiate biological samples, or TLD, and return to their shielded position, after the programmed time. A programmable Logic Controller(PLC) controls the sequence of operation, interlock, motor rotation and safety system. The rotation speed of biological samples can vary up to 20 RPM. A real time monitoring system was also incorporated to check and control the operation status of the irradiator. The capacity of the irradiation chamber was 4.5 liters. The isodose distribution at arbitrary vertical planes was measured by using film dosimetry. The dose-rate was 0.13 cGy/min in air and 0.11 cGy/min in water equivalent material in the case of Cesium-137. Range of activity was 2 Ci. The homogeneity of dose distribution in the chamber was ${\pm}$7%. The actual radiation level on the surface was within permissible levels. The irradiator had a maximum 0.35 mR/min radiation leakage on its surface.

• Journal of the Korean Institute of Gas
• /
• v.21 no.2
• /
• pp.32-40
• /
• 2017

Safety Instrumented Systems (SIS) have wide application area. They are of vital importance at process plants to detect the onset of hazardous events, for instance, a release of some hazardous material, and for mitigating their consequences to humans, material assets, and the environment. The integrated safety systems, where electrical, electronic, and/or programmable electronic (E/E/PE) devices interact with mechanical, pneumatic, and hydraulic systems are governed by international safety standards like IEC 61508. IEC 61508 organises its requirements according to a Safety Life Cycle (SLC). Fulfilling these requirements following the SLC can be complex without the aid of SIS supporting tools. This paper presents simple SIS support tool which can greatly help the user to implement the design phase of the safety lifecycle. This tool is modelled in the form of Android application which can be integrated with a Web-based data reading and modifying system. This tool can reduce the computation time spent on the design phase of the SLC and reduce the possible errors which can arise in the process. In addition, this paper presents an optimization approach to SISs based on cost measures. The multi-objective genetic algorithm has been used for the optimization to search for the best combinations of solutions without enumeration of all the solution space.

• Journal of Digital Convergence
• /
• v.12 no.10
• /
• pp.337-343
• /
• 2014

The PRT(Personal Rapid Transit) in material or immaterial guided tracks is operated automatically according to the needs of passengers with the optimal non-stop path from the source to the destination. In recent years, the personal rapid transit (PRT) system, which affords superior accessibility and ease of use, has been spotlighted as a new transport system for the future. In this study, a method for vertical lifting of PRT vehicles was proposed to facilitate interlink with other means of transport and thereby improve the efficiency of door-to-door transport. For this purpose, operation control interfaces were designed and experiments were conducted. Programmable Logic Controller (PLC) dedicated for the PRT vertical lift was designed to interface with Operation Control Center (OCC) by Modbus TCP over Ethernet. We implemented a 3D graphical PRT operation simulator which can emulate the mixing operation of the virtual vehicles and the actual vehicles.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.388-396
• /
• 2017

Since there are many variables such as various poses, illuminations and occlusions in a face detection problem, a high performance detection system is required. Although CNN is excellent in image classification, CNN operatioin requires high-performance hardware resources. But low cost low power environments are essential for small and mobile systems. So in this paper, the CPU-FPGA integrated system is designed based on 3-stage cascade CNN architecture using small size FPGA. Adaptive Region of Interest (ROI) is applied to reduce the number of CNN operations using face information of the previous frame. We use a Field Programmable Gate Array(FPGA) to accelerate the CNN computations. The accelerator reads multiple featuremap at once on the FPGA and performs a Multiply-Accumulate (MAC) operation in parallel for convolution operation. The system is implemented on Altera Cyclone V FPGA in which ARM Cortex A-9 and on-chip SRAM are embedded. The system runs at 30FPS with HD resolution input images. The CPU-FPGA integrated system showed 8.5 times of the power efficiency compared to systems using CPU only.

• Publications of The Korean Astronomical Society
• /
• v.21 no.2
• /
• pp.67-74
• /
• 2006

We have developed a control electronics system for an infrared detector array of KASINICS (KASI Near Infrared Camera System), which is a new ground-based instrument of the Korea Astronomy and Space science Institute (KASI). Equipped with a $512{\times}512$ InSb array (ALADDIN III Quadrant, manufactured by Raytheon) sensitive from 1 to $5{\mu}m$, KASINICS will be used at J, H, Ks, and L-bands. The controller consists of DSP(Digital Signal Processor), Bias, Clock, and Video boards which are installed on a single VME-bus backplane. TMS320C6713DSP, FPGA(Field Programmable Gate Array), and 384-MB SDRAM(Synchronous Dynamic Random Access Memory) are included in the DSP board. DSP board manages entire electronics system, generates digital clock patterns and communicates with a PC using USB 2.0 interface. The clock patterns are downloaded from a PC and stored on the FPGA. UART is used for the communication with peripherals. Video board has 4 channel ADC which converts video signal into 16-bit digital numbers. Two video boards are installed on the controller for ALADDIN array. The Bias board provides 16 dc bias voltages and the Clock board has 15 clock channels. We have also coded a DSP firmware and a test version of control software in C-language. The controller is flexible enough to operate a wide range of IR array and CCD. Operational tests of the controller have been successfully finished using a test ROIC (Read-Out Integrated Circuit).