• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.957-960
• /
• 2004

From a water-environmental point of view, with a change of understanding and concern about vegetation, it changes that vegetation acts as stability of channel and bed, providing habitats and feed for fauna, and means improving those with appreciation of the beautiful but resistant factor to the flow So, it becomes important concern and study subjects that turbulent structure by vegetation, shear stress and transport as well as roughness and average velocity by vegetation. But from a hydraulic point of view, vegetation causes resistance to the flow and can increase the risk of flooding, Therefore, this thesis concern the flow characteristics in vegetated open channels. According to the experimental results, $z_0$ was on an average $0.4h_p$ in a vegetated open channel. So, the elevation corresponding to zero velocity in a vegetated channel was the middle of roughness element. The limit for logarithmically distributed profile over the roughness element was from $z_0$ to $0.80h_{over}$ for a vegetated channel. Among the existing theory, the method of Kouwen et al.(1969), Haber(1982), and El-Hakim and Salama(1992) except Stephan(2001) gave a very good value compared to the measured velocity profile.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.2
• /
• pp.244-251
• /
• 2013

This paper presents a study the change of the load profile on the power system by the charging impact of electric vehicles (EVs) in 2020. The impact of charging EVs on the load demand is determined not only by the number of EVs in usage pattern, but also by the number of EVs being charged at once. The charging load is determined on an hourly basis using the number of the EVs based on different scenarios considering battery size, model, the use of vehicles, charging at home or work, and the method of charging, which is either fast or slow. Focusing on the impact of future load profile in Korea with EVs reaching up 10 and 20 percentage, increased power demand by EVs charging is analyzed. Also, this paper analyzes the impact of a time-of-use (TOU) tariff system on the charging of EVs in Korea. The results demonstrate how the penetration of EVs increases the load profile and decreases charging demand by TOU tariff system on the future power system.

• Journal of Magnetics
• /
• v.6 no.3
• /
• pp.86-89
• /
• 2001

Microstructure modifications are investigated for annealed Co-based amorphous ribbon in vacuum and open air. X-ray diffraction (XRD) spectra for annealed sample in vacuum indicate atomic arrangements with initial nucleation of hcp-Co crystallite at 38$0^{\circ}C$ annealing temperature. However, the XRD spectra in samples with long annealing times of $t_a\geq300$ min demonstrate sharp and good developed surface crystalline hcp-, fcc- Co and $Co_2$Si phases. The giant magnetoimpedance (GMI) profile at 0.1 MHz displaying one-peak behavior in vacuum annealed samples at T = 38$0^{\circ}C$ irrespective of annealing time $t_a$ from 20 to 480 mim. For the annealed samples in an open air, the GMI profile shows two-peaks for $t_a$ = 20 min annealed sample. However, one of peaks disappears and an asymmetric GMI profile exhibits a drastic step-like change near zero field for $t_a\geq300$min. Such asymmetric GMI characteristics is related to the surface microstructures of fcc-Co, hop-Co and $Co_2$Si crystalline phases.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.5
• /
• pp.405-411
• /
• 2011

This paper presents a hierarchical trajectory planning method which can handle a collision-free of the planned path in complex and dynamic environments. A PV (Path & Velocity profile) planning method minimizes a sharp change of orientation and waiting time to avoid a collision with moving obstacle through detour path. The path generation problem is solved by three steps. In the first step, a smooth global path is generated using $A^*$ algorithm. The second step sets up the velocity profile for the optimization problem considering the maximum velocity and acceleration. In the third step, the velocity profile for obtaining the shortest path is optimized using the fuzzy and genetic algorithm. To show the validity and effectiveness of the proposed method, realistic simulations are performed.

• Research in Community and Public Health Nursing
• /
• v.23 no.3
• /
• pp.231-243
• /
• 2012

Purpose: The purpose of this study was to identify the relationships between health status including objective health status and subjective health perception and Health-Promoting Lifestyle Profile II in North Korean immigrants. Methods: During August 2011 to November 2011, a convenience sample of 96 subjects aged 19 to 65 years were recruited from two centers and one public health center in Gyeongnam. The subjects were interviewed face to face by trained people with a survey questionnaire. Results: Approximately 40% of North Korean immigrants rated their health status as 'poor', and the prevalence of health problems in them was 81.3%. The average level of health-promoting lifestyle profile II was $1.78{\pm}0.35$. Females with normal weight or overweight, and have stayed for over 1 year in South Korea were related to the lower score of health-promoting lifestyle profile II. Conclusion: Considering North Korean immigrants' health background and health behaviors, customized health care program focusing on musculoskeletal disorder and psychological problems are required, and at the same time health behavior change program to achieve lifetime wellness should be developed.

• Journal of Animal Science and Technology
• /
• v.50 no.4
• /
• pp.561-572
• /
• 2008

Responses of real-time control parameters, such as ORP, DO and pH, to the conditions of biological animal wastewater treatment process were examined to evaluate the stability of real-time control using each parameter. Also an optimum index for supplemental carbon source addition based on NOx-N level was determined under a consideration of denitrification rate by endogenous respiration of microorganism and residual organic matter in liquor. Experiment was performed with lab-scale sequencing batch reactor(SBR) and working volume of the process was 45L. The distinctive nitrogen break point(NBP) on ORP-and DO-time profiles, which mean the termination of nitrification, started disappearing with the maintenance of low NH4-N loading rate. Also the NBP on ORP-and DO-time profiles was no longer observed when high NOx-N was loaded into the reactor, and the sensitivity of ORP became dull with the increase of NOx-N level. However, the distinctive NBP was constantly occurred on pH(mV)-time profile, maintaining unique profile patterns. This stable occurrence of NBP on pH(mV)-time profile was lasted even at very high NOx-N:NH4-N ratio(over 80:1) in reactor, and the specific point could be easily detected by tracking moving slope change(MSC) of the curve. Revelation of NBP on pH(mV)-time profile and recognition of the realtime control point using MSC were stable at a condition of over 300mg/L NOx-N level in reactor. The occurrence of distinctive NBP was persistent on pH(mV)-time profile even at a level of 10,000mg/L STOC(soluble total organic carbon) and the recognition of NBP was feasible by tracing MSC, but that point on ORP and DO-time profiles began to disappear with the increase of STOC level in reactor. The denitrfication rate by endogenous respiration and residual organic matter was about 0.4mg/L.hr., and it was found that 0.83 would be accepted as an index for supplemental carbon source addition when 0.1 of safety factor was applied.

• The korean journal of orthodontics
• /
• v.13 no.2
• /
• pp.193-199
• /
• 1983

The purpose of orthodontic treatment is to produce functional occlusion and to create or maintain facial esthetic harmony. The soft-tissue covering of the face also plays an important role in facial esthetics, speech and other physiologic functions. The study of the soft-tissue profile is important for the planning of orthodontic treatment. The author studied cephalometric X-ray films on 49 patients (23boys, 26 girls) with Angle's class II division 1 malocclusion, ranged from 9 to 13 years of age. Roentgenocephalmetric X-ray films were taken pre and post orthodontic care. Tracings were made in usual manner. The obtained results were as follow. 1. There was no significant sexual difference on mean changes. 2. In the comparison of the soft-tissue thickness changes, Ls-Ls' and Si-Si' in male subjects were remarkable. 9. There were significant correlations between osseous (Ss') change and soft-tissue (Ss) chang, of maxilla in male and female subjects subsequent to orthodontic treatment. 4. The ratios between the protraction of the Ss' and that of the Ss were 1:1.5 in all sexes, the ratios between the Si' and that of the Si were 1:1.4 in male and 1:1.2 in female. 5. There were significant correlations between maxillary central incise. angulation change $({\angle}A)$ and upper lip inclination change $({\angle}B)$ in all sexes. 6. There were little correlations between change in distance difference of Is and Ii and change in distance difference of Ls and Li in all sexes in all sexes.

• Korean Journal of Clinical Pharmacy
• /
• v.10 no.3
• /
• pp.101-106
• /
• 2000

Menopausal women experience urogenitory and vasomotor symptoms with increased risk of osteoporosis and cardiovascular diseases, which can be reduced by hormone replacement therapy. However unopposed estrogen therapy has been associated with an increased risk of endometrial hypeiplasia or cancer. The objectives of this study were to compare effects of continuous vs. sequential hormone replacement therapy (HRT) on lipid profile, bone mineral density and menopausal symptoms of postmenopausal women and to assess how they perceive the menopause and HRT culturally. In this retrospective study, women in menopause longer than 6 months, normal in the mam-mogram and Papanicolaou smear, cholesterol level lower than 190 mg/dL or triglyceride level lower 4han 500 mg/dL were treated with Srogen (conjugated equine estrogen 0.625 mg tablet) and Provera (medroxyprogesterone acetate 2.5 mg tablet) for continuous treatment(CT) or Cycloprogynova (Estradiol valerate 2 mg and Norgestrel 0.5 mg complex tablet) for sequential treatment(ST). They were evaluated for lipid profile, bone mineral density, menopausal symptoms, side effects and their perception of menopause and HRT. As results, total sixty-seven patients out of ninety-four enrollees were included in final analysis (33 in continuous therapy, 34 in sequential therapy). There were significant decrease in total cholesterol ($15.04\pm3.17$, p=0.0001), LDL ($19.72\pm3.27$, p=0.0001), and increase in HDL ($5.89\pm1.63$, p=0.0001). Bone minora) density increased significantly with HRT ($0.02\pm0.11$, p=0.0001). But, there were no significant differences in change of lipid profile between continuous and sequential therapy: Total cholesterol, $13.12\pm4.7\;vs.\;16.91\pm4.3;\;LDL\;20.53\pm4.1\;vs.\;18.93\pm5.12:HDL\;7.15\pm2.3\;vs.\;4.67\pm2.2,\;p>0.05$. Incidences of flush reduced from $75\%\;(CT)\;to\;3.13\%\;and\;71.88\%\;(ST)\;to\;9.35\%$. The change of endometrium and breast were found 3 (CT) and 5 (ST) women, respectively. Most of women recognized that HRT is necessary $(70\%)$ for postmenopausal period but did not understand well the cardiovascular protective effect. In conclusion, hormone replacement therapy was effective in improving lipid profile, bone mineral density and menopausal symptoms in both continuous and sequential treatments with similar efficacy.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.2
• /
• pp.145-149
• /
• 2017

One of the challenges facing precision manufacturers is the increasing feature complexity of tight tolerance parts. All engineering drawings must account for the size, form, orientation, and location of all features to ensure manufacturability, measurability, and design intent. Geometric controls per ASME Y14.5 are typically applied to specify dimensional tolerances on engineering drawings and define size, form, orientation, and location of features. Many engineering drawings lack the necessary geometric dimensioning and tolerancing to allow for timely and accurate inspection and verification. Plus-minus tolerancing is typically ambiguous and requires extra time by engineering, programming, machining, and inspection functions to debate and agree on a single conclusion. Complex geometry can result in long inspection and verification times and put even the most sophisticated measurement equipment and processes to the test. In addition, design, manufacturing and quality engineers are often frustrated by communication errors over these features. However, an approach called profile tolerancing offers optimal definition of design intent by explicitly defining uniform boundaries around the physical geometry. It is an efficient and effective method for measurement and quality control. There are several advantages for product designers who use position and profile tolerancing instead of linear dimensioning. When design intent is conveyed unambiguously, manufacturers don't have to field multiple question from suppliers as they design and build a process for manufacturing and inspection. Profile tolerancing, when it is applied correctly, provides manufacturing and inspection functions with unambiguously defined tolerancing. Those data are manufacturable and measurable. Customers can see cost and lead time reductions with parts that consistently meet the design intent. Components can function properly-eliminating costly rework, redesign, and missed market opportunities. However a supplier that is poised to embrace profile tolerancing will no doubt run into resistance from those who would prefer the way things have always been done. It is not just internal naysayers, but also suppliers that might fight the change. In addition, the investment for suppliers can be steep in terms of training, equipment, and software.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.133-141
• /
• 2000

Standardization EMU in comparison with the existing EMU has been largely changed the material and section profile of the structure as the Aluminium made. This study is analytically predicted the influence of inner noise in tunnel running when the above change is made.