• 한국대기환경학회지
• /
• 제24권5호
• /
• pp.512-522
• /
• 2008

Ammonia is a major compound of odor in livestock house. To enhance the performance of ammonia oxidation (decomposition). the gas-liquid, two phase photocatalytic oxidation system was designed and prepared in this study. Commercial P-25 as $TiO_2$ catalyst was used for ammonia decomposition. V/P-25 catalyst prepared by sol gel method was also used for the removal of by-producted $NO_x$ in $NH_3$ oxidation reaction. When $TiO_2$ was used as a photocatalyst, the conversion to $N_2$ in ammonia decomposition reached above 90% until 200hr (The air flow rate of 4L/min with the ammonia concentration up to 25ppm.). However, considerable amounts of NO and $NO_2$ were formed as a result of $NH_3$ oxidation (as a by-product). Therefore, we added Vanadia impregnated $TiO_2$(P-25) catalyst for the removal of $NO_x$ at the end of reaction trail. The results of a pilot-scale operation were successful to achieve the simultaneous removal of $NH_3\;and\;NO_x$ about 81 and 87%, respectively.

• 한국분말재료학회지
• /
• 제12권3호
• /
• pp.186-191
• /
• 2005

A formation of aluminum hydroxide by hydrolysis of nano and micro aluminum powder has been studied. The nano aluminum powder of 80 to 100 nm in diameter was fabricated by a pulsed wire evaporation (PWE) method. The micro powder was commercial product with more than $10\;{\mu}m$ in diameter. The hydroxide type and morphology depending on size of the aluminum powder were examined by several analyses such as XRD, TEM, and BET. The hydrolysis procedure of micro aluminum powder was different from that of nano aluminum powder. The nano aluminum powder after immersing in the water was transformed rapidly to a nano fibrous boehmite, accompanying with a remarkable temperature increase, and then further transformed slowly to a stable bayerite. However, the micro powder was changed to the stable bayerite slowly and directly. The formation of fibrous aluminum hydroxide from nano aluminum powder might be due to the fine cracks which were formed by hydrogen gas pressure on the surface hydroxide layer during hydrolysis. The nano powder with large specific surface area and small size reacted more actively and faster than the micro powder, and transformed to meta-stable hydroxide in relatively short reaction time. Therefore, the formation of fibrous boehmite is special characteristic of hydrolysis of nano aluminum powder.

• 한국융합학회논문지
• /
• 제4권1호
• /
• pp.1-7
• /
• 2013

본 연구는 자전거 안전 시스템 장치 개발에 관한 연구과제로 대상기술의 개요, 기술개발의 필요성 및 성공 시 파급효과, 기술개발의 목표, 개발방법, 기술개발 성공 시 판매 수출 등 사업화 방법, 시작품 성능 및 제원(speculation)에 대해 다음과 같은 연구 계획을 가지고 추진하였다. 대상기술(제품)의 개요는 이동시 안전운행을 위한 장치의 개발 및 고가의 자전거를 위한 보관 시 안전장치 개발에 있다. 기술개발의 필요성(기존의 애로사항 등) 및 성공 시 파급효과로는 자전거 보급 확대에 따른 이동량 증가에 따라 각종 안전사고 발생을 줄일 필요가 대두되었고, 욕구의 다양화로 고가의 자전거 보급이 늘어남에 따라 도난, 분실 등의 사고가 우려되어 개발하게 되었고, 안전사고를 미연에 방지하므로 부상치료, 재산손실에 대한 경제적 손실 억제하는 효과를 가지고 있다. 기술개발의 목표는 자전거 운행시 안전한 방향전환을 위한 시그널장치, LED 헤드라이트와 도난을 대비한 도난방지 시스템을 사용자가 별도의 도움 없이 혼자서 손쉽게 장착할 수 있는 장치를 개발하는데 있다.

• Journal of Astronomy and Space Sciences
• /
• 제14권2호
• /
• pp.297-311
• /
• 1997

산소 기체($O_2$)를 전기 방전에 의해 완전히 오존($O_3$)으로 만든 후 $30~150^{\circ}C$범위의 온도에서 열분해 시켰다. 열분해 결과 얻어진 산소 기체를 동위원소 질량분석기로 분석하여 동위원소 분할효과를 측정하였다. 낮은 온도에서는 생성된 산소 기체가 오존에 의해 더 가벼우면서 질량에 의존하는 일반적인 동위원소 분할효과를 보이다가, $110^{\circ}C$ 이상의 실험에서는 산소 기체가 더 무거워지면서 $^{17}O$와 $^{18}O$가 $^{16}O$에 비해 같은 양 만큼씩 많아지는 질량과 무관한 분할효과를 나타냈다. 같은 재질(파이렉스)의 반응 관을 이용한 연구들과 그 범위와 경향이 거의 일치하였다. 실험 결과를 이용하여 산소 생성 비율이 일정한 값이 되는 순간의 동위원소 분할 인자들에 대한 값을 최소자승 법을 이용하여 구하였다. 관측된 현상들은 오존의 열분해 메커니즘의 이해와 운석 및 성층권에서의 산소 동위원소의 질량에 무관한 분포에 대한 이해에 중요한 역할을 할 것이다.

• 한국가시화정보학회지
• /
• 제17권3호
• /
• pp.24-31
• /
• 2019

Recently, an air-lift bio-reactor operated by micro bubbles has been utilized to product hydrogen fuel. To enhance the performance, characteristics of hydrodynamics inside the bio-reactor were analyzed using a numerical simulation for two-phase flow. An Eulerian model was employed for both of liquid and gas phases. The standard k-ε model was used for turbulence induced by micro bubbles. A Population Balance Model was employed to consider size distribution of bubbles. A hollow cylinder was introduced at the center of the reactor to reduce a dead area which disturbs circulation of CO bubbles. An appropriate diameter of the draft tube and hollow cylinder were optimized for better performance of the bio-reactor. The optimum model could be obtained when the cross-sectional area ratio of the hollow cylinder to the reactor, and the width ratio of the riser to the downcomer approached 0.4 and 3.5, respectively. Consequently, it is expected that the optimum model could enhance the performance of the bio-reactor with the homogeneous distribution and higher density of CO, and more effective mixing.

• 공업화학
• /
• 제10권3호
• /
• pp.432-437
• /
• 1999

폴리에틸렌 열분해실험을 반응기 크기가 $10cm^3$인 스테인레스 스틸 반응기에서 수행하였으며 이때 반응온도는 $390{\sim}450^{\circ}C$이었다. 열분해생성물인 반응생성물과 기체생성물을 분리하여 채취하였고 각 생성물의 분자량분포는 HPLC-GPC와 GC분석을 통해 얻었다. 열분해반응의 개시-종료, 전파-비전파반응, 즉 수소탈취반응, 사슬절단, 고분자물질과 라디칼과의 결합반응 등을 설명할 수 있는 random, specific 생성물의 분자랑분포에 대한 distribution balance식을 제안하였다. 말단절단 과정에 의해 저분자량의 비응축성 기체생성물 (C1~C5)이 생성되었으며 이 기체생성물의 평균분자량은 38이었다. 무작위절단과 말단절단의 속도매개변수 중의 하나인 활성화에너지는 각각 35, 17 kcal/mole 이었다.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.77-84
• /
• 2001

Measurements of local CO, $CO_2$, $O_2$, $N_2$, $C_3$H$_{8}$, NOx concentrations and flame temperature are made for partially premixed flame with and without acoustic excitation. The CO, $CO_2$, $O_2$, $N_2$, and $C$_3$H_8$ concentrations are determined by thermal conductivity detection (Gas-chromatograph) and NOx concentrations are determined by chemiluminescent detection (NOx analyser). To measure local sample concentration, sampling probe was made by quartz with inlet diameter of 0.25mm. In the case of excitation, the visual shape of the flame is changed from laminar flame to turbulent-like flame. The flame length is also reduced, and the flame width becomes broad. In the observation of emission concentration without acoustic excitation, meanwhile, the $CO_2$ and NOx concentrations peak at flame front where the mixture meets with surrounding air, and the CO concentration is increasing at maximum position of CO2 concentration and peaks at the centerline of the burner. In the case of acoustic excitation, the $CO_2$ concentration is widely occurred at nozzle of the burner and is higher relative to unexcitation. The CO concentration is much reduced, but NOx concentration is more increasing. And flame temperature is higher relative to unexcitation. These are caused by enhancing of mixing with surrounding air due to excitation. However, in the case of acoustic excitation, the total NOx concentration is reduced because of the shortened flame length which affects residence time.e.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.436-437
• /
• 2012

Double patterning technology (DPT) has been suggested as a promising candidates of the next generation lithography technology in FLASH and DRAM manufacturing in sub-40nm technology node. DPT enables to overcome the physical limitation of optical lithography, and it is expected to be continued as long as e-beam lithography takes place in manufacturing. Several different processes for DPT are currently available in practice, and they are litho-litho-etch (LLE), litho-etch-litho-etch (LELE), litho-freeze-litho-etch (LFLE), and self-aligned double patterning (SADP) [1]. The self-aligned approach is regarded as more suitable for mass production, but it requires precise control of sidewall space etch profile for the exact definition of hard mask layer. In this paper, we propose etch end point detection (EPD) in spacer etching to precisely control sidewall profile in SADP. Conventional etch EPD notify the end point after or on-set of a layer being etched is removed, but the EPD in spacer etch should land-off exactly after surface removal while the spacer is still remained. Precise control of real-time in-situ EPD may help to control the size of spacer to realize desired pattern geometry. To demonstrate the capability of spacer-etch EPD, we fabricated metal line structure on silicon dioxide layer and spacer deposition layer with silicon nitride. While blanket etch of the spacer layer takes place in inductively coupled plasma-reactive ion etching (ICP-RIE), in-situ monitoring of plasma chemistry is performed using optical emission spectroscopy (OES), and the acquired data is stored in a local computer. Through offline analysis of the acquired OES data with respect to etch gas and by-product chemistry, a representative EPD time traces signal is derived. We found that the SE-EPD is useful for precise control of spacer etching in DPT, and we are continuously developing real-time SE-EPD methodology employing cumulative sum (CUSUM) control chart [2].

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2003년도 가을 학술논문집
• /
• pp.207-214
• /
• 2003

원자력시설에서 방사성요오드 제거용으로 사용되는 TEDA 침착활성탄의 고온공정에서의 메틸요오드의 제거성능을 은이온제올라이트(AgX)와 상호 비교하였다. $30^{\circ}C~400^{\circ}C$ 온도범위에서 온도에 따른 메틸요오드의 흡착량 및 탈착후 잔존량을 측정한 결과, 비첨착활성탄의 흡착성능은 온도가 증가함에 따라 급격히 감소하지만 TEDA 침착활성탄의 흡착성능은 $100^{\circ}C$부근에서도 AgX와 거의 유사한 값을 나타내었고, 탈착후 잔존량은 $250^{\circ}C$까지도 비침착활성탄에 비하여 매우 높은 값을 유지하였다. 또한 $100^{\circ}C$ 이상의 고온공정에서 AgX 및 TEDA 침착활성탄을 충전한 고정층 파괴특성을 상호 비교하였으며, 반응 생성기체의 분석으로부터 AgX에 의한 메틸요오드 제거 메커니즘을 제안하였다.

• 열처리공학회지
• /
• 제10권3호
• /
• pp.181-187
• /
• 1997

TiAl intermetallic compound was candidated for the application to the high temperature materials such as a gas turbine exhaust valve in the automobile. However, this material dose not have ductility allowing to machinability to product. To improve the ductility, many researches conduct alloy design and heat treatment methods. We observed that the microstructure of TiAl varied with Ni, Mn elements as well as a heat treatment condition. In the case of Ni element addition, the TiAlNi intermetallic compound was precipitated at the grain boundary. When the heat treatment temperature increased from $1000^{\circ}C$ to $1300^{\circ}C$, the TiAlNi intermetallic compound was uniformly dispersed on the matrix. In the case of Mn element addition, the mixed duplex structure of ${\gamma}$-TiAl and lamellar(TiAl/$Ti_3Al$) was obtained with $1250^{\circ}C$ and $1300^{\circ}C$ heat treatment for 1 hour. When the heat treatment temperature increased from $1250^{\circ}C$ to $1300^{\circ}C$, the lamellar domain of the duplex structure was transformed near-lamellar structure.