• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.35-41
• /
• 1997

A series-fed microstrip array antenna of beamwidth $10^{\circ}$, squint angle $80^{\circ}$ and SLL -15 dB below is designed. Series-fed arrays are formed by interconnecting all the elements by high-impedance transmission lines and feeding the power at the first element and it is a traveling-wave antenna which is terminated with a matched load. Radiation patterns and impedance matching of the antenna are analyzed by Ensemble 4.0, which is a popular software package for designing printed antennas and arrays. The squint angle of beam can be controlled by the spacing between the elements. The major advantages of series-fed array antennas are that feed arangement is compact and the losses associated with the feeding network are less than those of a corporate feed type. The antennas are fabricated on the RT/Duroid Laminates of 62 mil thickness. The experimental results are very close to the specifications to be designed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.381-391
• /
• 2010

In this paper, a novel frequency reconfigurable active array antenna(RAA) system, which can be reconfigurable for three reconfigurable frequency bands, is proposed by using commercial RF MEMS switches. The MEMS switch shows excellent insertion loss, linearity, as well as isolation. So, the system performance degradation of the reconfigurable system by using MEMS switches can be minimized. The proposed frequency reconfigurable active antenna system is consisted with the noble frequency reconfigurable front-end amplifiers(RFA) with the simple reconfigurable impedance matching circuits(RMC), reconfigurable antenna elements(RAE), as well as a reconfiguration control board(RCB) for MEMS switch control. The proposed RAA system can be reconfigurable for three frequency bands, 850 MHz, 1.9 GHz, and 3.4 GHz, with $2{\times}2$ array of the RAE having broadband printed dipole antenna topology. The validity of the proposed RFA as well as RAA is also presented with the experimental results of the fabricated systems.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.894-900
• /
• 2004

There are many types of circularly polarized(CP) microstrip antenna elements, which are used as a good unit radiator. Since an advantage of CP antenna is no strict alignment requirements between Rx and Tx system, the printed antennas with circular polarization are very often used in numerous satellite and mobile radio systems. In order to realize the broad bandwidth of 3 dB axial ratio and impedance of CP microstrip antenna, complex feed structure and tri-plate patch element have been researched. This paper describes a design of wideband microstrip cross slot array antennas with circular polarization. The proposed antenna is composed of an open-ended microstrip feed line as a feeder and a cross slot as a radiator for circular polarization. To realize the wide bandwidth, tri-plate structure are considered and cross slot is electromagnetically coupled with feed line. Optimum parameters of 1-element cross slot antenna are analyzed and designed by method of moments. These parameters are also applied to may antennas design considered the mutual coupling between radiating elements. Right hand circular polarization(RHCP) and left hand circular polarization(LHCP) of the proposed antenna are easily controlled by asymmetrical cross slot structure and slot position. In 1-element and 15-element cross slot array antenna, the good axial ratio of 1 dB below and the broad bandwidth characteristics of antenna are obtained.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.583-584
• /
• 2006

Printing technology has begun to get into the spotlight in many ways due to the low cost effectiveness to existent semi-conductor process. It also has very useful application areas, not only paper printing but also patterning for LCD color tilter, Photovoltaic patterning, RFID antenna, OLED, and so on. In this study, an apparatus of gravure offset printing was developed for fine line width printing. The pattern was composed of $20{\mu}m$ size of continuous lines of which pitch size was $40{\mu}m$. The printed pattern shows that it is possible to make around $20{\mu}m$ line-width printing pattern. The roll-to-roll printing system for fine line-width printing based on primary experiment is presented. For testing of multi-layer printing, the system was designed to be capable of printing two different materials from each printing unit using gravure-offset printing method and have a function of alignment of two printed materials.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.3
• /
• pp.202-208
• /
• 2019

In this study, an active element pattern (AEP) of a printed dipole was analyzed in 1D and 2D arrays. First, an AEP of the printed dipole was obtained using the simulation in the 2D infinite array. The scan blindness in the 2D array occurred in the E-plane direction at around ${\pm}36^{\circ}$; however, it was barely observed in the 1D array. To analyze the cause of the scan blindness in the 2D array, the dispersion properties of a unit cell was obtained and compared with the scan blindness by frequency change. The difference between the scan blindness of the 1D and 2D arrays was clarified using the comparison of the Q value in the unit cell in the 1D and 2D arrays. Then, the coupling of the electric field in the E-plane direction was observed when nine elements were separated between the two ports in a linearly arranged dipole structure. Finally, the printed dipole array was fabricated, and an AEP was measured for the $11{\times}1$ and $11{\times}3$ sub arrays. The proposed theory was verified using these observations and by comparison with the simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1325-1332
• /
• 2009

In this paper, we design a 2.4 GHz bio-radar system that can detect human heartbeat and respiration signals with small size and improved noise performance using single circular-polarized antenna and phase-locked loop. The demonstrated bio-radar system consists of single circular-polarized antenna with $90^{\circ}$ hybrid, low-noise amplifier, power amplifier, voltage-controlled oscillator with phase-locked loop circuits, quadrature demodulator and analog circuits. To realize compact size, the printed annular ring stacked microstrip antenna is integrated on the transceiver circuits, so its dimension is just $40\times40mm^2$. Also, to improve signal-to-noise-ratio performance by phase noise due to transmitter leakage signal, the phase-locked loop circuit is used. The measured results show that the heart rate and respiration accuracy was found to be very high for the distance of 50 cm without the additional digital signal processing.

• Journal of electromagnetic engineering and science
• /
• v.17 no.3
• /
• pp.159-164
• /
• 2017

This article proposes a design of chipless RFID tag with dipole array structure that is fully printable using conductive ink. The proposed tags encode data based on spectral signature modulations. The reading range is considerably increased (2 m) while maintaining low transmission power (1 mW). Several prototype chipless RFID tags were fabricated and measured in the SHF and UHF bands. The proposed dipole array structure enhances the antenna gain of the passive tags and contributes to overcoming the low conductivity of conductive ink. In order to verify the utility of our proposal, the tags are manufactured on paper, using conductive ink, for the purpose of economic mass production.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.546-550
• /
• 2003

For dual-band operation, it can be done by loading two pair of narrow slots in the equilateral-triangular patch, one embedded close to the side edges of the patch and the other inserted at the bottom edge of the patch. The obtained two operating frequencies are of same polarization planes. The frequency ratio of the two operating frequencies is turnabled by varing the positions and lengths of the inserted slots at the bottom edge of the patch. In this paper, A single-feed equilateral-triangular microstrip patch with two pairs of narrow slot for dual-frequency operation is printed on the substrate(TMN-4 Rosers Co.) of the 60 miles. the antenna radiation characteristics are calculated by Ensemble ver. 5.0 software, and compared with the experimental results.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.171-171
• /
• 2006

In this presentation, we would like to report an inkjet printing method to produce 1 to 2 bit RFID tag working in the range of 6 to 28 MHz with or without transistors. The inkjet printing method especially for the formation of transistors, inductors, capacitors will be presented by the view of polymer chemistry. This presentation also includes the printing schemes for memory cell, ring oscillator, rectifier, antenna, and so forth for constructing RFID tag. I illustrate these strategies by describing recent my works on the formation of all SWNT-TFT and conducting polymer-silver nanocomposite inks that can be applied in the construction of electronic devices.

• Journal of the Korean Institute of Navigation
• /
• v.23 no.2
• /
• pp.61-66
• /
• 1999

It is being more and more difficult to suppress emissions from electronic products using PCB(Printed Circuit Board) to the limit. Therefore, the exact evaluation of the emission from PCB has been more important to reduce the required time and the cost at the design phase of the products, especially on board ship's equipments. This research has evaluated the emission radiated from PCB based on the theoretical approach of SDA(Spectral Domain Analysis), which is available to analyze microwave stripline, coplanar line, patch antenna, etc. According to the theoretical results, it has been clearly shown that the emission radiated from PCB is reduced as the thickness of PCB is thinner, the permittivity of PCB is higher, the length of stripline is shorter, and the frequency is lower.