• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.1
• /
• pp.47-56
• /
• 2011

This study was carried out to investigate the characteristics of the Hanji which had been used for movable types printing volumes of the Joseon Dynasty. A total 29 volumes which had printed with metal and wooden movable types, were examined on the physical properties, fiber morphology, and color reactions. The grammage of all of the Hanji which had been used for movable types printing volumes were $13.10-51.65g/m^2$ and on the average was $25g/m^2$. The apparent density of the Hanji was $0.23-1.65g/cm^3$ and on the average was $0.4g/cm^3$. In almost all movable types printing volumes, the Hanji had undergone Dochim which is a processing of printability improvement. Through the examination on fiber morphology and color reactions, Hanji was investigated into that all of those were made from paper mulberry bast fiber.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2008.04a
• /
• pp.60-74
• /
• 2008

일반적으로 종이 도공의 바인더로 사용되는 라텍스는 입자경이 작을수록 도공층이 부동화 되기 전에 도공층 내에서 원지 혹은 도공층 표면으로의 이동 특성이 강해져서 최종 도공지의 인쇄적성에 다양한 품질의 변화를 보일 수 있다. 라텍스는 원지와 접촉하는 순간부터 원지의 특성에 따라 원지 방향으로 1차 마이그레이션이 일어나고 건조공정의 건조조건(IR-Infra Red 혹은 Hot Air Dryer)에 따라 도공층 표면으로의 2차 마이그레이션이 일어나며 이로 인해 도공층 내에서 Z-방향으로 바인더 분포가 불균일하게 분포하게 됨으로서 인쇄 모틀 현상에도 영향을 미치게 된다. 따라서 본 논문에서는 도공액의 농도와 라텍스의 입자경 그리고 건조조건에 따른 도공층의 구조변화가 최종인쇄적성에 미치는 상관성을 검토하였다.

• Advances in concrete construction
• /
• v.11 no.2
• /
• pp.141-149
• /
• 2021

This study is a basic research for evaluating the buildability of cementitious materials for three-dimensional (3D) printing. In the cement paste step, the thixotropy behavior according to the resting time, which represents the time interval between each layer, was analyzed. In addition, the relationship between the thixotropy behavior and 3D concrete printing buildability was derived by proposing a measurement method that simulates the 3D concrete printing buildup process. The analysis of the tendency of the thixotropy behavior according to the resting time revealed that the area of the hysteresis loop (AHyst) showed a tendency to increase and then converge as the resting time increased, which means hysteresis loop approach critical resting time for sufficient buildability. In the thixotropy behavior analysis that simulates the 3D concrete printing buildup process, the buildup ratio, which is the recovery rate of the shear stress, showed a tendency to increase and then converge as the resting time increased, which are similar results like hysteresis loop. It was concluded that AHyst and the buildup ratio can be used as parameters for determining the resting time, and they have close relationships with 3D concrete printing buildability.

• Journal of Powder Materials
• /
• v.29 no.2
• /
• pp.132-151
• /
• 2022

The CoCrFeMnNi high-entropy alloy (HEA), which is the most widely known HEA with a single face-centered cubic structure, has attracted significant academic attention over the past decade owing to its outstanding multifunctional performance. Recent studies have suggested that CoCrFeMnNi-type HEAs exhibit excellent printability for selective laser melting (SLM) under a wide range of process conditions. Moreover, it has been suggested that SLM can not only provide great topological freedom of design but also exhibit excellent mechanical properties by overcoming the strength-ductility trade-off via producing a hierarchical heterogeneous microstructure. In this regard, the SLM-processed CoCrFeMnNi HEA has been extensively studied to comprehensively understand the mechanisms of microstructural evolution and resulting changes in mechanical properties. In this review, recent studies on CoCrFeMnNi-type HEAs produced using SLM are discussed with respect to process-induced microstructural evolution and the relationship between hierarchical heterogeneous microstructure and mechanical properties.

• Food Science of Animal Resources
• /
• v.44 no.2
• /
• pp.225-238
• /
• 2024

3D printing technology enables the production of creative and personalized food products that meet consumer needs, such as an attractive visual appearance, fortification of specific nutrients, and modified textures. To popularize and diversify 3D-printed foods, an evaluation of the printing feasibility of various food pastes, including materials that cannot be printed natively, is necessary. Most animal resources, such as meat, milk, and eggs, are not inherently printable; therefore, the rheological properties governing printability should be improved through pre-/post-processing or adding appropriate additives. This review provides the latest progress in extrusion-based 3D printing of animal resource-based inks. In addition, this review discusses the effects of ink composition, printing conditions, and post-processing on the printing performance and characteristics of printed constructs. Further research is required to enhance the sensory quality and nutritional and textural properties of animal resource-based printed foods.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.11
• /
• pp.987-992
• /
• 2014

Register control of roll-to-roll printing system for printed electronics requires accurate measurement of register errors. The register marks used for the recognition of patterns position between layers have inherently defects due to low printability of register marks themselves, which brings out inaccurate register accuracy and consequently low performance of printed electronics devices. In this study, the compensation methods for the unrecognized or missing register data are proposed to improve the recognition and consequently the control performance of register accuracy in roll-to-roll printing equipment. The compensation methods using the prior data and the linear interpolation are proposed and compared with the case without compensation for the simulation as well as experiment. Only the linear interpolation method could successfully compensate the missing data and consequently improve the register control performance. We should apply the compensation process of the register errors to improve the register control accuracy in the roll-to-roll printing equipment.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.53.2-53.2
• /
• 2010

In this study, we focused on our specialized electrode process for Si back-contact crystalline solar cell. It is different from other well-known back-contact cell process for thermal aspect and specialized process. In general, aluminum makes ohmic contact to the Si wafer and acts as a back surface reflector. And, silver is used for low series resistance metal grid lines. Aluminum was sputtered onto back side of wafer. Next, silver is directly patterned on the wafer by screen printing. The sputtered aluminum was removed by wet etching process after rear silver electrode was formed. In this process, the silver paste must have good printability, electrical property and adhesion strength, before and after the aluminum etching process. Silver paste also needs low temperature firing characteristics to reduce the thermal budget. So it was seriously collected by the products of several company of regarding low temperature firing (below $250^{\circ}C$) and aluminum etching endurance. First of all, silver pastes for etching selectivity were selected to evaluate as low temperature firing condition, electrical properties and adhesive strength. Using the nano- and micron-sized silver paste, so called hybrid type, made low temperature firing. So we could minimize the thermal budget in metallization process. Also the adhesion property greatly depended on the composition of paste, especially added resin and inorganic additives. In this paper, we will show that the metallization process of back-contact solar cell was realized as optimized nano-paste characteristics.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.47-52
• /
• 2003

A new type of Bi based glass frit was developed for Ag paste in PDP applications and its properties are compared with the commercially used Pb based glass frit. After optimization of the properties of Bi based frits for PDP application such as the softening temperature and the coefficient of thermal expansion (C.T.E), the screen printed electrodes prepared with the Bi based fit contained Ag paste were characterized. In $Bi_2O_3-B_2O_3-Al_2O_3$ glass system with the more than 50% of $Bi_2O_3$, the softening temperature, the thermal expansion coefficient and the line resistivity was 400∼$480^{\circ}C$, 7.31∼$10.02\times 10^{-6}/^{\circ}C$> and 4.1∼4.8$\Omega$ respectively. Properties of the Bi based frits are comparable with the Pb based frits. A printability and an uniformity of the Bi based frits were excellent in screen printed Ag eletrode. The Bi based frit system is an excellent candidate material for Pb free and Alkali free frit in PDP applications.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.1-10
• /
• 2014

In papermaking industry, inorganic fillers are widely used for the purpose of improving opacity, brightness, printability, uniformity and dimensional stability. They are also useful for production costs and energy savings. In the past, inorganic fillers in papermaking industry only focused on micro-scale but recently, new trials on nano-powdered technology are applying. Even nano-powdered fillers are rapidly utilized for improving the optical and surface properties in coating and surface sizing, there still have some problems in wet-end process due to poor dispersibility and retention. In this study, nano-particled calcium carbonate was produced by milling the PCC and its applicability between micro sized and nano sized calcium carbonated was compared in wet-end process, and finally the sheet properties were evaluated. Nano-PCC was not retained in sheet structure without applying retention system, but with retention system nano-powdered PCC was absorbed on fiber surface with expanding the fiber networks. The application of PAM-bentonite system has resulted in high ash retention and bulky structure for copier paper, and good optical properties in brightness and opacity. However, it required to solve the weakness of low tensile property due to interruption of hydrogen bonding by nano fillers.

• Advanced Composite Materials
• /
• v.18 no.4
• /
• pp.315-326
• /
• 2009

PCC (precipitated calcium carbonate) and ground calcium carbonate have been widely used in alkaline papermaking. Unfortunately, although increasing filler level in papers can improve the paper properties such as brightness, opacity, stiffness gloss, smoothness, porosity, and printability, as well as decrease cost, some strength of the paper is negatively affected. In this research, needle-like aragonite was synthesized using $Ca(OH)_2$ and $CO_2$ as reactants in the presence of $MgCl_2$ and characterized with scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The physical and optical properties of the paper handsheets containing these needle-like aragonite fillers were evaluated. Results indicated that tensile strength, Z-direction tensile strength and folding endurance of the paper were improved by the needle-like aragonite crystals compared to the paper using commercial PCC (precipitated calcium carbonate) as filler. The stiffness of the paper handsheet on the machine direction was increased, but no evident difference in the cross direction was found. The improvement of paper strength mainly resulted from the twining effect between the aragonite whiskers and paper fibers. The optical properties of the paper were slightly decreased with the use of the needle-like aragonites compared to commercial PCC. These results suggest that paper cost can be decreased by increasing the content of needle-like aragonite filler while paper strength will not be decreased compared to PCC filler.