• Applied Microscopy
• /
• 제32권1호
• /
• pp.31-37
• /
• 2002

[ $Mg_{68}Zn_{28}Y_4$ ] 합금의 응고 조직은 primary solidification phase, primary solidification phase로부터 성장된 ${\alpha}-Mg$ dendrite, 그리고 응고 말기에 형성된 eutectic structure의 세 가지형태 조직으로 구성되어져 있다. Primary solidification phase에는 매우 큰 정도의 phason strain이 존재하고 있으며, $a=27.2{\AA}\;and\;{\alpha}=63.43^{\circ}$의 격자상수를 갖는 1/1 rhombohedral approximant가 존재한다. 이와 같은 rhombohedral approximant의 구조는 six dimensional face centered hyper-cubic lattice에 phason strain을 도입함에 의해 얻어질 수 있다. Decagonal phase는 icosahedral phase로부터 방위 관계를 가지며 형성되며, $Mg_4Zn_7$는 decagonal phase로부터 방위관계를 가지며 성장한다. 이는 세 상간에 구조적 유사성이 존재하고 있음을 의미하며, 응고시 용질원자의 분배에 의해 이들 세 상이 순서대로 형성되어진다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.20-24
• /
• 2015

We studied the relationship between the surface smoothness of the internal Cu ribbon and the morphology of the Sn-Pb plating layer for solar cell modules. A bumpy surface was observed on the surface of the solar ribbon, which caused irregular reflection of light. Large, Pb-rich, primary ${\alpha}$-phases were found below the convex surface of the solar ribbon, passing from the surface of the internal Cu ribbon to the surface of the plating layer. The primary ${\alpha}$-phases heterogeneously nucleated on the convex surface of the Cu ribbon, and then largely grew to the convex surface of the plating layer. The restriction of the primary ${\alpha}$-phase's formation was enabled by enhancing the smoothness of the Cu ribbon's surface; it was also possible to increase the adhesive strength and decrease contact resistance. We confirmed that the solar ribbon's surface smoothness depends on the internal Cu ribbon's surface smoothness.

• 한국재료학회지
• /
• 제30권2호
• /
• pp.51-56
• /
• 2020

In this study, three kinds of metal chills such as SS400, AC4CH and brass, with different thicknesses of 40 ~ 80 mm, were applied for low pressure casting of Al-Si alloy to control cooling rate. The microstructural characteristics with increasing cooling rate were represented using factors including D₁, D₂, size of primary α phases and shape factor and size of eutectic Si. The tensile properties were investigated and additionally analyzed based on the microstructural characteristics. As the cooling rate increased, D₁, D₂, and sizes of primary α phases and eutectic Si apparently decreased and the shape factor of eutectic Si increased to over 0.8. The ultimate tensile strength (UTS) and yield strength (YS) increased with decreasing D₁, D₂, and size of primary α phases, while elongation increased with decreasing size of eutectic Si and concurrently increasing shape factor of eutectic Si. This indicated that the primary α phases and eutectic Si in Al-Si alloy were refined with increasing cooling rate, resulting in improvement of UTS and YS without sacrificing elongation. After the tensile test, preferential deformation of primary α phases was observed in the Al-Si alloy produced at higher cooling rates of more than 0.1 K/s.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 고액공존금속의 성형기술 심포지엄
• /
• pp.148-159
• /
• 1997

In this study, microstructure, size of primary $\alpha$, solid fraction and hardness of A356 Al alloy, were investigated. Semi-solid A356 allos were obtained by semi-solid continuous casting apparatus consists of melting furnace, formation apparatus of granular primary $\alpha$ and continuous casting apparatus. Size of promary $\alpha$ and fraction solid were decreased with decreasing temperature, and with increasing volume of cooling water. At the cooling water temperature of 15$^{\circ}C$ and cooling water volume of 18.2$\ell$/min, the sizes of primary $\alpha$ phases were decreased up to 40${\mu}{\textrm}{m}$, and fraction solid was 0.68.

• 한국주조공학회지
• /
• 제29권5호
• /
• pp.225-232
• /
• 2009

For comprehensive understanding of the formation behavior of $\beta-Al_5FeSi$ phase in Al-Si-Cu alloys with the existence of Fe element, microstructure characterizations were performed using combined analysis of OM, SEM-EDS, XRD. Especially, experimental and predictive works on solidification events of $\beta-Al_5FeSi$ phase as well as other phases formed together with $\beta-Al_5FeSi$ have been carried out by using DSC analysis and Java-based Materials Properties software (J. Mat. Pro.). Primary and eutectic $\beta-Al_5FeSi$ phases were able to distinguish from each other on microstructures by their morphological features. Primary $\beta-Al_5FeSi$ phase was seen to have rough surface perpendicular to growth direction, indicating free attachment of solute atoms in liquid state. On the other hand, the eutectic $\beta-Al_5FeSi$ phase was formed with plain and straight surface during eutectic reaction together with $\alpha$-Al phase. The eutectic reaction of $\beta-Al_5FeSi$ and $\alpha$-Al phases was seen to be able to separate into each formation depending on cooling rate.

• KSBB Journal
• /
• 제27권4호
• /
• pp.232-236
• /
• 2012

Comparative liquid chromatographic enantiomer separation of ${\alpha}$-amino acids, their esters and primary amino compounds was performed using two chiral stationary phases (CSPs) prepared by covalently bonding (+)-(18-crown-6)-2,3,11,12-tetracarboxylic acid (18-C-6-TA) of the same chiral selector. In general, the separation factors and resolution factors for these analytes on CSP 1 were greater than on CSP 2, while these capacity factors on CSP 2 were quite greater than on CSP 1. Except for leucine methyl ester and phenylalanine methyl ester, the elution orders of all analytes including ${\alpha}$-amino ${\alpha}$-alkyl acids and phenylglycine alkyl esters on CSP 1 are identical to those on CSP 2. This study showed that different connecting structures for these two CSPs might influence their ability to resolve the analytes depending on their structures related to the chiral recognition mechanism.

• 한국주조공학회지
• /
• 제21권2호
• /
• pp.135-140
• /
• 2001

Microstructure of the bell made with Cu-Sn alloys was examined by optical and scanning electron microscope and that analyzed quantitatively with image analyzer. Also acoustic characteristics of the bells were measured in detail by using FFT type power spectrum analyzer. ${\alpha}-single$ phases of large grains only were observed in Cu-5%Sn alloy. However mixed structure of primary ${\alpha}-phase$ and eutectoid of ${\alpha}+{\delta}%_o$ was existed in the Cu-Sn alloys with more than 9%Sn. Also the area fraction of eutectoid phases gradually increased with an increased Sn content. From the result of acoustic test, it was found that frequency and tonal intensity decreased with the increased Sn content from 5%Sn to 11%Sn, and those were rather increased with further increase of that. The lowest frequency and tonal intensity were showed in Cu-11%Sn, and porosity decreased considerably frequency and tonal intensity of the bells.

• 한국주조공학회지
• /
• 제17권1호
• /
• pp.67-75
• /
• 1997

The semisolid processing of two Al-Si alloys, A356 and Al-25wt%Si, was studied with using the rotor composed of permanent magnets. The semisolid slurry was agitated by the electromagnetic force induced from the rotating permant magnets. The round shaped primary ${\alpha}$ phases were formed in A356 alloy as a result of agitation. In Al25wt%Si alloy, spherodization of primary Si particles was not observed with the rotation of the magnets. The primary Si particles were segregated to the outer surface area of sample, which became pronounced with increasing the rotating speed of magnets.

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.106-115
• /
• 1995

To know the bonding phenomena of Ti/Cu brazed joint, a characteristic of microstructures in bonding interlayer of vacuum brazed pure Ti to Cu has been studied in the temperature range from 1088 to 1133K for various bonding times using Ag-28wt%Cu filler metal. Also intermediate phases formed in bonded interlayer and behavior of layer growth have been investigated. The obtained results in this study are as follows: 1) Liquid insert metal width at the each brazing temperature was proportional to the square root of brazing time, and it was considered that the liquid insert metal width was controlled by the diffusion rate process of primary .alpha.-Cu formed at the Ti side. 2) Intermediate phases formed near the Ti interface were .betha.-Ti and intermetallic compounds TiCu, Ti$_{2}$Cu, Ti$_{3}$Cu, and TiCu. 3) .betha.-Ti formed in Ti base metal durig brazing transformed to lamellar structure, .alpha.-Ti + Ti$_{2}$Cu. The structure came from the eutectoil decomposition reaction in cooling. And the width of .betha.-Ti layer was proportional to the square root of brazing time, and it was considered that the growth of .betha.-Ti layer was controlled by interdiffusion rate process in .betha.-Ti. 4) The layer growth of TiCu, Ti$_{3}$Cu$_{4}$ and TiCu, phases formed near the Ti interface was linerface was linearly proportional to the brazing time, and it was considered that the layer growth of these phases was controlled by the chemical reaction rate at the interface.

• Nuclear Engineering and Technology
• /
• 제30권6호
• /
• pp.518-530
• /
• 1998

A natural analogue study has been performed for the Koongarra uranium ore deposit in Australia as an international agreement of the Analogue Studies in the Alligator Rivers Region (ASARR). Rocks obtained from the Koongarra deposit, Northern Territory of Australia, were examined in order to understand uranium migration processes of primary and secondary ore-body in both weathered and unweathered zones. Total alpha activities of rock samples were measured to compare the relative amount of uranium in the sample. Uranium distributions have been investigated by means of both the alpha-autoradiography and the fission track registration technique after irradiation in a flux of thermal neutrons (~10$\times$$10^{13}$nㆍ$cm^{-2}$ㆍs$^{-1}$) for 2 minutes. The mineral phases corresponding to the registered alpha-tracks and fission tracks were identified by petrological observation with optical microscope as well as X-ray diffraction and electron microprobe analysis (EPMA). Uranium was found mostly inside of the fracture of the quartzite and its mineral phase was identified as sklodowskite. The mineral phase associated with high uranium concentration was found as illeminite by petrological observation with optical microscope as well as EPMA.