• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.964-968
• /
• 2007

The measurement of floor impact sound have been standardized in KS 2810-1 and 2. The height of receiving microphones position is specified in the standard as 1.2m which is almost half height of apartment rooms as a listening position. In this study, receiving positions are investigated by measuring the distribution of sound pressure levels at 792 receiving microphone positions in the standard testing building. Standard impact sources, tapping machine and impact ball, are driven on the center position in the source room where is located at the above floor. It was found that the distribution of sound pressure levels in the receiving room indicates significant deviation at different frequencies there is more than 5dB drop at 63Hz but 2dB rise at 125Hz at a height of 1.2m when the impact ball is driven, in the other case of a generating tapping machine there is more than 2dB rise at 125Hz at a height of 1.2m due to room modes.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.550-556
• /
• 2008

The aim of this research is to analyze the influence of motive pressure, driving nozzle position and nozzle throat ratio on the performance of ejector. The experiment was conducted in the variation of motive pressure of 0.196, 0.294, 0.392 and 0.490MPa respectively. The position of driving nozzle was varied in difference locations according to mixing tube diameter(0.5d, 1d, 2d, 3d, 4.15d, 5d and 6d). The experimental results show when the nozzle outlet is located at 3d, the flow characteristics change abruptly. It is shown that the suction flow rate and pressure lift ratio of ejector is influenced by the driving nozzle position. At nozzle position location of the Id of mixing tube diameter the performance of ejector gives the best performance.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.5
• /
• pp.521-529
• /
• 2012

Since the energy demand for refrigeration and air-conditioning has greatly increased all over the world, thermally activated refrigeration cycle has attracted much attention. This study carries out a performance analysis of a vapor compression cycle (VCC) driven by organic Rankine cycle (ORC) utilizing low-temperature heat source in the form of sensible heat. The ORC is assumed to produce minimum net work which is required to drive the VCC without generating an excess electricity. Effects of important system parameters such as turbine inlet pressure, condensing temperature, and evaporating temperature on the system variables such as mass flow ratio, net work production, and coefficient of performance (COP) are thoroughly investigated. The effect of choice of working fluid on COP is also considered. Results show that net work production and COP increase with increasing turbine inlet pressure or decreasing condensing temperature. Out of the five kinds of organic fluids considered $C_4H_{10}$ gives a relatively high COP in the range of low turbine inlet pressure.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.271-271
• /
• 2017

상수관망 수리해석 기법은 절점의 사용량 및 누수량을 기지의 값으로 고려하여 총 수요량이 모두 공급될 수 있다고 가정하여 해석하는 수요기반해석(Demand Driven Analysis, DDA)과 사용량과 누수량은 절점 압력수두에 의해 달라질 수 있어, 공급가능량 및 누수량과 절점의 압력수두 모두를 미지수로 고려하여 해석하는 수압기반해석(Pressure Driven Analysis, PDA)으로 구분될 수 있다. 본 연구에서는 수압기반사용량 모의(Pressure Dependent Demand, PDD)와 수압기반누수량 모의(Pressure Dependent Leakage, PDL)기능이 모두 구현되고, 다양한 시나리오 분석이 가능한 소프트웨어(SW)인 K-NRisk를 개발하였다. K-NRisk는 2016년 7월에 공개된 상수관망 해석범용모형인 EPANET3 소스코드 기반으로 개량 개발되었으며, 기존 EPANET2와 비교하였을 경우 사용자 편의성 증대를 위한 입출력 기능 및 SW 활용도 제고를 위한 대표업무분석 기능이 신규 개발, 강화되었다. 개발된 SW를 관망정비 및 공급안정성 확보 목적을 위한 수리해석 시 적용하여 그 결과를 분석하였다. 적용결과 기존 수요기반해석이 가지고 있는 한계점을 보완하고, 실제업무 시 활용가능함을 확인하였다.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.858-864
• /
• 2018

Graphene oxide (GO) laminate is a new promising material for water purification system, which has extraordinary permeability only for water molecule. It consists of numerous nano-channels, in which water molecules could be nano-confined, resulting in slip of the molecules for very fast transportation speed. In this study, water penetration rate via different thickness of GO membrane according to driven pressures are measured experimentally, so that speed of water molecules and permeability are evaluated. Generally, water penetration rate via a membrane with macroscopic-sized channel increases linearly with pressure difference between up and bottom side of the membrane, but that via GO membrane approaches asymptotic value (i.e. saturation) as like a log function. Moreover, the permeability of GO membrane was observed in inverse proportion to its thickness. Based on the experimental observations, a correlation for volume flux via GO membrane was suggested with respect to its thickness and external pressure difference.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.9 no.1
• /
• pp.15-19
• /
• 2013

The auxiliary feedwater is an important to remove the heat from the reactor core when the main feedwater system is unavailable. In most initiating events in Probabilistic Safety Assessment(PSA), the operaton of this system is required to mitigate the accidents. For one of domestic nuclear power plants, a design change of a turbine-driven auxiliary feedwater pump(TD-AFWP), pipe, and valves in the auxiliary system is implemented due to the aging related deterioration by long time operation. This change includes the replacement of the TD-AFWP, the relocation of some valves for improving the system availability, a new cross-tie line, and the installation of manual valves for maintenance. The design modification affects the PSA because the system is critical to mitigate the accidents. In this paper, the safety effect of the change of the auxiliary feedwater system is assessed with regard to the PSA view point. The results demonstrate that this change can supply the auxiliary feedwater from the TD-AFWP in the accident with the motor-driven auxiliary feedwater pump(MD-AFWP) unavailable due to test or maintenance. In addition, the change of MOV's normal position from "close" to "open" can deliver the water to steam generator in the loss of offsite power(LOOP) event. Therefore, it is confirmed that the design change of the auxiliary feedwater system reduces the total core damage frequency(CDF).

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.6
• /
• pp.135-141
• /
• 2009

Fracturing technique using fluid injection into the borehole is widely used technology in the industry for the geothermal heat, oil, and gas extraction. Dealing with fluid-driven natural fractures such as dike and vein indirectly, design technology would be improved by adapting their principles. In this paper, mechanical interaction between the segments is evaluated by modeling highly segmented and closely spaced fluid-driven natural fractures. The number of segments is 71 with 3,339 measured apertures in which the interaction is considerably predicted. To evaluate mechanical interaction, boundary collocation method is used and the net pressure is calculated by using least square method to fit measured apertures. As a result, in case that mechanical interaction is considered, two pressures as fitting parameters are sufficient to capture measured apertures.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.1-8
• /
• 2007

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke marine diesel engine is of great economic importance. In Korea, authors first developed a motor-driven cylinder lubricator for a Wartsila Switzerland large two-stroke diesel engine. The characteristic of the developed product is that can control automatically the oil feed rate with a load fluctuation by the motor drive and the offset cam. For manufacturing the reliable and useful products, however, it is necessary to investigate further characteristics and to improve performances as a cylinder lubricator. In this study, the effects of pump motor speed, plunger stroke and cylinder back pressure on oil feed rate, maximum discharge and delivery pressures are experimentally investigated by using the electronically controlled quill injection system and distributer in the developed cylinder lubricator. It is found that the oil feed rates of electronic control and mechanical type quills with the in-cylinder back pressure are differently characterized by the role of accumulator, the viscous resistance of contact area, etc. It can be also shown that the maximum discharge pressure of the electronic control quill is lower than the mechanical type one but the maximum discharge pressure difference of two types decreased as plunger stroke is small, and the maximum delivery pressures of two types increased as plunger stroke, motor speed and back pressure are elevated but the maximum delivery pressure of mechanical type is higher than the one of electronic control type.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.19-28
• /
• 2005

It is of great economic importance to minimize the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine. The motor-driven cylinder lubricator was first developed fur a large two-stroke marine diesel engine made in $W{\ddot{a}}rtsil{\ddot{a}}a$ Switzerland Ltd. by the joint research of industry-university. In this study, the effects of revolution speed, plunger stroke and cylinder back pressure on maximum discharge and delivery pressures, delivery delay duration, and oil feed rate are experimentally investigated by the home-manufactured cylinder lubricator. The maximum discharge pressure with a spot of 0.03 m and the maximum loss pressure at spots of 5, 6.78 and i 0 m away from the end of lubricator slot are increased as plunger stroke, revolution speed and back pressure are elevated, and the delivery delay duration is shortened as plunger stroke, revolution speed and oil pipe length are increased. Also, oil feed rate is increased as plunger stroke and revolution speed are raised, but lowered as the back pressure is increased.

• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.1-6
• /
• 2013

Traction control suppresses the spinning of the driven wheel during drive away or acceleration on slippery road condition. In this study, the estimation method of brake pressure hardly measured is proposed. The estimation method of brake pressure and the brake pressure control with pulse width modulation(PWM) are verified a good performance through experiment. Also, the vehicle simulation on slippery road conditions is validated the applicability of brake pressure control for traction control. The simulation results have showed that the brake pressure can be used the control variable for traction control.