• 펄프종이기술
• /
• 제31권3호
• /
• pp.19-25
• /
• 1999

Effects of the process variable in Condebelt press drying including drying temperature, pressure , drying time, and moisture content of the sheets on the paper properties were examined. The experiment was performed with a static rig and Korean OCC was used as raw material. Significant improvement in sheet density, compression strength, tensile strength, surface smoothness ,etc. was obtained when condebelt drying was applied. Control of pressure and inlet dryness was found to be two most critical variables in improving sheet properties.

• Tribology and Lubricants
• /
• 제20권1호
• /
• pp.27-32
• /
• 2004

This paper presents unsteady oil flow behaviors in the engine lubrication network to clarify the differences between continuous and discontinuous oil supply crankshaft system. Using commercial network analysis program, Flowmaster2, engine lubrication network system analysis were carried out. And effects of crankshaft speed and supplied oil pressure on pressure fluctuation in oil groove and oil flow rate to each bearing were analyzed.

• EDISON SW 활용 경진대회 논문집
• /
• 제3회(2014년)
• /
• pp.574-578
• /
• 2014

본 연구에서는 인접 구조물의 상호 간섭에 의한 풍압 변화에 대한 분석을 수행하였다. 두 개의 구조물 사이의 거리 및 위치를 변경하여 비교 해석하는 것으로써 사각형 구조물 구현을 위해 EDISON_CFD를 이용하여 수치해석을 하였고, 유한 체적 법(Finite Volume Method, FVM) 기반의 범용 비압축성 유동 해석을 위해 2D_Incomp-P_2.1 해석자를 사용하였다. 이 연구를 통하여 인접한 구조물의 영향을 분석하여 상호 간 거리와 위치를 결정할 수 있는 근거자료를 확보하였다.

• 설비공학논문집
• /
• 제8권1호
• /
• pp.110-119
• /
• 1996

A numerical of thermoacoustic refrigerators has been developed. Effects of heat transfer and viscosity on pressure and velocity distributions in resonators and heat exchangers were considered. Predictions of cooling capacity and COP agreed well with previous experimental results. Effects of important design parameters, such as pressure ratio, spacing between the plates in the stack and stack length, on the performance of thermoacoustic refrigerators were shown.

• 약학회지
• /
• 제37권6호
• /
• pp.631-637
• /
• 1993

In the previous report, it was described that the butanol fraction of the root bark extract of Aralia elata had potent antigastritic and antiulcerative effects in rats, In this pharmacological profile, the fraction revealed low acute toxicities in mice and rats, no central nervous system activities, moderate analgesic action, weak inhibitory action in carrageenin edema of rats and no direct effects on isolated smooth muscles of rats and guinea-pigs. Slight lowering of blood pressure as given i.v. in rabbit was observed.

• 대한치과의사협회지
• /
• 제53권4호
• /
• pp.259-265
• /
• 2015

Recently, oral appliances for treating snoring and obstructive sleep apnea are widely used. Among various appliances, mandibular advancement devices are most effective without serious side effects. Advancement of mandible keep airway open and decrease snoring and/or obstructive apnea events. They can be used as stand-alone therapy or an adjunct to continuous positive air pressure for lowering air pressure. Oral appliances should be applied by dentists who have knowledges and experiences on occlusion and temporomandibular disorders and manage of side effects.

• Archives of Pharmacal Research
• /
• 제15권1호
• /
• pp.104-108
• /
• 1992

2, 3-Diphenyl-6-formyl-5-methoxyindole reacts with ethyl cyano acetate to yield the arylidene derivative which forms with urea and thiourea the corresponding pyrimidine derivatives. The arylidene derivatives react with hydrazines and with active methylenes to form the respective pyrazole derivatives and the $\alpha, \;\beta$-disubstituted acrylonitriles. Seven new compounds were tested for their effects on the arterial blood pressure of rats and analgesic activity.

• Journal of Mechanical Science and Technology
• /
• 제20권9호
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

• 한국세라믹학회지
• /
• 제50권1호
• /
• pp.25-30
• /
• 2013

The pore volume of hardened cement with waterproofing materials is lower compared to that of hardened cement without waterproofing materials. Thus, fewer gaps will appear by means of chemical reactions between $Ca^{2+}$ ions in hardened cement and water, solutes, and other ions. Due to the selective permeability, the osmotic pressure of hardened cement can change due to physical effects such as the reduction of the pore volume and the reduction in the number of pores, as well as by the electrochemical reaction between water, solutes, other ions and $Ca^{2+}$ ions in hardened cement. Of course, these factors do not have independent effects but instead a combined complex effect. Accordingly, we studied changes in the osmotic pressure due to the difference in the pore structure of hardened cement. A pore size smaller than 1 nm in hardened cement had only a slight effect on the osmotic pressure, whereas a pore size larger than 1 nm had a direct effect on the osmotic pressure.

• 한국안전학회지
• /
• 제30권4호
• /
• pp.168-173
• /
• 2015

A steam generator tubing is one of the main pressure boundary of the reactor coolant system in the nuclear power plants. Structural integrity refers to maintaining adequate margins against failure of the tubing. Burst pressure of a tube at tube support plate can be higher than that for a free-span tube because failure behaviors could be interfered from the tube support plate. Alternative repair criteria for out-diameter stress corrosion cracking indications in tubes to the drilled type tube support plate were developed, however, there are very limited information to the eggcrate type tube support plate. This paper discussed reinforcement effect of steam generator tube burst pressure with axial out-diameter stress corrosion cracking within an eggcrate type tube support plate. A series of tube burst tests were performed under the room temperature and it was found out that there is no significant but marginal effects.