• Journal of Korean Clinical Nursing Research
• /
• v.29 no.3
• /
• pp.249-260
• /
• 2023

Purpose: The study aimed to examine the effects of nurse staffing levels on patient outcomes in long-term care hospitals in South Korea using path analysis. Methods: We conducted a secondary analysis of national data, which included the 2021 hospital assessment results of long-term care hospitals from the Health Insurance Review and Assessment Service. Data collection was performed between June 19 and June 27, 2023. The study sample consisted of 1,215 hospitals, and we analyzed the data using SAS 9.4 and Mplus 8 software. Results: The average numbers of patients per registered nurse, certified nursing assistant, and nursing staff, including both registered nurses and certified nursing assistant, was 10.00, 7.43, and 4.00, respectively. Path analysis revealed that the number of patients per registered nurse had direct effects on improvements in activities of daily living and indirect effects on indwelling catheterization, pressure ulcer improvement, and weight loss. The number of patients per certified nursing assistant had direct effects on new pressure ulcer development and pressure ulcer improvement, with no indirect effects. The number of patients per nursing staff had direct effects on pressure ulcer improvement and no indirect effects on other patient outcomes. Conclusion: The findings suggest that establishing policies to evaluate staffing levels of registered nurse and certified nursing assistants separately is necessary in order to improve registered nurse staffing levels and patient outcomes in long-term care hospitals.

• Journal of Korean Biological Nursing Science
• /
• v.13 no.1
• /
• pp.23-28
• /
• 2011

Purpose: The aim of this study were to examine the effects of abdominal breathing on preoperative anxiety and blood pressure. Methods: The research was a non-equivalent control group pretest-posttest design. The subjects were 60 patients that operated on under local anesthetic. Thirty subjects in the experimental group and 30 subjects in the control group. Data on anxiety and blood pressure for this study were collected from them. The collected data were analyzed by t-test, $X^2$-test, paird t-test. Results: After abdominal breathing, there was a statistically significant decline in the psychological anxiety level of the experimental group. With regard to the physical anxiety level, no statistically significant drop was detected in blood pressure. Conclusion: The findings of the study confirmed that abdominal breathing reduced preoperative anxiety of upper and lower limbs surgical patients.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.112-118
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis fur the filling and packing phases. Molding troubles like flow mark, weld line, sink mark, short shot and warpage can be caused by these injection molding process factors. Among them, the short shot was caused by that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition, as the flow rate for the volumetric shrinkage during the frozen phase could not be supplied properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing pressure.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.295-300
• /
• 1996

To investigate the effects of the side-orifice on the pressure drop for single-phase flow, a series of experiments have been carried out with 16 different downstream test sections with various combinations of side-orifice shapes, different numbers of side-orifices, and different arrangements of the side-orifice using water as a working fluid. From the measurements of the pressure drop and the flow rate, the pressure loss coefficient of the side-orifice(s) has been evaluated. Based on the total number of 529 present data, an empirical correlation for the pressure loss coefficient has been developed in terms of Reynolds number and geometric parameters, such as area ratio, equivalent diameter, leading edge, and average width of side-orifice.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.3
• /
• pp.227-234
• /
• 2010

Numerical analyses have been performed to investigate the effects of geometric parameters of a straight groove micromixer on mixing performance and pressure drop. Three-dimensional Navier-Stokes equations with two working fluids, water and ethanol have been used to calculate mixing index and pressure drop. A parametric study has been carried out to find the effects of the number of grooves per cycle, arrangement of patterned walls, and additional grooves in triangular dead zones between half cycles of grooves. The three arrangements of patterned walls in a micromixer, i.e., single wall patterned, both walls patterned symmetrically, and both walls patterned asymmetrically, have been tested. The results indicate that as the number of grooves per cycle increases the mixing index increases and the pressure drop decreases. The microchannel with both walls patterned asymmetrically shows the best mixing performance among the three different arrangements of patterned walls. Additional grooves confirm the better mixing performance and lower pressure drop.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.4
• /
• pp.44-53
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the filling and packing phases. Molding troubles like flow mark weld line, sink ma가 short shot and warpage car be caused by these injection molding process factors. Among them the short shot was caused by the fact that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition as the flow rate for the volumetric shrinkage during the f개zen phase could not be supplied Properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing Pressure.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2127-2132
• /
• 2003

A computational study is performed to better understand the choke phenomenon of unsteady gas flow through a critical nozzle. The axisymmetric, unsteady, compressible, Navier-Stokes equations are solved using a finite volume method. In order to simulate the effects of back pressure fluctuations on the critical nozzle flow, a forced sinusoidal pressure wave is assumed downstream the exit of the critical nozzle. It's frequency is 20kHz and amplitude is varied below 15% of time-mean back pressure. The results obtained show that for low Reynolds numbers, the unsteady effects of the pressure fluctuations can propagate upstream of the throat of critical nozzle, and thereby giving rise to applicable fluctuations of mass flow through the critical nozzle. The effect of the amplitude of the excited pressure fluctuations on the choke phenomenon is discussed in details.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.4
• /
• pp.15-20
• /
• 2013

Nanoimprint lithography (NIL) is the next generation photolithography process in which the photoresist is dispensed onto the substrate in its liquid form and then imprinted and cured into a desired pattern instead of using traditional optical system. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. In this paper, a pressure vessel type imprinting system was used to imprint patterns with two type pressure values (25 bar, 30 bar) and two type pressure keeping times (5 min, 10 min). The height of transferred pattern and the thickness of residual layer were measured and effects of pressurization conditions - pressure and pressure keeping time - on the pattern transfer in thermal NIL were investigated.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.82-87
• /
• 1996

To find the effects of pressure on critical heat flux (CHF) for the conditions of low pressures (especially up to 10 bar) and low mass flux (~300 kg/$m^2$s), a series of experiments have been accomplished by using uniformly heated Inconel-625 tube. The experimental ranges are as follows: pressure (from 1.2 to 8 bar). mass velocities (from 100 to 250 kg/$m^2$s) and the inlet subcooling ($\Delta$h$_{i}$ ＝ 350 kJ/kg). According to the experimental data, it is found that the CHF is nearly independent of the pressure and increases with mass flux. From the results of the CHF correlation assessment for this experimental data, we could find somewhat different tendency of CHF behavior from every other CHF prediction correlation and table.ation and table.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.33-42
• /
• 1994

An influence of inlet pressure on the performance of sector-shaped pad thrust bearings is investigated theoretically. The optimum conditions of film thickness or the optimum positions of pivot are found through the evaluation of load capacity for all available conditions of film thickness, under the operating conditions which the thermal and pad deformation effects can be neglected. The bearing performance including the inlet pressure effects is obtained for a wide operating ranges that inertia parameter(Re$^{*}$) is up to unity, and for the various cases of pad extent angle (number of pad) and the three cases of the angle between pads. The results show that the inlet pressure has a large influence on the performance of sector-shaped pad thrust bearings. In the design of sector-shaped pad bearings, due to the inlet pressure, the optimum number of pad is varied with the operating speed and the angle between pads, and the optimum position of pivot is located toward the leading edge along with the operating speed increases.