• 대한금속재료학회지
• /
• 제47권11호
• /
• pp.728-733
• /
• 2009

Cu based amorphous ($Cu_{54}Zr_{22}Ti_{18}Ni_{6}$) powders were deposited onto Al 6061 substrates by cold spray process with different powder preheating temperatures (below glass transition temperature: $350^{\circ}C$, near glass transition temperature: $430^{\circ}C$ and near crystallization temperature: $500^{\circ}C$). The microstructure and macroscopic properties (hardness, wear and corrosion) of Cu based amorphous coating layers were also investigated. X-ray diffraction results showed that cold sprayed Cu based amorphous coating layers of $300{\sim}350{\mu}m$ thickness could be well manufactured regardless of powder preheating temperature. Porosity measurements revealed that the coating layers of $430^{\circ}C$ and $500^{\circ}C$ preheating temperature conditions had lower porosity contents (0.88%, 0.93%) than that of the $350^{\circ}C$ preheating condition (4.87%). Hardness was measured as 374.8 Hv ($350^{\circ}C$), 436.3 Hv ($430^{\circ}C$) and 455.4 Hv ($500^{\circ}C$) for the Cu based amorphous coating layers, respectively. The results of the suga test for the wear resistance property also corresponded well to the hardness results. The critical anodic current density ($i_{c}$) according to powder preheating temperature conditions of $430^{\circ}C$, $500^{\circ}C$ was lower than that of the sample preheated at $350^{\circ}C$, respectively. The higher hardness, wear and corrosion resistances of the preheating conditions of near $T_{g}$ and $T_{x}$, compared to the properties of below $T_{g}$, could be well explained by the lower porosity of coating layer.

• 한국기계가공학회지
• /
• 제18권10호
• /
• pp.93-98
• /
• 2019

Recently, with the development of the aerospace and automotive industries, the demand for high-melting-point materials has increased. However, high-melting-point materials are difficult to cut through conventional machining methods. Thermally assisted machining (TAM) is a method for improving the machinability by preheating the materials. A laser, the most commonly used device for TAM, has high efficiency through local preheating but is not sufficient for maintaining a high preheating temperature due to rapid cooling. However, the use of multi-heat sources can supplement the disadvantage of a single heat source. The high preheating temperature can be maintained with a wide and deep heat-affected zone (HAZ) by multi-heat sources. The purpose of this study is to analyze the preheating effects of multi-heat sources using laser plasma. Thermal analysis and preheating experiments were carried out. As a result, the high preheating effect of multi-heat sources compared with a single heat source was verified.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제24회 KOSCO SYMPOSIUM 논문집
• /
• pp.79-84
• /
• 2002

The catalytic heat exchanger was designed which employs the regenerative preheating system of combustion air. The characteristics of the catalytic heat exchanger have been experimentally studied at the various operating parameters. The results showed that the mixture velocity did not affect significantly the performance of catalytic combustor whereas the preheating temperature of combustion air affected significantly the conversion rate. The complete conversion was achieved in the catalyzed honeycomb at a preheating temperature of $370-390^{\circ}C$, a mixture velocity of 0.53 $^{\sim}$ 0.75 m/s and an equivalence ratio of 0.19 $^{\sim}$ 0.27. The heat exchange efficiency of the catalytic heat exchanger appeared to be about 75 % when the air of room temperature was used as a working fluid. The results showed that both the heat balance of the system and the mixture conditions determine its stable catalytic combustion.

• 한국정밀공학회지
• /
• 제31권1호
• /
• pp.29-33
• /
• 2014

Recently, Difficult-to-cut materials are used in many manufacturing industry. But the difficult-to-cut materials are difficult-to-cutting process. So difficult to cut material cutting process was used after heat treatment through preheating for easy cutting process. In this study, Inconel 625 was preheating using laser heat source in computer simulation. Laser heat source temperature applied $1290^{\circ}C$ that suitable preheating temperature for Inconel 625. And temperature effects such as temperature distribution for moving heat source studied apply to similar actual process condition. Simulation results for heat treatment effects through temperature distribution verified.

• 한국분말재료학회지
• /
• 제9권2호
• /
• pp.96-102
• /
• 2002

In the present study, equiatomic porous TiNi shape-memory alloys have been successfully prepared by self-propagating high-temperature synthesis (SHS) using elemental titanium and nickel powders. The porous TiNi alloys thus obtained have an open porous structure with about 64 vol.% porosity, and the pore size is about 1.8 mm. The effect of preheating temperature on the microstructure have been investigated. It is found that the pore size increases with increasing preheating temperature. Moreover, the preheating temperature was shown to have a significant effect on the microstructrue of the SHS-synthesized porous TiNi shape memory alloys.

• 한국식생활문화학회지
• /
• 제14권5호
• /
• pp.455-460
• /
• 1999

In order to establish the processing condition of salt-fermented liquefaction of sardine (Sardinops melanoslicta), effect of temperature, pH value, and concentration of salinity on crude enzyme activity of sardine viscera were investigated. The optimum temperature range of crude enzyme activity in sardine viscera was $45{\sim}50^{\circ}C$ and the optimum pH value of it was 9.8. According to the concentration of salinity increased the crude enzyme activity in sardine viscera decreased. The relationship between concentration of salinity (X) and the crude enzyme activity (Y) in sardine viscera is shown as follows; Y=-0.01363X+0.7676 (r=-0.88). For the purpose of processing conditions of rapid- and low salt-fermented liquefaction of sardine, changes of viable cell count, histamine content, and volatile basic nitrogen (VBN) in the chopped whole sardine with 8% NaCl during preheating process at $40^{\circ},\;45^{\circ}$ and $50^{\circ}C$ for 48 hrs were analyzed. During preheating, initial viable cell counts of chopped whole sardine were $10^{4-7}/g$, but they decreased $10^{1-5}/g$ after 48 hrs. Histamine contents during preheating process at $40^{\circ}\;and\;45^{\circ}C$ were gradually increased, whereas at $50^{\circ}C$ were almost the same level after 48 hrs. VBN contents were continuously increased during preheating, but preheating at $50^{\circ}C$ samples were lower level than that of $40^{\circ}\;and\;45^{\circ}C$ ones. For the purpose to accelerate the fermentation and liquefaction of chopped whole sardine, preheating at optimum temperature of crude enzyme activity for 48 hrs was useful processing method and the contents of viable cell count, histamine, and VBN were safety level for food sanitation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.73-76
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in term of different processing variables such as preheating temperature, speed of mold rotation and cooling rate by centrifugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050^{\circ}C{\sim}1100^{\circ}C$ and $550^{\circ}C$ for 30min, respectively. The mould roating speed was 1000rpm. A tube was annealed at $840^{\circ}C$ for 72hours in oxygen atmosphere. The plate-like grains were well developed along the roating direction and typical grain size was about more than $40{\mu}m$. It was found that Ic values increased with increasing the preheating temperature and speed of mold rotation. While Ic decreased with increasing the cooling rate. The measured Ic in $50mm{\times}70mm{\times}2.5mm$ tube was about 896Amp.

• 대한기계학회논문집B
• /
• 제29권6호
• /
• pp.722-729
• /
• 2005

Design analysis of the solid oxide fuel cell and gas turbine combined power system is performed considering different methods for preheating cell inlet air. The purpose of air preheating is to keep the temperature difference between cell inlet and outlet within a practical design range thus to reduce thermal stress inside the cell. Three different methods considered are (1) adopting a burner in front of the cell, (2) adopting a preheater (heat transfer from the main combustor) in front of the cell and (3) using recirculation of the cathode exit gas. For each configuration, analyses are carried out for two values of allowable maximum cell temperature difference. Performance characteristics of all cases are compared and design limitations are discussed. Relaxation of the cell temperature difference (larger difference) is proved to ensure higher efficiency. Recirculation of the cathode exit gas exhibits better performance than other methods and this advantage becomes more prominent as the constraint of the cell temperature difference becomes more severe (smaller temperature difference).

• 한국전기전자재료학회논문지
• /
• 제18권5호
• /
• pp.468-472
• /
• 2005

High-temperature Superconductor(HTS) tubes were fabricated in term of different processing variables such as preheating temperature, speed of mold rotation and cooling rate by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050{\circ}C{\sim}1100{\circ}C\;and\;550{\circ}C\;for\;30\; min$, respectively The mould roating speed was 1000 rpm. A tube was annealed at $840 {\circ}C$ for 72 hours in oxygen atmosphere. The plate-like grains were well developed along the loafing direction and typical grain size was about more than $40{\mu}$. It was found that Ic values increased with increasing the Preheating temperature and speed of mold rotation. While Ic decreased with increasing the cooling rate. The measured Ic in $50mm{\times}70mm{\times}2.5mm$ tube was about 896 Amp.

• 열처리공학회지
• /
• 제11권1호
• /
• pp.62-72
• /
• 1998

High carbon steel is used for rails due to the excellent wear resistance, however the welding of high carbon steel is more difficult than that of mild steel owing to the high hardenability and sensitivity to cracking at the weldment. In this study, the impact toughness and cracking behavior of a rail weldment were evaluated as function of preheating temperatures. Impact toughness were more excellent in the specimen welded with preheating temperature above $250^{\circ}C$ than that below $100^{\circ}C$, and cracks were not detected in the specimen welded with preheating temperature above $250^{\circ}C$.