• 한국세라믹학회지
• /
• 제31권1호
• /
• pp.97-103
• /
• 1994

The influence of ground petroleum coke, preheat-treated at temperatures ranged of 150~35$0^{\circ}C$, was studied. It has been found that the coke powder preheat-treated at the temperature of 175$^{\circ}C$ has been spherical-shaped in grinding and have showed the highest strength and density in sintering. The coke powder was also the best for the binding force and the (H/C) values showed 0.45 at the above temperature.

• 한국세라믹학회지
• /
• 제30권7호
• /
• pp.557-562
• /
• 1993

Following conclusions are made from the detalied research on the relation between the phase change of the petroleum raw cokes after ball milling and the preheat treatment temperature. The petroleum raw cokes species are preheated in the temperature range of 350~45$0^{\circ}C$. At the preheat treatment temperature of 40$0^{\circ}C$ the particles of petroleum raw cokes from ball milling become spheically shape with the almost uniform particle size distribution of 1~5${\mu}{\textrm}{m}$. At the same temperature, they became low-graphitized with the d0.02 X-ray diffraction index of 3.41$\AA$. The carbon material made from the petroleum raw cokes at 40$0^{\circ}C$ turned out to have the good modulus of rupture about 600kg/$\textrm{cm}^2$, with the bulk density around 1.8g/㎤ and the appearent porosity around 8%.

• 한국축산식품학회지
• /
• 제36권5호
• /
• pp.671-678
• /
• 2016

Fractioning and/or preheating treatment on the rheological properties of myofibrillar protein (MP) gels induced by microbial transglutaminase (MTG) has been reported that they may improve the functional properties. However, the optimum condition was varied depending on the experimental factors. This study was to evaluate the effect of red bean protein isolate (RBPI) on the rheological properties of MP gels mediated by MTG as affected by modifications (fractioning: 7S-globulin of RBPI and/or preheat treatment (pre-heating; 95℃/30 min): pre-heating RBPI or pre-heating/7S-globulin). Cooking yields (CY, %) of MP gels was increased with RBPI (p<0.05), while 7S-globulin decreased the effect of RBPI (p<0.05); however, preheating treatments did not affect the CY (p>0.05). Gel strength of MP was decreased when RBPI or 7S-globulin added, while preheat treatments compensated for the negative effects of those in MP. This effect was entirely reversed by MTG treatment. Although the major band of RBPI disappeared, the preheated 7S globulin band was remained. In scanning electron microscopic (SEM) technique, the appearance of more cross-linked structures were observed when RBPI was prepared with preheating at 95℃ to improve the protein-protein interaction during gel setting of MP mixtures. Thus, the effects of RBPI and 7S-globulin as a substrate, and water and meat binder for MTG-mediated MP gels were confirmed to improve the rheological properties. However, preheat treatment of RBPI should be optimized.

• 대한치과기공학회지
• /
• 제24권1호
• /
• pp.33-41
• /
• 2002

In dental prosthetics, the application of metal-ceramic restorations has steadily increased since their introduction. This is due to excellent esthetics in combination with high mechanical stability. In order to optimum bond strength between metal and ceramics, controlled oxidation of metal substructure is essential factor. Beryllium containing and beryllium free Ni-Cr alloys for metal-ceramic restorations were evaluated for the metal-ceramic bond strength by changing heat treatment for oxide formation. A mechanical three-point bending test was employed to evaluate the interfacial bond strength of metal-ceramic. In each metal, plate type specimens were used for mechanical three-point bending test. With Ni-Cr alloys for metal ceramics, mechanical three-point bending test showed that double degassing was more available preheat treatment method than another. It was found that beryllium containing Ni-Cr alloys are more effective than beryllium-free for metal-ceramic bond strength.

• 열처리공학회지
• /
• 제13권4호
• /
• pp.246-252
• /
• 2000

Stellite 12 alloy-powder was overlaid on 410 stainless steel valve seat using plasma transferred arc(PTA) process. Variation of characteristic of microstructure and hardness of deposit with current(90~150 A) and preheat temperature(R.T.~$400^{\circ}C$) was investigated. Important conclusion obtained are as follows; All welding conditions used produced a sound deposit layer with no defect in single pass welding. The maximum deposit had 4.0~4.8 mm in thickness and its bead width was increased with increase of current and preheat temperature. The deposit showed hypoeutectic microstruture, which was consisting of primary cobalt dendrite and networked $M_7C_3$ type eutectic carbides. The amount of eutectic carbides was decreased and its dendritic secondary arm spacing was increased with increase of current. Hardness of the deposit was decreased with increase of current. Preheat temperature up to $400^{\circ}C$, however, showed little influence on the hardness and microstructure. The hardness was also influenced by diluted Fe content near the interface in addition to microstructure and dendritic secondary arm spacing. Hot hardness at $500^{\circ}C$ showed higher than 300 HV.

• 분석과학
• /
• 제22권1호
• /
• pp.51-56
• /
• 2009

천리포 해안사구 퇴적층에 대한 연대측정을 Optically Stimulated Luminescence (OSL)을 이용하여 Single Aliquot Regeneration (SAR) 법 중 열처리 조건을 일부 수정하여 실시하였다. 예열과 cut-heat을 각각 $260^{\circ}C$ 10 초 $-220^{\circ}C$ 0 초와 $270^{\circ}C$ 10 초 $-270^{\circ}C$ 10 초의 두 가지 조합을 적용하였다. 예열 및 cutheat의 열처리 과정을 변화시킴으로써 원하는 신호만을 선별하는 것이 가능했으며, 이를 등가선량을 구하는데 이용하였다. 또한 시료를 $75{\mu}m$, $150{\mu}m$, $200{\mu}m$의 표준체로 크기를 4개의 영역으로 구분하였고, 열처리 조건의 변화와 입자의 크기가 달라짐에 따라 등가선량이 다르게 측정되어 다른 연대가 산출되었다. 그 결과는 방사성탄소연대측정법에 의한 연대와 비교하였다. 입자의 크기에 따라 다른 연대가 산출된 것으로 미루어 천리포 해안사구 퇴적지층은 토양의 유입원이 혼합되어 구성되었음을 추정할 수 있었다.

• 소성∙가공
• /
• 제9권1호
• /
• pp.66-71
• /
• 2000

The present study tackles the metallurgical subjects involving the thin slab-direct hot rolling process, i.e. mini-mill process. In order to clarify the effect of chemical composition of steel and MnS precipitation behaviors on the development of edge cracking during hot rolling, the content of manganese and sulfur in low carbon steel was varied and the isothermal treatment prior to roughing was applied. Edge cracking during roughing in the hot-rolling process of mini-mill was effectively prevented by means of the isothermal treatment at 115$0^{\circ}C$ for 5 minutes in the 0.4% manganese steel containing sulfur lower than 0.013%. With the increase in manganese content in low carbon steel, coarser MnS developed. The edge cracking index which denotes the total length of edge crack per unit edge-length of rolled specimens was proposed in this paper. It was found that the edge cracking index linearly decreased with the increase in the ratio of MnS.

• 한국염색가공학회지
• /
• 제7권3호
• /
• pp.11-14
• /
• 1995

열처리 온도를 각각 다르게 한 Poly(ethylene terephthalate)에 반응기 내의 처리 조건이 서로 다른 두 가지 플라즈마 장치를 사용하여 산소 저온 플라즈마 처리를 했다. 열처리 온도가 플라즈마 감량에 미치는 영향은 열처리 온도가 증가함에 따라 결정화도도 증가하지만 감량율은, 열처리 온도가 16$0^{\circ}C$까지는 감소하다가 16$0^{\circ}C$ 이상에서는 증가하는 경향을 보이며, 분산염료에 의한 Poly(ethylene terephthlate) 섬유의 염색특성과 유사한 거동을 나타냈다.

• 한국식품과학회지
• /
• 제22권6호
• /
• pp.659-667
• /
• 1990

옥수수전분을 무수초산과 아세틸화반응을 시켜 슬러리상태의 재래적인 방법과 예열처리에 의한 방법 및 extrusion 공정에 의하여 초산전분을 제조하여 이화학적 성질을 비교하였다. 재래적인 방법으로의 초산전분을 제조(CSA)할 경우 최고의 치환도를 갖는 반응 최적조건은 반응온도 $35^{\circ}C$와 반응 pH8.5이었다. Anhydrous glucose unit에 대하여 무수초산의 mole비를 0.03에서 0.2로 증가시킬 경우 최적조건에서의 치환도는 0.019에서 0.082로 증가한 반면 아세틸화반응 수율은 31.6%에서 20.5%로 감소되었다. 예열처리를 $65^{\circ}C$와 $90^{\circ}C$에서 처리하여 초산전분제조(PSA)시 치환도는 각각 0.027과 0.040 이었다. Extrusion 공정에 의한 초산전분제조(WESA)시 치환도는 0.02이었다. 초산전분의 호화개시온도와 호화 enthalpy는 치환도가 증가함에 따라 원료전분보다 낮아졌다. 모든 초산전분시료가 원료전분에 비하여 투명도가 증가되었고 색도에 있어서 명도는 감소되었고 황색도는 증가되었다. WESA 시료는 원료전분, CSA 및 PSA 시료에 비해 낮은 곁보기점도를 보였으며 뉴우톤성 유체에 접근하였다. 고유점도는 CSA와 WESA 시료가 원료전분보다 낮았으나 PSA 시료는 약간 큰 값을 보였다. 초산전분겔의 노화시간상수는 모든 초산전분시료가 원료전분보다 큰 상수값을 보였다.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.99-110
• /
• 1998

The effects of pre-heat treatment(Q/T) on microstructure and hardness of SCM435 structural steel nitrided by micro-pulse plasma was investigated. The quenching and tempering temperatures for obtaining matrix hardness of SCM435 steel on range of HRC30 to HRC40 desired for machine parts were about $860^{\circ}C$ and $500^{\circ}C$ respectively. The case depth of SCM435 nitrided at $480^{\circ}C$ for 5 hours was independent of pre-heat treatment condition and was approximately $150{\mu}m$. However, hardness and compactness of nitrified layer on Q/T treated specimen were more heigher than annealed specimen. The case depth increased linearly with the increase of nitriding temperature, however, the hardness of nitrified layer decreased with the temperature. Phase mixture of ${\gamma}^{\prime}$-phase($Fe_4N$) and ${\varepsilon}$-phase($Fe_3N$) were detected by XRD analysis in the nitrified layer formed at optimum nitriding condition, and only single ${\gamma}^{\prime}$-phase was detected in the nitrified layer formed at higher nitriding temperature such as $540^{\circ}C$. The optimum nitriding temperature was approximately $480^{\circ}C$ which is lower than tempering temperature for preventing softening behavior of SCM435 matrix during nitriding process and the surface hardness of nitrified layer obtained by optimum preheat treatment condition was about Hv930.