• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.79-87
• /
• 1996

SMC(Sheet Molding Compound) is made of unsaturated polyester resin and other additives reinforced with randomly distributed chopped fiberglass strands. Because of its higher stiffness per unit mass, SMC was used as a substitute for steel for automotive steel outer panels. Thus, understanding of flow characteristics during fabrication of SMC is of importance since the formation of weld line depends on material flow. In the present study, SMC compression molding simulations in the flat and T-shape molds were accomplished. During simulations, the preferential the preferential flow occurred at the low mold closing speed while plug flow was observed for the higher mold closing speed. When the preferential flow was observed, the weld line was seen at the final stage. For simulations, rigid-viscoplastic finite element method was applied. Self-contact algorithm was also applied in order to predict the formation of the weld line. Simulation results were compared to the experimental results available in the literature.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.2
• /
• pp.62-73
• /
• 1997

The application of nutrients and pesticides to agricultural lands has been reported to contribute to groundwater contamination, which can be explained by preferential flow in lieu of convective-dispersive flow. An one-dimensional numerical model depicting preferential water and solute movement was modified to describe multi-layer flows. The model is based on a piecewise linear conductivity function. By combining conservation of mass and Darcy's law and using the method of characteristics a solution is obtained for water flow in which water moves at distinct velocities in different flow regions instead of an average velocity for the whole profile. The model allows transfer ofqr solutes between pore groups. The transfer is characterized by assuming mixing coefficients. The model was applied to undisturbed soil columns and an experiment site with structured sandy clay loam soil. Chloride, bromide, and 2, 4-D were used as tracers. Simulated solutes concentrations were in good agreement with the soil column data and field data in which preferential flow of solute is significant. The proposed model is capable of describing preferential solute transport under laboratory and field conditions.

• Economic and Environmental Geology
• /
• v.37 no.4
• /
• pp.383-389
• /
• 2004

Understanding flow pattern of water and solute in subsurface is essential for the reduction and prevention of contamination of soil and groundwater and for the investigation and remediation of contaminated site. The objective of this study is to examine the infiltration pattern in a soil developed from the Jurassic granite using (Brilliant Blue FCF $C_{37}H_{34}N_{2}Na_{2}O_{9}S_{3}$), the nonfluorescent and nontoxic food dye. All image processing was conducted using geographic image processing software, ER Mapper, Version 6.2. The dye coverage was determined by counting the stained pixels in the photographs (80${\times}$80cm, 80TEX>${\times}$5cm) for the vertical and horizontal view. A homogeneous matrix flow occurred in the A horizon with weak, medium granular structure and fingering at the interface of finer-textured A horizon and coarser-textured C horizon. Pegmatitic vein originated from the granite and plant root in C horizon induced preferential flow.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.655-662
• /
• 1985

화염스트레치와 확산선호도가 예혼합화염에 미치는 영향을 몇가지 모델에 대해 현상적으로 고 찰하였다. 즉, 정상상태의 구형화염, 구형으로 전파되는 화염, 균일유동장내의 곡면화염, 일차원 평면화염, 그리고 확대유동장내에서 스트레치된 평면화염등을 고찰하였으며, 이 해석의 결과는 화염면의 면적 변화율로 정의된 화염스트레치의 제인자들 즉, 비균일 접선속도장과 전파화염의 곡률에 의한 영향들이 공통적 특성을 나타냄을 보여주고 있다. 화염스트레치와 확산선호도가 화염전파속도에 미치는 복합효과는 세가지로 나타나는데 이는 화염온도의 변화에 따른 화학반 응강도의 변동, 열 및 물질확산의 강도차이, 그리고 대류 및 확산전달의 방향의 상이함에 기인 한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.2
• /
• pp.232-240
• /
• 1986

Extinction characteristics of the two interacting premixed flames are analyzed for the effects of flame stretch and preferential diffusion using large activation energy asymptotic analysis by adopting counterflow system as a model problem. Results show that the flammable limit of the thermally interacting premixed flames is extended compared to the single flame, and the extinction mechanism is classified into weak and strong interactions. As the lewis number of the deficient species increases, the region of strong interaction diminishes which can explain the different characteristics of the extinction boundaries of the lean (rich) methane/air and butane/air flames. The influence of the flame stretch to the interaction boundaries is also studied.

• Proceedings of the KOSOMBE Conference
• /
• v.1994 no.05
• /
• pp.115-118
• /
• 1994

Three-dimensional steady and pulsatile flows in an end-to-side anastomosis were investigated using a finite difference method in order to understand the flow dynamics in the preferential development of distal anastomotic intimal hyperplasia or thrombosis. Steady flow results revealed that a double helical vortex was formed in the host artery and flow recirculations near tow and heel regions were limited due to the secondary flow. Oscillating wall shear stress with significant secondary flow might be the flow dynamic reason of developing intimal hyperplasia or thrombosis.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.2
• /
• pp.71-78
• /
• 2000

Preferential flow has recently been the subject of increasing interest because these phenomena contribute to solute transport in soils. Commonly, preferential flow paths are associated with macropores or highly structured soils. We presented an analysis of the measured breakthrough curves (BTCs) of $Cl^-$ and $Cu^{2+}$ ions to test the occurrence of preferential flow in soils using miscible displacement technique under steady flow conditions. We also analyzed soil water retention curves and from this curves induced cumulative pore size distribution of undisturbed soils, which sampled from Ap1, B1, and C horizons of Songjeong series soils (the fine loamy, mesic family of Typic Hapludults). In this study, miscible displacement experiment on C horizon was excluded, because it is structureless sandy loam with saturated hydraulic conductivity of $5.2cmhr^{-1}$. The saturated hydraulic conductivity of Ap1 horizon was $2.0cmhr^{-1}$, which was about 7 times higher than that of B1 horizon ($0.27cm hr^{-1}$). Cumulative pore size distribution predicted that Ap1 horizon had more macropores (pore diameter larger than $49{\mu}m$, equivalent to -6 kpa of soil matric potential) than B1 horizon. The hydrodynamic dispersion coefficient from chloride BTCs was estimated as $1.3cm^2hr^{-1}$ for B1 and $34cm^2hr^{-1}$ for Ap1 horizon. However the retardation factors of B1 and Ap1 horizon were significantly different, i.e. 1 and 0.6, respectively, which means that there was distinct partition between mobile water and immobile phase in Ap1 horizon. The copper retardation effect of Ap1 horizon was less than that of B1 horizon, even though cation exchange capacity of Ap1 horizon was higher than that of B1 horizon. Thus, breakthrough curves of $Cl^-$ and $Cu^{2+}$ obviously showed the probability that preferential flow would occur in Ap1 horizon.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.2
• /
• pp.488-499
• /
• 1996

SMC(Sheet molding compound) is a thermosetting material reinforced with chopped fiberglass. The compression molding of SMC was analyzed based on a rigid thermo-viscoplastic approach using a three dimensional finite element program coupled with temperatures. Only the temperature analysis part was tested in this paper by solving one-dimensional heat transfer problem and comparing with the exact solutions available in the literature. Based on this comparison the program was proved to be valid and was further applied in solving compression molding of SMC between flat dies. To investigate the usefulness of a rigid thermo-viscoplastic approach in the compression molding analysis of SMC charge, compression of rectangular shaped SMC charge at plane strain and three dimensionalde formation condition was analyzed under the same condition as given in the literature. From this comparison it was found out that the rigid thermo-viscoplastic approach was useful in analyzing SMC compression molding between flat dies.

• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.39-47
• /
• 1995

The compression molding of SMC (sheet molding compund) at room temperature was analyzed based on rigid-viscoplastic approach by three dimensional finite element program. The developed program was tested by solving the three dimensional compression of wedge type specimens of aluminum alloys at various processing conditions. The simulation results were compared well to the experimental results available in the literature. based on this comparison the program was proved to be valid and was further applied in solving compression molding of SMC, which is a thermosetting material reinforced with chopped fiber glass. To investigate the effects of friction conditions and mold closing speeds for compression molding of SMC charge at room temperature, compressions of the cylindrical and rectangular shaped SMC were analyzed for various friction conditions and mold closing speeds. The calculated load values were compared to the experimental results for the compression molding of cylindrical specimen.

• The Journal of Engineering Geology
• /
• v.3 no.3
• /
• pp.241-252
• /
• 1993

Lead bas been found in the groundwater in Door County, Wiscorsin, with temporally and spatially irregular distribution in concentration. Correlation coeffidents were calculated among lead indicators in groundwater(frequency of lead detections, mean and maximum concentration of lead detections) and seven independent variables(stucture and geographic factors of wells, hydrogeological factors at lead-arsenate mixing sites and the level of soil contamination) which are possibly related to the lead level in groundwater. The significance of relationships was determined statistically by a t-test at the 90% confidence level, and indicated that the spatially located lead-arsenate mixing sites provided the lead in groundwater in the study area. A total of 112 groundwater samples were collected from 5 house wells with previous lead detects. Lead was detected in partides on ifiter papers with $0.45{\;}\mu\textrm{m}$ pore size, but not in filtrates. The result of chemical analysis for lead indicates that lead is associated with partides in groundwater in Door County. Subsequently, the irregular distribution of lead in the county results from the transport of particulate lead along the advective groundwater movement through the preferential pathways sucn as vertical and bedding-plane joints.