• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2016년도 학술발표회
• /
• pp.196-196
• /
• 2016

Landslide dam failure presents as a severe natural disaster due to its adverse impact to people and property. If the landslide dams failed, the discharge of a huge volume of both water and sediment could result in a catastrophic flood in the downstream area. In most of previous studies, breaching process used to be considered as a constructed dam, rather than as a landslide dam. Their erosion rate was assumed to relate to discharge by a sediment transport equation. However, during surface erosion of landslide dam, the sediment transportation regime is greatly dependent on the slope surface and the sediment concentration in the flow. This study aims to accurately simulate the outflow hydrograph caused by landslide dam by overtopping through a 2D surface flow erosion/deposition model. The lateral erosion velocity in this model was presented as a function of the shear stress on the side wall. The simulated results were then compared and it was coherent with the results obtained from the experiments.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1998년도 춘계학술발표회논문집(1)
• /
• pp.449-456
• /
• 1998

A theoretical critical heat flux (CLE) model. based on lateral bubble coalescence on the heated wall, is proposed to predict the subcooled flow boiling CHF in a uniformly heated vertical tube. The model is based on the concept that a single layer of bubbles contacted to the heated wall events a bulk liquid from reaching the wall at near CHF condition. Comparisons between the model predictions and experimental data result in satisfactory agreement within less than 9.73 % root-mean-square error by the appropriate choice of the critical void fraction in the bubbly layer. The present model shows comparable performance with the CHF look-up table of Groeneveld et al.

• 한국수자원학회논문집
• /
• 제44권2호
• /
• pp.157-167
• /
• 2011

본 연구에서는 복단면개수로및 불규칙한 하상을보이는 횡단면 상에서의 수위-유량곡선 및단위유량횡분포예측을 위한 유한요소모형을 개발하였다. 지배방정식은 정상류와 종방향 등류를 가정한 운동량방정식을 이용하며, 수면은 횡단면에 걸쳐 일정하다고 가정한다. 홍수터 식생의 영향을 반영하기 위해 식생항력이 지배방정식에 포함되었으며, 수치해를 구하기 위해 유한요소법을 적용하였다. 단면형상과 Manning의 조도계수, 식생정보, 종방향 하상경사를 입력자료로 수위-유량 곡선을 예측 가능하며, 주어진 수위에서의 흐름방향 단위유량의 횡방향 분포를 예측할 수 있다. 개발된 모형의 검증을 위해 실측자료 및 Darby and Thorne (1996)의 모형 결과, 그리고 비선형 k-$\epsilon$ 모형의 결과와도 비교하였다. 검증된 모형의 알고리즘을 2차원 모형의 상류단 경계조건 설정에 활용하여, 유입유량을 절점별 단위유량으로 분배시켰을 때와 그렇지 않았을 때의 결과를 비교하였다.

• 설비공학논문집
• /
• 제20권7호
• /
• pp.478-485
• /
• 2008

The extreme steam temperature deviation experienced in the superheater of a tangentially fired boiler can seriously affect its economic and safe operation. This temperature deviation is one of the main causes of boiler tube failures. The steam temperature deviation is mainly due to the thermal load deviation in the lateral direction of the superheater. The thermal load deviation consists of several causes. One of the causes is the non-uniform heat flow distribution of burnt gas on the superheater tube system. This distribution is very difficult to measure in situ using direct experimental techniques. So, we need thermal load model to estimate the tube temperature. In this paper, we propose a thermal load distribution model by using CFD analysis and plant data. We successfully predict the tube temperature and the steam flow rate in a final superheater system from the thermal load model and one dimensional heat-flow system analysis. The proposed model and analysis method would be valuable in preventing the frequent tube failure of the final superheater tubes.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2015년도 학술발표회
• /
• pp.439-439
• /
• 2015

The temporal and spatial relationship of the weather elements such as rainfall and temperature is closely linked to the streamflow simulation, especially, to the flood forecasting problems. For the study area, Imjin river basin, which has the specific characteristics in geography with river cross operation between North and South Korea, the meteorological information in the northern area is totally deficiency, lead to the inaccuracy of streamflow estimation. In the paper, this problem is solved by using the combination of global (such as soil moisture content, land use) and local hydrologic components data such as weather data (precipitation, evapotranspiration, humidity, etc.) for the model-driven runoff (surface flow, lateral flow and groundwater flow) data in each subbasin. To compute the streamflow in Imjin river basin, this study is applied the hydrologic model SURR (Sejong Univ. Rainfall-Runoff) which is the continuous rainfall-runoff model used physical foundations, originally based on Storage Function Model (SFM) to simulate the intercourse of the soil properties, weather factors and flow value. The result indicates the spatial variation in the runoff response of the different subbasins influenced by the input data. The dependancy of runoff simulation accuracy depending on the qualities of input data and model parameters is suggested in this study. The southern region with the dense of gauges and the adequate data shows the good results of the simulated discharge. Eventually, the application of SURR model in Imjin riverbasin gives the accurate consequence in simulation, and become the subsequent runoff for prediction in the future process.

• 한국수자원학회논문집
• /
• 제33권6호
• /
• pp.745-755
• /
• 2000

현재 우리나라에서 홍수조절 업무에 황용하고 있는 홍수관리시스템은 댐에서 조절이 불가능한 댐하류부 수문현상들을 고려하여 방류계획을 수립할 수 없으며, 예측 강우량에 의한 댐으로의 유출상황을 고려한 예비방류에 관한 지침이 마련되어 있지 않다. 따라서 본 연구에서는 댐의 제약조건 댐 상.하류의 유출상황을 고려하여 홍수기 댐을 운영 할 수 있는 모의기법에 의한 모형을 개발하였다. 개발된 모형(EV ROM이라 명명)은 댐에서 조절이 불가능한 댐하류 지류에 의한 하류 홍수제어 지점의 Cumulative Lateral Flow Hydrograph를 고려하여 방류계획을 수립한다. EV ROM에서는 댐하류 지역의 첨두홍수량 경감을 위하여 홍수제어지점의 수문곡선 상승부에서 예비방류를, 첨두부에서는 댐에 저류를 하였다가 수문곡선 하강부에 다시 방류를 수행하는 특징이 있다. EV ROM을 강우-유출모형에 결합하여 금강수계 대청댐을 중심으로 3개 홍수사상에 적용해 본 결과, 기존의 Rigid ROM이나 Technical ROM 보다 우수한 것으로 나타났다. 이는 본 연구에서 개발한 EV ROM이 댐 유역뿐만 아니라 댐하류 홍수제어지점의 수문상황을 동시에 고려하여 댐의 방류계열을 결정하기 때문이다. 따라서, 본 연구에서 개발된 EV ROM을 다양한 홍수사상에 적용, 예측강우량의 정확도 개선 및 프로그램의 보완이 이루어진다면, 현재보다 한차원 높아진 저수지운영을 기대 할 수 있을 것이다.

• Nuclear Engineering and Technology
• /
• 제52권9호
• /
• pp.1945-1954
• /
• 2020

Subchannel code is one of the effective simulation tools for thermal-hydraulic analysis in nuclear reactor core. In order to reduce the computational cost and improve the calculation efficiency, empirical correlation of turbulent mixing coefficient is employed to calculate the lateral mixing velocity between adjacent subchannels. However, correlations utilized currently are often fitted from data achieved in central channel of fuel assembly, which would simply neglect the wall effects. In this paper, the CFD approach based on spectral element method is employed to predict turbulent mixing phenomena through gaps in 3 × 3 bare tight lattice rod bundle and investigate the flow pulsation through gaps in different positions. Re = 5000,10000,20500 and P/D = 1.03 and 1.06 have been covered in the simulation cases. With a well verified mesh, lateral velocities at gap center between corner channel and wall channel (W-Co), wall channel and wall channel (W-W), wall channel and center channel (W-C) as well as center channel and center channel (C-C) are collected and compared with each other. The obvious turbulent mixing distributions are presented in the different channels of rod bundle. The peak frequency values at W-Co channel could have about 40%-50% reduction comparing with the C-C channel value and the turbulent mixing coefficient β could decrease around 25%. corrections for β should be performed in subchannel code at wall channel and corner channel for a reasonable prediction result. A preliminary analysis on fluctuation at channel gap has also performed. Eddy cascade should be considered carefully in detailed analysis for fluctuating in rod bundle.

• 대한조선학회논문집
• /
• 제47권6호
• /
• pp.782-786
• /
• 2010

Thrust deduction related to the prediction of power performance of a ship is rather resistance increase, and as a preliminary study for it forces upon a circular cylinder in a uniform flow of ideal fluid due to singularities located behind it are investigated. The circle theorem is used to get the complex velocity potential for the flow field under consideration, and the Blasius theorem is applied to obtain forces upon the circular cylinder. As singularities sinks, point vortices and dipoles and their combinations are treated. $\varepsilon$, standing for the strength of a singularity, and $\delta$, representing the distance between the cylinder and the singularity, are important small parameters for the resistance and lateral forces. For sinks or point vortices it is shown that the dimensionless forces upon the cylinder is O($\epsilon$) if $\epsilon$= O($\delta$) is assumed, and the same holds for dipoles if $\epsilon$= O(${\delta}^3$) is supposed. Forces upon the cylinder by a symmetric pair of sinks are greater than a single sink located at the central plane since there is an additional term due to cross effects, and the same is also valid for the case of dipole. Combination of dipole and a point vortex is also considered and a few new aspects are clarified.

• 한국항해학회지
• /
• 제24권3호
• /
• pp.123-132
• /
• 2000

In order to improve the ship maneuverability, It is important to estimate precisely the hydrodynamic coefficients of added mass forces acting on a ship especially in shallow waters, and simple methods for predicting such hydrodynamic forces Is also very desirable. In the previous paper using 3-Dimension potential flow theory, it has been demonstrated that potential calculation is available to estimate added mass coefficients. The present work is aimed at the suggestion of the simplified formulas for predicting the translation and lateral motion of added mass coefficients in shallow water. So, 3-D potential flow theory is also used to calculate the added mass coefficients in deep and shallow waters for Series 60 model which has 5 different kinds of block coefficients (0.6-0.8), SR196 model and T/S HANNARA. After some series computation, simplified formulas for Predicting the added mass force in shallow waters is suggested based on the computation results of Series 60 model. The formulas consist of the combination of principal dimensions and the water depth; d/B, Cb, d/H. The predicted results are compared with the Computation results for SR196 model and T/S HANNARA. The precision of predicted results by simplified formulas are good enough for the practical use. (d/B : draft-Breadth ratio, d/H draft-Water depth ratio, Cb : Block coefficients).

• Geomechanics and Engineering
• /
• 제11권2호
• /
• pp.235-252
• /
• 2016

This paper presents a new numerical solution of the ultimate lateral capacity of rectangular piles in clay. The two-dimensional plane strain finite element was employed to determine the limit load of this problem. A rectangular pile is subjected to purely lateral loading along either its major or minor axes. Complete parametric studies were performed for two dimensionless variables including: (1) the aspect ratios of rectangular piles were studied in the full range from plates to square piles loaded along either their major or minor axes; and (2) the adhesion factors between the soil-pile interface were studied in the complete range from smooth surfaces to rough surfaces. It was found that the dimensionless load factor of rectangular piles showed a highly non-linear function with the aspect ratio of piles and a slightly non-linear function with the adhesion factor at the soil-pile interface. In addition, the dimensionless load factor of rectangular piles loaded along the major axis was significantly higher than that loaded along the minor axis until it converged to the same value at square piles. The solutions of finite element analyses were verified with the finite element limit analysis for selected cases. The empirical equation of the dimensionless load factor of rectangular piles was also proposed based on the data of finite element analysis. Because of the plane strain condition of the top view section, results can be only applied to the full-flow failure mechanism around the pile for the prediction of limiting pressure at the deeper length of a very long pile with full tension interface that does not allow any separation at soil-pile interfaces.