• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.3
• /
• pp.222-227
• /
• 2010

ZnO nanorods array have been grown on the seed crystal coated Si(100) substrate by hydrothermal method. The growth, structural and optical properties of ZnO nanorods array were investigated with a variation of precursor concentration from 0.01 M to 0.04 M. The array density of grown ZnO nanorods per same area was increased with increasing the concentration of precursor solution. Vertically aligned ZnO nanorods with hexagonal wurtzite structure have highly preferred c-axis orientation along (002) lattice plane. Especially, ZnO nanorods array developed from 0.04 M precursor solution showed a diameter of about 85 nm and length of 1.2 {\mu}m$ without any crystallographic defects. The photoluminescence spectra of ZnO nanorods from heavier precursor concentration exhibited stronger UV emission around 380 nm corresponding with near-band-edge emission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.11
• /
• pp.1014-1019
• /
• 2006

The influence of the number of solution coatings on the densification of the PZT thick films was studied. PZT powder and PZT precursor solution was prepared by a sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The powder and solution of composition were (A) PZT(80/20)/PZT(20/80), (B) PZT(70/30)/PZT(30/70) and (C) PZT(60/40)/PZT(40/60), (D) PZT(52/48)/PT. The coating and drying procedure was repeated 4 times. And then the PZT precursor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 moth and the number of coating was repeated from 0 to 6. The porosity of the thick films was decreased with increasing the number of coatings and the PZT thick films with 6-times coated showed the dense microstructure and thickness of about $60{\mu}m$. A grain size was increased with increasing the coating number. All PZT thick films showed the typical XRD patterns of a typical perovskite polycrystalline structure. The relative dielectric constant of PZT thick films was improved 30-100% as the number of coatings.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1457-1462
• /
• 2007

A simple and facile sonochemical route was described for the fabrication of diameter-controlled ZnO nanorod arrays on Si wafers. The diameter of ZnO nanorods was controlled by the concentration of zinc cations and hydroxyl anions in aqueous precursor solution. At high concentration of the precursor solution, thick ZnO nanorod arrays were formed. On the contrary, thin ZnO nanorod arrays were formed at low concentration of the precursor solution. The average diameter of ZnO nanorods varies from 40 to 200 nm. ZnO nanorod arrays with sharp tip were also fabricated by the step-by-step decrease in precursor solution concentration. The crystal structure and optical characteristics of ZnO nanorods were investigated by transmission electron microscopy, X-ray diffraction, and photoluminescence spectroscopy. Growth mechanism of ZnO nanorod arrays was also proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05a
• /
• pp.69-72
• /
• 2003

Bi-2223 superconducting wires were fabricated by stacking, drawing process with different precursor powders and different heat-treatment histories. The precursor powders were 2 kinds of Pb content. And a part of the tapes were experienced pre-annealing process which caused tetragonal structure of Bi-2212 phase to orthorhombic structure of it was during drawing process. We confirmed the transformation of Bi-2212 phase from tetragonal structure to orthorhombic structure and reduction of second phases. XRD and DC magnetization analysis were performed in order to investigate the fraction of Bi-2223 phase in Bi-2223/Ag HTS tape. We could achieve best Ic of 70 A class at the Bi-2223/Ag tape using low Pb content of precursor powder and experienced pre-annealing process. DC magnetization analysis was useful to investigate the fraction of Bi-2223 phase in the Bi-2223/Ag tape.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.636-640
• /
• 2020

Due to the serious air pollution problem, interest in eco-friendly vehicles is increasing. Solving the problem of pollution will necessitate the securing of high energy storage technology for batteries, the driving force of eco-friendly vehicles. The reason for the continuing interest in the transition metal oxide LiMO₂ as a cathode material with a layered structure is that lithium ions reveal high mobility in two-dimensional space. Therefore, it is important to investigate the effective intercalation and deintercalation pathways of Li⁺, which affect battery capacity, to understand the internal structure of the cathode particle and its effect on the electrochemical performance. In this study, for the cathode material, high nickel Ni_0.8Co_0.1Mn_0.1(OH)₂ precursor is synthesized by controlling the ammonia concentration. Thereafter, the shape of the primary particles of the precursor is investigated through SEM analysis; X-ray diffraction analysis is also performed. The electrochemical properties of LiNi_0.8Co_0.1Mn_0.1O₂ are evaluated after heat treatment.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.915-920
• /
• 1996

Fine mullite precursor was prepared by colloidal sol-gel processes. Aluminum isopropoxide $[Al(i-OC_3H_7)_3]$ as a starting material of $Al_2O_3$ and silicic acid extracted by THF from sodium silicate as a starting material of $SiO_2$ were used. Sodium silicate was first acidified by dilute sulfuric acid to form silicic acid. ; followed by extraction using THF, Mullite precursor was synthesized by sol-gel processes from aluminum isopropoxide and sillicic acid considering the degree of extraction of Si and the removal efficiency of Na. The impurity content of silicic acid extracted by THF was below 0.04% Synthetic mullite precursor consisted of $3Al_2O_3{\cdot}2SiO_2$ and showd spherical particles of $0.05{\mu}m$ diameter and below 0.462% of impurites. The mullite precursor was characterized by EDS, XRD, TG/DSC SEM, FT-IR spectroscopy ICP and TEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1092-1098
• /
• 2006

The influence of the concentration of precursor solution and the number of solution coatings on the densification of the $Pb(Zr_xTi_{1-x})O_3$ (PZT) thick films was studied. PZT powder and PZT precursor solution were prepared by3 sol-gel method and PZT thick films were fabricated by the screen-printing method on the alumina substrates. The composition of powder and precursor solution were PZT(70/30) and PZT(30/70), respectively. The PZT precursor solution was spin-coated on the PZT thick films. A concentration of a coating solution was 0.5 to 2.0 mol/L[M] and the number of coating was repeated from 0 to 6. The XRD patterns of all PZT thick films shelved typical perovskite polycrystalline structure. The porosity of the thick films was decreased with increasing the number of coatings and 6-time coated films with 1.5 M showed the dense microstructure and thickness of about $60{\mu}m$. The relative dielectric constant of the PZT thick film was increased with increasing the number of solution coatings and the thick films with 1.5 M, 6-time coated showed the 698. The remanent polarization the 1.5 M and 6-time coated PZT thick films was $38.3{\mu}C/cm^2$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.2
• /
• pp.61-67
• /
• 2022

A metal salt solution was prepared from valuable metals (Ni, Co, Mn) recovered from a scrap of waste lithium secondary batteries, and an NCM811 precursor was synthesized from the solution. The effect on precursor formation according to reaction time was confirmed by SEM, PSA, and ICP analysis. Based on the analysis results, the electrochemical properties of the synthesized NCM811 precursor and the commercial NCM811 precursor were investigated. The Galvano charge-discharge cycle, rate performance, and Cycle performance were compared, and as a result, there was no significant difference from commercial precursors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.732-734
• /
• 2003

A solvothermal synthetic method to $BaTiO_3$ nanoparticle has been investigated in toluene solution with $BaTi(OR)_6$ as precursor. A precursor prepared from barium metal with toluene, isopropanol and titanium isopropoxide was used as a starting material. Weight ratio of precursor to solvent prepared in the mixture are 5/100, 10/100, 20/100 and 50/100wt%. At the weight ratio of 50/100wt%, $BaTiO_3$ butterfly twin crystalline(${\fallingdotseq}100nm$) was obtained after synthesis at $250^{\circ}C$ for 20hrs in an autoclave. X-ray diffraction and transmission electron microscopy showed that the product of 50/100wt% has crystallization. At 5/100, 10/100, and 20/100wt%, however, red colloidal solution was obtained after synthesis and crystalline phase of $BaTiO_3$ was not produced.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.5
• /
• pp.447-452
• /
• 2008

We synthesized nano-sized $La_{1-x}Sr_xCoO_3$ ($x=0.1{\sim}0.4$) cathode catalyst for the zinc air secondary batteries by citrate method, And we measured the cathode's electrochemical characteristics according to content of strontium compose the cathode catalyst. We controlled the pH of precursor solution by 10 in the process of manufacturing the precursor, We heat treated the prepared precursor at various calcination temperature ($500{\sim}900^{\circ}C$), and examined the optimum calcinations temperature by XRD analysis and electrochemical evaluation. We examined the ORR (oxygen reduction reaction) and OER (oxygen evolution reaction) performance of the prepared $La_{1-x}Sr_xCoO_3$ catalyst powder. When we consider ORR and OER performance simultaneously, $La_{0.7}Sr_{0.3}CoO_3$ catalyst has shown the best performance because of its lowest voltage deference between charge and discharge.