• 제목/요약/키워드: pre-splitting

검색결과 35건 처리시간 0.021초

암반사면의 절리빈도 특성에 따른 프리스플리팅 발파공법의 적용성 연구 (A Study on Applicability of Pre-splitting Blasting Method According to Joint Frequency Characteristics in Rock Slope)

  • 김신;이승중;최성웅
    • 화약ㆍ발파
    • /
    • 제28권2호
    • /
    • pp.1-16
    • /
    • 2010
  • 본 연구에서는 암반사면형성 작업시 최종벽면에 적용된 프리스플리팅(pre-splitting) 발파공법의 발파효과와 관련하여 발파 후 벽면의 암반손상이 장약된 폭약의 폭력 보다는 암반 내에 발달된 불연속면의 발달 형태에 따라 더 큰 영향을 보일 수 있음을 규명하였다. 이를 위하여 불연속면을 대표할 수 있는 절리에 대한 조사를 통해 발파 후 벽면 암반의 절리군 분포양상을 4가지 Case로 분류하고, 파쇄도 분석 영상처리시스템을 통해 벽면에 나타나는 암반블록의 크기 빈도를 비교 분석함으로써 벽면의 암반손상도를 파악하였다. 절리군이 1개 이하로 발달하는 경우, 분석된 블록의 크기 중 2,000mm 이상 되는 부분이 42%를 차지하여 프리스플리팅 발파공법의 효과를 뚜렷이 확인할 수 있었으며, 2~3개의 절리군이 일방향으로 발달하는 경우와 교차되면서 발달하는 경우, 블록의 크기는 1,000~2,000mm 사이에 각각 43.6% 및 35.8%의 빈도로 분포하는 것으로 나타나 프리스플리팅 발파공법에 의한 발파효율이 다소 떨어지는 양상을 보였다. 그러나 3개 이상의 절리군이 불규칙하게 발달하는 경우에는 블록의 크기가 250~500mm 사이에 35%의 빈도로 분포하고 1,000mm 이상의 크기에 대해서는 거의 나타나지 않는 양상을 보였다. 따라서 이러한 경우 프리스플리팅 발파공법에 의한 발파 효과는 거의 없이 일반적인 발파가 이루어졌다고 볼 수 있었다. 또한 PFC2D에 의한 발파수치해석결과, 암반 내부로의 손상영역 발생은 본 발파보다는 프리스플리팅 발파공법에 의해 직접적인 영향을 받을 수 있음을 확인하였으며, 따라서 향후 사면 형성을 위한 프리스플리팅 발파공법을 적용할 경우에는 사전 지표지질조사를 시행하여 절리를 비롯한 불연속면과 관련된 사항을 충분히 파악할 필요가 있으며, 시공진행에 따라 예상보다 많은 절리군이 나타날 경우에는 프리스플리팅 발파공법의 설계 조정이 필요할 것으로 판단된다.

선균열과 상부 심빼기를 이용한 환경 친화적 터널발파공법 (A Tunnel Blasting Method Favorable to the Environment, which Utilizes Pre-splitting & an Upper Center Cut.)

  • 김일중;김영석;기경철
    • 화약ㆍ발파
    • /
    • 제20권2호
    • /
    • pp.7-19
    • /
    • 2002
  • The cut is placed high up in the section, the 1st sloping holes below the cut, and divided all the holes located below the 1st sloping holes into a certain area with longitudinal section, to lower pollution made from tunnel blasting. With the sequential blasting machine, after I first blasted holes around the cut holes by a pre-splitting method, blasted the cut area and the 1st sloping holes. The 1st and 2nd sloping holes divided areas are initiated gradually to free face upwards made by the cut. Especially, I pre-splinted contour holes previous blast the before sloping holes from the contours. The ground vibration from the earth surface just over the advance face decreased about 42.0% compare with the down blasting method under the condition of equal charge weight per delay. I controlled the crack and over break of the mother rock by pre-splitting contour holes before blast the first sloping holes from the contours. The peak values of noise and air blast by blasting decreased about 10dB more than the down blasting method. the noise and air blast diminished gradually as a round. The throw distance of the fly rock was decreased about 55%.

STABLY PERIODIC SHADOWING AND DOMINATED SPLITTING

  • Lee, Keonhee;Lee, Manseob;Ahn, Jiweon
    • 충청수학회지
    • /
    • 제24권4호
    • /
    • pp.735-743
    • /
    • 2011
  • Let f be a diffeomorphism of a closed n-dimensional smooth manifold. In this paper, we introduce the notion of $C^1$-stably periodic shadowing property for a closed f-invariant set, and prove that for a transitive set ${\Lambda}$, if f has the $C^1$-stably periodic shadowing property on ${\Lambda}$, then ${\Lambda}$ admits a dominated splitting.

응력장을 고려한 프리스플리팅 공법의 균열발생 원리에 대한 연구 (A Study on the Crack-propagation Mechanism of Pre-splitting Method with Consideration of Stress Field)

  • 윤지선;우택규;김민우;장영민
    • 화약ㆍ발파
    • /
    • 제27권2호
    • /
    • pp.1-11
    • /
    • 2009
  • 본 연구에서는 프리스플리팅 적용 시 심발 발파를 통해 먼저 자유면을 확보한 후 이에 따른 응력변화를 관찰함으로서 최 외곽영역에서 균열형성을 함에 있어서의 유리함을 판단하고자 하며 균열형성이 용이한 조건을 찾고자 한다. 수치해석에서는 터널 내 최소주응력 방향을 고려했으며 수치해석 결과 응력의 방향변화는 가압하중의 크기변화에 큰 영향이 있음을 확인할 수 있었고, 차응력이 증가할수록 균열이 증가하는 경향을 확인하였다. 모형실험결과 응력장을 고려한 프리스플리팅공법 적용으로 기존 프리스플리팅 공법에 비해 균열 제어가 용이하고, 이를 통해 이완영역 축소를 기대할 수 있으며 또한 새로운 개념의 프리스플리팅 공법의 적용성을 판단하였다.

이미지 데이터베이스에서 인터벌을 이용한 객체분류를 위한 분리 방법 (Splitting Rules using Intervals for Object Classification in Image Databases)

  • 조준서;최준수
    • 정보처리학회논문지D
    • /
    • 제12D권6호
    • /
    • pp.829-836
    • /
    • 2005
  • 정확한 객체 분류를 위한 분리 기준을 지정하기 위한 방법은 의사결정수들(decisions trees) 사이에 주요한 이슈이다. 이 논문은 최적의 분리 지점을 찾기 위해 분류에 대한 새로운 분리방법을 기술하고 있다. 모든 시작점 값들(threshold values)을 검색함으로 제공되는 기존의 분리방법들과 다르게, 이 논문에서는 미리 지정된 인터벌들의 확률을 기반으로 하는 분리방법을 제안하고 있다 제시한 방법은 사용자가 인터벌의 수를 조정함으로써 트리의 정확도를 통제할 수 있도록 할 수 있으며, 제기된 분리방법을 이미지 객체 인식하기 위한 특징추출을 수치화함으로써 검색되는 일련의 이미지 데이터에 적용하였다.

Effect of ground granulated blast furnace slag on time-dependent tensile strength of concrete

  • Shariq, M.;Prasad, J.
    • Computers and Concrete
    • /
    • 제23권2호
    • /
    • pp.133-143
    • /
    • 2019
  • The paper presents the experimental investigations into the effect of ground granulated blast furnace slag (GGBFS) on the time-dependent tensile strength of concrete. The splitting and flexural tensile strength of concrete was determined at the ages of 3, 7, 28, 56, 90, 150 and 180 days using the cylindrical and prism specimens respectively for plain and GGBFS concrete. The amount of cement replacement by GGBFS was 0%, 40% and 60% on the weight basis. The maximum curing age was kept as 28 days. The results showed that the splitting and flexural tensile strength of concrete containing GGBFS has been found lower than the plain concrete at all ages and for all mixes. The tensile strength of 40 percent replacement has been found higher than the 60 percent at all ages and for all mixes. The rate of gain of splitting and flexural tensile strength of 40 percent GGBFS concrete is found higher than the plain concrete and 60 percent GGBFS concrete at the ages varying from 28 to 180 days. The experimental results of time-dependent tensile strength of concrete are compared with the available models. New models for the prediction of time-dependent splitting and flexural tensile strength of concrete containing GGBFS are proposed. The present experimental and analytical study will be helpful for the designers to know the time-dependent tensile properties of GGBFS concrete to meet the design requirements of liquid retaining reinforced and pre-stressed concrete structures.

유도슬롯과 주입공 배열을 이용한 수압암반절개 현장 실험 (Field Tests of Hydraulic Rock Splitting Technique Using Arrays of Injection Holes with Guide Slots)

  • 박종오;우익
    • 지질공학
    • /
    • 제29권4호
    • /
    • pp.405-415
    • /
    • 2019
  • 수압암반절개에서 유도된 균열은 자유면에서 지반의 최소주응력에 수직인 방향인 자유면과 평행한 방향으로 형성되거나, 기존에 발달한 미세균열의 영향을 많이 받는다. 본 연구에서는 흑운모화강암 사면에서 시추공 축과 평행한 방향으로 유도슬롯을 생성하여 이중패커의 압력 및 인터벌 구간에 수압을 주입하는 수압암반절개 실험을 수행하고 그 결과를 분석하였다. 실험 결과, 이중패커 압력 및 인터벌 구간 내의 주입으로 형성된 균열은 유도슬롯 방향을 따라 미세하게 나타났으며, 일부 균열은 시추공을 가로질러 연장되었다. 따라서 수압암반절개는 절개할 방향으로 유도슬롯을 생성하여 보다 많은 유량을 주입하면 효율적인 유도균열 조절이 가능할 것으로 판단된다.

Spinous Process-Splitting Hemilaminoplasty for Intradural and Extradural Lesions

  • Lee, Young-Seok;Kim, Young-Baeg;Park, Seung-Won
    • Journal of Korean Neurosurgical Society
    • /
    • 제58권5호
    • /
    • pp.494-498
    • /
    • 2015
  • Objective : To describe a novel spinous process-splitting hemilaminoplasty technique for the surgical treatment of intradural and posterior epidural lesions that promotes physiological restoration. Methods : The spinous process was split, the area of the facet lamina junction was drilled, and en bloc hemilaminectomy was then performed. After removing intradural and posterior epidural lesions, we fitted the previously en bloc-removed bone to the pre-surgery same shape, and held it in place with non-absorbable sutures. Surgery was performed on 16 laminas from a total of nine patients between 2011 and 2014. Bony union of the reconstructed lamina was assessed using computed tomography (CT) at 6 months after surgery. Results : Spinous process-slitting hemilaminoplasty was performed for intradural extramedullary tumors in eight patients and for ossification of the ligament flavum in one patient. Because we were able to visualize the margin of the ipsilateral and contralateral dura, we were able to secure space for removal of the lesion and closure of the dura. None of the cases showed spinal deformity or other complications. Bone fusion and maintenance of the spinal canal were found to be perfect on CT scans. Conclusion : The spinous process-splitting hemilaminoplasty technique presented here was successful in creating sufficient space to remove intradural and posterior epidural lesions and to close the dura. Furthermore, we were able to maintain the physiological barrier and integrity after surgery because the posterior musculature and bone structures were restored.

Flows over Concave Surfaces: Development of Pre-set Wavelength Görtler Vortices

  • Winoto, S.H.;Tandiono, Tandiono;Shah, D.A.;Mitsudharmadi, H.
    • International Journal of Fluid Machinery and Systems
    • /
    • 제1권1호
    • /
    • pp.10-23
    • /
    • 2008
  • The development of pre-set wavelength G$\ddot{o}$rtler vortices are studied in the boundary-layer flows on concave surfaces of 1.0 and 2.0 m radius of curvature. The wavelengths of the vortices were pre-set by thin wires of 0.2 mm diameter placed 10 mm upstream and perpendicular to the concave surface leading edge. Velocity contours were obtained from velocity measurements using a single hot-wire anemometer probe. The most amplified or dominant wavelength is found to be 15 mm for free-stream velocity of 2.1 m/s and 3.0 m/s on the concave surface of R = 1 m and 2 m, respectively. The velocity contours in the cross-sectional planes at several streamwise locations show the growth and breakdown of the vortices. Three different regions can be identified based on the growth rate of the vortices. The occurrence of a secondary instability mode is also shown in the form of mushroom-like structures as a consequence of the non-linear growth of the G$\ddot{o}$rtler vortices. By pre-setting the vortex wavelength to be much larger and much smaller than the most amplified one, the splitting and merging of G$\ddot{o}$rtler vortices can be respectively observed.