• Journal of IKEEE
• /
• v.20 no.4
• /
• pp.373-377
• /
• 2016

This paper presents a low power boost converter using offset controlled Zero Current Sensor (ZCS) control for thermoelectric energy harvesting.[1] [5] Offset controlled ZCS uses adjustable pre-offset that is controled by 6bit code each connected gate of NMOS for switching. Offset controlled ZCS demonstrates an efficiency that is higher than using analog comparator ZCS and that is smaller area than using delay line ZCS. Experimentally, the offset controlled ZCS system consumes 10 times less power than analog comparator ZCS based system at similar performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.935-942
• /
• 2006

The performance of ROF systems can be severely degraded due to nonlinear effects in the channel. Also, Orthogonal Frequency Division Multiplex(OFDM), as a standard for broadband wireless and mobile internet networks, is being proposed for deployment with ROF systems to facilitate the total performance of a system. In this paper, at first, the performance of the OFDM-based RoF system with a Mach-Zehnder(MZ) modulator distortion effects has been analyzed at 5.8GHz. Evaluation of mean-squared error of the proposed OFDM-RoF system was carried out to compare with the conventional single carrier system based RoF link after the modulator distortion case and also for fixed signal to noise ratio(SNR) of 20dB using undistorted OFDM signal. Nominal and offset baising pre-distortion techniques are applied in proposed system to linearize the OFDM-RoF link. Finally, a comparison between the aforementioned pre-distortion techniques applied showed important observation in terms of distortion-free dynamic range and SNR to choose offset pre-distortion technique for our proposed system.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.3
• /
• pp.347-353
• /
• 2017

We present a STT-MRAM read-circuit which mitigates the performance degradation caused by offsets from device mismatches. In the circuit, a single current source supplies read-current to both the data and the reference cells sequentially eliminating potential mismatches. Furthermore, an offset-free pre-amplification using a capacitor storing the mismatch information is employed to lessen the effect of the comparator offset. The proposed circuit was implemented using a 130-nm CMOS technology and Monte Carlo simulations of the circuit demonstrate its effectiveness in suppressing the effect of device mismatch.

• Computers and Concrete
• /
• v.18 no.6
• /
• pp.1135-1151
• /
• 2016

For investigating the effect of the pre-existing joints on the initiation pattern of hydraulic fractures, the numerical simulation of circular holes under internal hydraulic pressure with a different pattern of the joint distributions are conducted by using a finite element code, FRANC2D. The pattern of hydraulic fracturing initiation are scrutinized with changing the values of the joint length, joint offset angle. The hydraulic pressures with 70% of the peak value of borehole wall breakout pressure are applied at the similar models. The simulation results suggest that the opening-mode fracture initiated from the joint tip and propagated toward the borehole for critical values of ligament angle and joint offset angle. At these critical values, the crack grow length is influenced by joint ligament length. When the ligament length is less than 3 times the borehole diameter the crack growth length increases monotonically with increasing joint length. The opening-mode fracture disappears at the joint tip as the ligament length increases.

• Journal of Communications and Networks
• /
• v.9 no.3
• /
• pp.312-318
• /
• 2007

In this paper, we propose the optimal offset-time decision (OOD) algorithm which can effectively reduce the pre-transmission delay compared to the perfect isolation model, and can also be extended to general n priority classes while the target loss probability of each class is guaranteed for the variable offered load. In order to drive the OOD algorithm, we first analyze the loss probability of each priority class through class aggregation and iteration method; the analytic results obtained through the proposed algorithm are then validated with results garnered from extensive simulation tests.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.179-185
• /
• 2019

In this paper, we have studied narrow-band analog pre-distortion linearization technique using UHF 400 MHz band 20 W power amplifier. The analog pre-distorter used the SC1894 radio frequency power amplifier linearizer(RFPAL) provided by MAXIM Corp and through the look-up table technique confirmed the intermodulation distortion(IMD) performance and the adjusted channel leakage ratio(ACLR) improvement for bandwidth below 1 MHz which does not operate on existing chips. In the 400 MHz (400 ~ 500 MHz) band, IMD performance and the ACLR improvement of up to 17.46 dB based on 1-channel offset and up to 16.6 dB based on 2-channel offset were confirmed. In the system requiring the same linearity, we confirmed power efficiency improvement of 12.41% at output power of over 40 W.

• Korean Journal of Remote Sensing
• /
• v.33 no.2
• /
• pp.159-169
• /
• 2017

The Satellite Electro-Optic Payload System needsspecial requirements with the conditions of limited power consumption and the space environment of solar radiation. The acquired image quality should be mainly depend on the GSD (Ground Sampled Distance), SNR (Signal to Noise Ratio), and MTF (Modulation Transfer Function). On the well-manufactured sensor level, the thermal noise is removed on ASP (Analog Signal Processing) using the CDS (Corrective Double Sampling); the noise signal from the image sensor can be reduced from the offset signals based on the pre-pixels and the dark-pixels. The non-uniformity shall be corrected with gain, offset, and correction parameter of the image sensor pixel characteristic on the sensor control system. This paper describes the SNR enhancement method of the satellite EOS payload using the mentioned noise remove processes on the system design and operation, which is verified by tests and simulations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.8B
• /
• pp.514-524
• /
• 2005

In optical burst switching(OBS) networks, the ingress edge router assembles packets in the same class queue into the appropriate size of burst. A burst control packet(BCP) is generated for channel reservation of corresponding data burst and sent earlier than the corresponding data burst with an offset time. Offset time is determined considering the number of hops from source to destination and the required quality of service(QoS). After offset time, the burst data is passed through tile pre-configured optical switches without any O/E/O conversion. But a failure in OBS networks may lead to the loss of bursts until the ingress nodes receive the failure indication signal. This results in a significant degradation in QoS. Therefore, in this paper, we propose a fault-tolerant node architecture based on sub-carrier multiplexing to reduce the effects of failure in OBS networks. The Performance of the proposed fault-tolerant node architecture exhibits considerable improvement as compared with the previous ones.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.534-537
• /
• 2006

The jacking of cantilever before key segment closure has been introduced to offset the long term forces caused by creep and shrinkage. In this paper, the behavior of structural system with the jacking force in approach bridge of Incheon Bridge was reviewed. The introduction of jacking force effectively offset the long term horizontal forces and allows economic substructure member design.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.983-984
• /
• 2008

This paper proposes a variable break that can offset prediction error as well as a pre-selection methods, based on the variable break, for enhanced unit selection. In Japanese, a sentence consists of several APs (Accentual phrases) and MPs (Major phrases), and the breaks between these phrases must predicted to realize text-to-speech systems. An MP also consists of several APs and plays a decisive role in making synthetic speech natural and understandable because short pauses appear at its boundary. The variable break is defined as a break that is able to change easily from an AP to an MP boundary, or from an MP to an AP boundary. Using CART (Classification and Regression Trees), the variable break is modeled stochastically, and then we pre-select candidate units in the unit-selection process. As the experimental results show, it was possible to complement a break prediction error and improve the naturalness of synthetic speech.