• Journal of Industrial Technology
• /
• v.15
• /
• pp.203-208
• /
• 1995

This paper suggests the three dimensional steady state searching techniques of hard disk/head system, which has some skew angle with flexure. In order to analyze the steady state behaviors of magnetic head slider, the localized Knudsen number and the localized bearing numbers are sued. For finding the steady state of magnetic head slider under the pre-loaded condition, I proposed multi-dimensional Newton-Raphson method which traces the equilibrium position of magnetic head slider, which has 3-degrees of freedom, using Jacobian matrix. The multi-dimensional Newton-Raphson method is very efficient technique for finding the steady state position of magnetic head slider because it approaches to the equilibrium position with changing three parameters simultaneously.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.476-481
• /
• 2001

In this paper, based on the developed dynamic model of a vacuum circuit breaker mechanism, the development of the new circuit breaker with less energy mechanism is focused. The energy flow analysis of the original mechanism is carried out to show where the elastic potential energies of pre-loaded springs are transmitted. Through energy flow analysis, the concept design of the new circuit breaker with less energy mechanism is proposed, and then the detailed design is carried out through the design process based on the verified dynamic model. Comparing simulation results with experiment using a high-speed camera, the appropriateness of the proposed design procedures for the rapid circuit breaker mechanism is shown.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.27 no.2
• /
• pp.312-316
• /
• 2013

Caffeine is a thermogenic agent that can be used in weight loss products. In order to achieve a sustained release of caffeine, silk fibroin (SF) film was uses as carrier. It has been shown that the loading method of caffeine into SF film affected the uniform distribution of caffeine in the SF film. When caffeine was added directly into SF solution, gelation has been occurred immediately and prevented the uniform distribution of caffeine. On the other hand, caffeine was dissolved in methanol in order to load the caffeine in SF film and crystallize the SF film at the same time. However, due to the fast evaporation of methanol, caffeine was recrystallized on the surface of SF film rather than penetrating into the film. Finally, caffeine was loaded into pre-crystallized SF film and uniform distribution of caffeine could be achieved. There was an initial burst of caffeine during the first 15 min, but after that a sustained release was achieved.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.47-53
• /
• 2001

Power Circuit Breaker uses a variable-speed cam mechanism actuated by pre-loaded spring force. This paper presents the optimal design procedure for a variable-speed cam mechanism based on the dynamic model of a complete spring-actuated cam system. The optimal cam is compared with an original cam. Simulation results show that the dynamic behaviors of the designed cam are superior to those of the original cam.

• Nuclear Engineering and Technology
• /
• v.53 no.7
• /
• pp.2295-2303
• /
• 2021

To investigate wall-thinning impact on axial load resistance of Zircaloy-4 cladding rods after a LOCA transient, axial tensile samples have been machined on as-received tubes with reduced thicknesses between 370 and 580 ㎛. After high temperature oxidation under steam at 1200 ℃ with measured ECR ranging from 10 to 18% and water quenching, machined samples were axially loaded until fracture. These tests were modeled using a fracture mechanics approach developed in a previous study. Fracture stresses are rather well predicted. However, the slightly lower fracture stress observed for wall-thinned samples is not anticipated by this modeling approach. The results from this study confirm that characterizing the axial load resistance using semi-integral tests including the creep and burst phases was the best option to obtain accurate axial strengths describing accurately the influence of wall-thinning at burst region.

• Earthquakes and Structures
• /
• v.23 no.5
• /
• pp.463-472
• /
• 2022

Reinforced concrete (RC) beam column joints (BCJ) have mostly exhibited poor seismic performance during several past earthquakes, typically due to the poor-quality concrete or lack of reinforcement detailing typical of pre-code design practice. The present study is motivated towards numerical simulation and seismic fragility assessment of one such RC-BCJ. The BCJ is loaded to failure and strengthened using Ultra High Performance-Hybrid Fiber Reinforced Concrete (UHP-HFRC) jacketing. The strengthening is performed for four different BCJ specimens, each representing an intermediate damage state before collapse. viz., slight, moderate, severe, and collapse. From the numerical simulation of all the BCJ specimens, an attempt is made to correlate different modelling and design parameters of the BC joint with respect to the damage states. In addition, seismic fragility analysis of the original as well as the retrofitted damaged BCJ specimens show the relative enhancement achieved in each case.

• The Korean Journal of Physiology
• /
• v.20 no.1
• /
• pp.79-88
• /
• 1986

In an attempt to observe the effects obtained by the regular physical training, nine soldiers performed regularly the rope-skipping for nine weeks. All subjects were healthy and did not experience any special military training Programs. During the course of the training, their cardiopulmonary functions were measured in the resting and the Post-exercise recovery periods, and the values were compared with ones of the pre-trained. The test exercises loaded to the subjects were rope-skipping and step-rising & falling. The results obtained were as follows: 1) By the training, heart rates decreased very significantly in the resting and post-exercise recovery periods. And the effects began to bring out at the early stage, about the 7th day. 2) As the duration of the training increased, the systolic blood pressures decreased meaningfully in the resting and recovery periods. 3) Only in the early recovery phase after the exercise of the rope·skipping, the respiration rates decreased significantly by the training. 4) The lighter the intensity of the test exercise loaded was, the more prominent the effect of the physical training on the cardiopulmonary functions was. The above results suggest that the 9 week training of the rope-skipping would bring about the enhancement of the cardiopulmonary functions.

• Journal of Korea Water Resources Association
• /
• v.52 no.12
• /
• pp.1087-1098
• /
• 2019

In this study, we developed an integrated urban river data platform that collects, cleans, and provides data for urban river management. The urban river integrated data platform has the function of collecting data provided by various institutions using the Open API service. The collected data is purified through pre-processing and loaded into a database. The collected data can be reviewed and analyzed using a visualization system and provided through the Open API, so that it can be used as individual input data by combining them in the urban river model. In addition, the development system for real-time data was developed to apply real-time data to urban river models. Through this, users will be able to reduce the time and effort required for data collection, pre-processing and input data construction, thereby increasing efficiency and scalability in the development of urban river models and systems.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.3
• /
• pp.7-13
• /
• 1993

Fracture behavior of pre-cracked compact tension specimens made of AISI 4130 steel was investigated using acoustic emission (AE) and ultrasonic C-scan measurements. While each specimen was loaded up to a certain level, various acoustic emission parameters were recorded together with the crack opening displacement (COD). An elastic-plastic finite element analysis was performed to calculate COD and the damage (plastic) zone size ahead of crack tip. Ultrasonic C-scans, in a pulse-echo, immersion mode, were done for mapping the damage zone size. The agreement between the finite element results and the measured COD was satisfactory. Based on AE results, the test specimens were found to show ductile behavior. The slope of the total ringdown counts vs. COD curve was useful to determine the crack initiation. The preliminary C-scan images showed evidence of changes in the amplitude of ultrasonic signal in the damaged region, and the shape and size of the damage zone matched qualitatively with the finite element results. A further work on the damage zone sizing was also pointed out.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.7
• /
• pp.56-62
• /
• 2019

The high-precision laser scriber carries out scribing alumina ceramic substrates for manufacturing ultra-small chip resistors. The ceramic substrates are loaded, aligned, scribed, transferred, and unloaded. The entire process is fully automated, thereby minimizing the scribing cycle time of the ceramic substrates and improving the throughput. The scriber consists of the laser optical system, pick-up module of ceramic substrates, pre-alignment module, TH axis drive work table, automation module for substrate loading / unloading, and high-speed scribing control S/W. The loader / unloader unit, which has the greatest influence on the scribing cycle time of the substrates, carries the substrates to the work table that carries out the cutting line work by driving the X and Y axes as well as by adsorbing the ceramic substrates. The loader / unloader unit consists of the magazine up / down part, X-axis drive part for conveying the substrates to the left and right direction, and the vision part for detecting the edge of the substrate for the primary pre-alignment of the substrates. In this paper, the laser scribing machining simulation is performed by applying the instrument mechanism of each component module. Through this study, the scribing machining process is first verified by analyzing the process operation and work area of each module in advance. In addition, the scribing machining process is optimized by comparing and analyzing the scribing cycle time of one ceramic substrate according to the alignment stage module speed.