• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.114-123
• /
• 2018

Wind power tower (WPT) has been used to augment the performance of vertical axis wind turbine (VAWT). However, the performance of the WPT depends on several design parameters, such as inner and outer radius, or number of guide walls. Therefore, an experimental study was conducted to investigate efficient design parameters on the WPT. A wind tunnel was utilized and its test section dimension was 2m height and 2.2m width. One story model of the WPT was manufactured with seven guide walls and a VAWT was installed within the WPT. Three different sizes of guide walls were applied to test with various design parameters. The power coefficients were measured along the azimuthal direction in a state of equal inlet velocity in order to compare its performance relatively. The experimental results showed that the gap between the inner radius of the WPT and the rotating radius of the VAWT was a major parameter to improve the performance of VAWT within the WPT.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.1
• /
• pp.51-58
• /
• 2015

In order to decrease the size of a switch mode power supply, high switching frequency can be an efficient way to reduce the size of passive components in the converter. In this paper, a 500-kHz high-frequency LLC resonant converter is proposed with an accurate design method of magnetizing inductance, as well as the relationship between the switching frequency and the size of the passive components. Simulation and experimental results are presented to verify the proposed methods and equations, including the temperature data of each passive and active device of the converter. Using those results, dominant power losses in the prototype converter under 500-kHz high-frequency operation are investigated, compared with the results from a 100-kHz converter. In addition, operating waveforms and power conversion efficiency will be shown to obtain design considerations for the high switching frequency LLC resonant converter.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.110-114
• /
• 2008

In this paper, high efficient class F power amplifier with dual band has been realized. Dual band power amplifier have used modify stub matching for single FET, center frequency 2.14GHz and 5.2GHz respectively. Dual band amplifier is 32.65dBm output power, gain 11dB and PAE 36% at the 2.14GHz, 7dB gain at the 5.2GHz. Design of a dual band class F power amplifier using harmonic control circuit. The measured are 9.9dB gain, 30dBm output power and PAE 55% at the 2.14GHz, 11.7dB gain at the 5.2GHz. This paper is being used the load-pull method and it maximizes output power and it is using the only one transistor in the paper. As a result, this research will obtain a dual band high PAE power amplifier.

• KEPCO Journal on Electric Power and Energy
• /
• v.3 no.2
• /
• pp.89-97
• /
• 2017

The substation is a critical node in the power network where power is transformed in the power generation, transmission and distribution system. The IEC 61850 is a global standard which proposes efficient substation automation by defining interoperable communication and data modelling techniques. In order to achieve this level of interoperability and automation, the IEC 61850 (Part 6) defines System Configuration description Language (SCL). The SCL is an XML based file format for defining the abstract model of primary and secondary substation equipment, communications systems and also the relationship between them. It enables the interoperable exchange of data during substation engineering by standardizing the description of applications at different stages of the engineering process. To achieve the seamless interoperability, multi-vendor devices are required to adhere completely to the IEC 61850. This paper proposes an efficient algorithm required for verifying the interoperability of multi-vendor devices by checking the adherence of the SCL file to specifications of the standard. Our proposed SCL validation algorithm consists of schema validation and other functionalities including information model validation using UML data model, the Vendor Defined Extension model validation, the User Defined Rule validation and the IED Engineering Table (IET) consistency validation. It also integrates the standard UCAIUG (Utility Communication Architecture International Users Group) Procedure validation for quality assurance testing. Our proposed algorithm is not only flexible and efficient in terms of ensuring interoperable functionality of tested devices, it is also convenient for use by system integrators and test engineers.

• The KIPS Transactions:PartD
• /
• v.18D no.1
• /
• pp.45-56
• /
• 2011

The importance of low-power embedded system is being increased. The studies on low-power system have been performed in issues of hardware architecture and operating system. However because the behaviors of software control the working of hardware devices, the power analysis of software is one of critical issues in energy-efficient embedded system development. This paper proposes a technique to extract tasks from software design models with considering power consumption. We first define the criteria for task extraction, and then propose the way to separate out the task from UML 2.0 design models. Our technique can provide the chance to reduce the power consumption as well as to fulfill the performance requirement in the early phase of software development.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.89-94
• /
• 2009

Aerial application using an agricultural unmanned helicopter was suggested for an alternative against current pesticide application methods. Centrifugal clutches play important roles in the performance and safety of the helicopter operation. A previous study analyzed and verified the power transfer theory of the guide type centrifugal clutch. Based on the clutch theory, optimal designs of the clutch became possible and feasible using a simulation method. Design criteria of the clutch were the power transfer capacity of 24.66 kW(33.5 PS) at the rated engine speed and the engaging range speed of 3,000${\sim}$3,500 rpm. Various designs were accomplished using the simulation. An optimal clutch was simulated by determining the values of spring constant and mass of friction sector, which were 94,700 N/m and 123.7 g, respectively. The design performed the power capacity of 24.86 kW(33.8 PS) and engagement speed of 3,069 rpm, meeting the design criteria. Using the designed clutch, an efficient transfer of the power would be possible for the unmanned agricultural helicopter.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.10
• /
• pp.4865-4885
• /
• 2019

We propose a FPGA based design that performs real-time power-efficient analysis of heterogeneous sensor data using adaptive ANN on edge gateway of smart military wearables. In this work, four independent ANN classifiers are developed with optimum topologies. Out of which human activity, BP and toxic gas classifier are multiclass and ECG classifier is binary. These classifiers are later integrated into a single adaptive ANN hardware with a select line(s) that switches the hardware architecture as per the sensor type. Five versions of adaptive ANN with different precisions have been synthesized into IP cores. These IP cores are implemented and tested on Xilinx Artix-7 FPGA using Microblaze test system and LabVIEW based sensor simulators. The hardware analysis shows that the adaptive ANN even with 8-bit precision is the most efficient IP core in terms of hardware resource utilization and power consumption without compromising much on classification accuracy. This IP core requires only 31 microseconds for classification by consuming only 12 milliwatts of power. The proposed adaptive ANN design saves 61% to 97% of different FPGA resources and 44% of power as compared with the independent implementations. In addition, 96.87% to 98.75% of data throughput reduction is achieved by this edge gateway.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.619-624
• /
• 2015

Owing to miniaturization and low-power electronics, mobile, implanted, and wearable devices have become the main trends of electronics during the past decade. There has been much research regarding energy harvesting to achieve battery-free or self-powered devices. The optimal design problems of a double-pendulum kinetic-energy harvester from human motion are studied in this paper. For the given form factor, the weight of the harvester, and the known human excitation, the optimal design problem is solved using a dynamic non-linear double-pendulum model and an electric generator. The average electrical power was selected as the performance index for the given time period. A double-pendulum harvester was proven to be more efficient than a single-pendulum harvester when the appropriate parameters were used.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.101-103
• /
• 1998

New transmission lines are gradually constructed with high voltage and power for increase of electric power demands. And electric losses that are produced in line are increased. we made the algorithm for low loss wire and developed the computer program that makes loss of electric wire to be decreased for efficient power transmission. Electric wire is designed not to be decreased electrical and mechanical properties than that of existing electric wire.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.39-42
• /
• 1989

The limitations of high-power electrical lasers due to heating of the gas and the instability of the glow discharge can be alleviated by the flow of the lasing medium. In order to achieve high power and efficient laser, we are developing a fast-axial flow CO2 laser. We describe here the classification of gas-discharge CO2 lasers according to the cooling methods of the lasing medium and the design features of the fast-axial flow CO2 laser.