• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(1)
• /
• pp.459-464
• /
• 1996

The 3-D power distribution synthesis scheme was implemented in Totally Integrated Core Operation Monitoring System (TICOMS), which is under development as the next generation core monitoring system. The on-line 3-D core power distribution obtained from the measured fixed incore detector readings is used to construct the hot pin power as well as the core average axial power distribution. The core average axial power distribution and the hot pin power of TICOMS were compared with those of the current digital on-line core monitoring system, COLSS, which construct the core average axial power distribution and the pseudo hot pin power. The comparison shows that TICOMS results in the slightly more accurate core average axial power distribution and the less conservative hot pin power. Therefore, these results increased the core operating margins. In addition, the on-line 3-D power distribution is expected to be very useful for the core operation in the future.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.181-186
• /
• 2005

Because of advanced control technology, Shop floor control system of various kinds of equipment and machinery need a web based remote monitoring to control process efficiently. This paper presents the development of Operation Control System. Operation Control System(OCS) is based on intelligent web monitoring, so that OCS is improved the working condition for the line of heat treatment process and the product's quality. The developed OCS is consisted of Atmega128(MCU) based on embedded system, running the data logging of the line of heat treatment process. Web monitoring system is based on CS8900 ethernet controller and TCP/IP for remote monitoring responsibility between a server and clients and controlling the progress of entire system. The developed OCS is implemented on the line of heat treatment process and shows the improvement of environment condition, product's quality and efficiency of process line.

• 한국정밀공학회지
• /
• 제22권6호
• /
• pp.83-89
• /
• 2005

Most domestic fossil power plants have exceeded 100,000 hours of operation with the severe operating condition. Among the critical components of fossil power plant, high temperature steam pipe systems have had a many problems and damage from unstable displacement behavior because of frequent start up and shut down. In order to prevent the serious damage and failure of the critical pipe system in fossil power plants, 3-dimensional displacement measurement system was developed for the on-line monitoring. Displacement measurement system was developed with a use of a LVDT type sensor and two rotary encoder type sensors. This system was installed and operated on the real power plant successfully.

• 한국인터넷방송통신학회논문지
• /
• 제12권4호
• /
• pp.189-194
• /
• 2012

수배전 무효전력 보상 감시 제어시스템은 수배전단에 설치된 유도 모터, 또는 아크 용접기 등과 같은 유도성 부하에서 발생되는 지상무효전력을 보상하고 역률의 개선, 전압 강하의 경감, 전력손실을 감소 시켜줌으로써 전력설비 계통을 경제적이고 안정적으로 운영하도록 도와준다. 그리고 이러한 시스템은 중앙전력감시반이 획득한 수변전설비의 운전상태 및 계측 Data를 근거로 역률 및 위상각을 분석하여 기준 위상각이상으로 전압과 전류의 위상차가 발생 되었을 경우, 무효전력 보상장치의 ON/OFF제어를 수행하여 효율적인 계통관리가 가능하도록 한다. 본 연구에서는 능동데이터베이스를 이용하여 무효전력 보상장치 감시제어 시스템을 구현하는 방안을 제시함으로써, 공장 부하의 지상무효전력이 급격한 증가로 인한 역률 저하, 전압 강하, 손실 발생 등의 징후 발생 시 이에 대한 대처를 사용자(operator)의 개입 없이 데이터베이스 스스로 수행하도록 함으로써 인위에 의한 실수를 최소화 하도록 하였다.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.182-187
• /
• 2017

Synchronous generators have been significantly applied in large-scale power plants and its monitoring systems are additionally established to sequentially observe states and outputs. We develop a computer based monitoring device for three-phase synchronous power generators in this paper. First, a test-bed of such generator system is created and then a interface board is constructed to transfer electric signals including the output voltage and the current from generators into a computer system via a data acquisition device. Its RMS(root-mean-square) values are continuously shown on a screen of computer systems and its time-histories graphs are additionally illustrated under a graphic user interface(GUI) mode. Lastly, we carry out real-time experiments using the generator system with the monitoring device to demonstrate its reliability and superiority by comparing results of a generic power analyzer which is well-used in measuring various power systems practically.

• 한국정보통신학회논문지
• /
• 제16권10호
• /
• pp.2185-2191
• /
• 2012

기존의 인버터에 대한 모니터링은 로컬컴퓨터나 웹 모니터링 등을 이용하여 모니터링을 하고 있다. 그러나 본 논문에서는 블루투스 통신을 이용하여 사용자가 편리한 위치에서 컴퓨터를 사용하지 않고도 태양광 인버터를 원격 모니터링 가능한 시스템을 구현하였다. 제안한 시스템은 인버터 프로토콜을 이용하여 인버터의 원하는 정보를 무선 통신으로 모니터링 할 수 있게 설계 하였다. 또한 태양광 인버터의 고장시 블루투스 고장이력과 시각을 기록할 수 있도록 하였다. 마지막으로 본 논문에서 제안한 시스템이 실험을 통해 좋은 성능을 보여주었고 또한 상용화의 가능성을 제시해 주었다.

• 산업기술연구
• /
• 제21권A호
• /
• pp.105-110
• /
• 2001

A continuous and reliable electrical energy supply is the objective of any power system operation. A transmission line is the part of the power system where faults are most likely to happen. This paler describes the use of wavelet transform for analyzing power system fault transients in order to determine the fault location. Synchronized sampling was made possible by precise time receivers based on GPS time reference, and the sampled data were analyzed using wavelet transform. This paper describes a fault location monitoring system and fault locating algorithm with GPS, DSP processor, and data acquisition board, and presents some experimental results and error analysis.

• 대한원격탐사학회지
• /
• 제30권3호
• /
• pp.383-397
• /
• 2014

Information technology advances are allowing conventional surveillance systems to be combined with mobile communication technologies, creating ubiquitous monitoring systems. This paper proposes monitoring system that uses smart camera technology. We discuss the dependence of interior orientation parameters on calibration target sheets and compare the accuracy of a three-dimensional monitoring system with camera location calculated by space resectioning using a Digital Surface Model (DSM) generated from stereo images. A monitoring housing is designed to protect a camera from various weather conditions and to provide the camera for power generated from solar panel. A smart camera is installed in the monitoring housing. The smart camera is operated and controlled through an Android application. At last the accuracy of a three-dimensional monitoring system is evaluated using a DSM. The proposed system was then tested against a DSM created from ground control points determined by Global Positioning Systems (GPSs) and light detection and ranging data. The standard deviation of the differences between DSMs are less than 0.12 m. Therefore the monitoring system is appropriate for extracting the information of objects' position and deformation as well as monitoring them. Through incorporation of components, such as camera housing, a solar power supply, the smart camera the system can be used as a ubiquitous monitoring system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.309-311
• /
• 1995

Recently, a power supply system of the telecommunication equipments with monitoring function has been widely studied. In the power supply system which is apart from the central station, it is required to check and test the operating states of the system at the central station. In this paper, the power supply system with monitoring function is discussed. In the system, the Full-Bridge converter is designed as a power supply and it has the ratings of DC 280-340V input and DC 48V, 480W output. And the monitoring part of the system is composed of a voltage and current sensing unit A/D converter, I/O card, and a personal computer. The operating states of the system is monitored by checking the voltage and current variation at input and output, and it is represented by graphical modes. By conducting the experiment, it is confirmed that the operating states of the system is well monitored.

• ETRI Journal
• /
• 제43권3호
• /
• pp.459-470
• /
• 2021

This paper presents a low-cost prototype for monitoring online the maximum power produced by a domestic photovoltaic (PV) system using Internet of Things (IoT) technology. The most common tracking algorithms (P&O, InCond, HC, VSS InCond, and FL) were first simulated using MATLAB/Simulink and then implemented in a low-cost microcontroller (Arduino). The current, voltage, load current, load voltage, power at the maximum power point, duty cycle, module temperature, and in-plane solar irradiance are monitored. Using IoT technology, users can check in real time the change in power produced by their installation anywhere and anytime without additional effort or cost. The designed prototype is suitable for domestic PV applications, particularly at remote sites. It can also help users check online whether any abnormality has happened in their system based simply on the variation in the produced maximum power. Experimental results show that the system performs well. Moreover, the prototype is easy to implement, low in cost, saves time, and minimizes human effort. The developed monitoring system could be extended by integrating fault detection and diagnosis algorithms.