• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1061-1065
• /
• 1999

The effect of particle size of coating powder and coating temperature on the thickness of coating layer formed on metal surface was studied by using XRD, SEM and EDXS. Coating powder was separated according to particle size by 3 steps and coating temperatures were varied from $950^{\circ}C$ to $980^{\circ}C$. Calorizing carried out at air and Ar conditions for 5 hrs, respectively. XRD result show that $Al_2O_3$ and AlN were formed during calorizing at air condition. The thickness and Al content of coating layer increased as the particle size of coating powder decreased and coating temperature increased.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.1
• /
• pp.5-13
• /
• 2022

In tropical regions, lateritic soil is frequently used in road embankment. However, it is one of the sources of road failure owing to its low strength. Generally, cement and lime are used as stabilizers for lateritic soil, but they are not environmentally friendly. Some studies try to use eggshells, for they are food waste and share the same chemical composition as lime. Previous researchs have shown that eggshell powder could enhance the strength of lateritic soil. This research investigated the effect of particle size of the eggshell powder and the effect of the protein-membrane presence in the eggshell on stabilizing capacity of soil. Through laboratory tests, unconfined compressive strength was examined for various particle sizes. The particle size of eggshell powder ranging between 150 ㎛ and 88 ㎛ was appropriate size that made an excellent stabilizer at 3% concentration. On the other hand, the protein-membrane reduced the stabilizing ability of the eggshell powder when the content of eggshell powder is less than 4% in soil. Numerical analysis of road embankment was performed based on the results obtained in the laboratory tests. It is shown that the eggshell powder has improved the stability of the sub-base of the road embankment.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.235-239
• /
• 1998

Ultrafine $SnO_2$ powder was prepared by the diffusion mixing gas-phase reaction of $SnCl_4$(g) and water vapor. The effects of reaction variables, such as the chloride partial pressure, the reaction temperature, and the residence time is the reactor, on the powder size were examined systematically. Calculated concentration and distribution of chemical species, using the Burke-Schumann diffusion mixing model, were compared with the experimetal results. The effects of the reaction variables on the powder size were also discussed qualitatively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.441-444
• /
• 2008

Ultra high performance concrete (UHPC) in this study is composed of sand, cement, silica fume, siliceous powder, superplasticizer and steel fiber. UHPC is composed of fine mineral particles below 0.5mm in diameter. In general, siliceous powder improves the mechanical properties of concrete by physical and chemical effect. Physical effect is related with filling interior voids which weaken the mechanical properties and chemical effect with reaction of $SiO_2$ with cement hydrates in a condition of high temperature and pressure. We evaluated the effect of siliceous powder's particle size on the mechanical properties of ultra high performance concrete in air pressure and $90^{\circ}C$ steam curing condition. siliceous powder's particle size in this study is in the range of $2{\mu}m$ to $26{\mu}m$. Fluidity in a fresh concrete, compressive strength, ultimate strain, elastic modulus and flexural strength in a hardened concrete was evaluated. We could find out that the smaller siliceous powder's particle size is, the better the fluidity and strength properties.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.480-481
• /
• 2006

The n-type $(95%Bi_2Te_3-5%Bi_2Se_3)$ compound was newly fabricated by gas atomization and hot extrusion, which is considered to be a mass production technique of this alloy. The effect of powder size on thermoelectric properties of 0.04% $SbI_3$ doped $95%Bi_2Te_3-5%Bi_2Se_3$ alloy were investigated. Seebeck coefficient $({\alpha})$ and Electrical resistivity $(\rho)$ increased with increasing powder size due to the decrease in carrier concentration by oxygen content. With increasing powder size, the compressive strength of $95%Bi_2Te_3-5%Bi_2Se_3$ alloy was increased due to the relative high density. The compound with ${\sim}300\;{\mu}m$ size shows the highest power factor among the four different powder sizes. The rapidly solidified and hot extruded compound using $200[\sim}300{\mu}m$ powder size shows the highest compressive strength.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.157-162
• /
• 2001

Rheological characteristics of Sm-Co type plastic magnet compound for powder injection molding process were investigated with the variation of the magnetic powder size, their relative contents and volume fraction using the mixture of fine and coarse powder. Shear viscosity of Sm-Co type compound was decreased with increasing the size of coarse powder due to the increase of powder packing density. However, the smaller the average size of fine powder resulted in the higher viscosity of compound due to the increase of agglomeration force. In case of mechanically milled Sm-Co type powder, the viscosity of compound with the mixture of coarse powder of 125∼75 ㎛ and fine powder of average size of 4.9 ㎛ greatly depends on their relative contents and shows a minimum value at the 60 % coarse powder fraction. This means that the compound shows a maximum packing density at the 60% coarse powder fraction. Compound viscosities satisfied well the rheological model with the volume fraction of magnetic powder, and maximum volume fraction of magnetic powder in Sm-Co type compound for powder injection molding was about 66%.

• Journal of Powder Materials
• /
• v.10 no.1
• /
• pp.57-62
• /
• 2003

The effect of bedding on the microstructure of $Si_3N_4$ added with ultra-fine SiC was investigated. The bedding and the addition of ultra-fine SiC effectively inhibited grain growth of $Si_3N_4$ matrix grain. The microstructures of the specimens sintered with bedding powder consisted of fine-grains as compared with the specimens sintered without bedding powder. In addition, the grain size and the difference of grain size between the specimens sintered with bedding and without bedding was reduced with increasing SiC content. Some ultra-fine SiC particles were trapped in the $Si_3N_4$ grains growed. The number of SiC particles trapped in the $Si_3N_4$ grains increased with increasing the grain growth. When ultra-fine SiC particles were added in the $Si_3N_4$ ceramics, the strength was improved but the toughness was decreased, which was considered to be resulted from the decrease of the grain size.

• Journal of the Korean Ceramic Society
• /
• v.25 no.5
• /
• pp.465-472
• /
• 1988

Alpha alumina powder with fine particle size and narrow particle size distribution was prepared by precipitation method using Al2(SO4)3.18H2O as a starting material. The alpha alumina powder was prepared by calcining aluminum hydroxide which was formed under various pH values. The sinterabilityof alpha alumina powder and the effect of MgO on the sinterability of alpha alumina powder were investigated. The sinterability of alpha alumina powder was the order of pH=10≒pH11>pH=7≒pH9, and alpha alumina obtained from boehmite which was prepared by precipitation method reached to 97.5% of theoretcal density by the pressureless sintering. The effect of MgO on volume shrinkage of alumina was very slight in the initial sintering stage but remarkable in the final sintering stage. It was also found that MgO controlled effectively the grain growth of alumina.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.55-62
• /
• 2010

This paper investigates the shear properties of waste tire-bottom ash mixture with various particle size of waste tire powder. Test specimens were prepared at 5 different percentages of waste tire powder content (i.e., 0%, 25%, 50%, 75%, 100% by weight of the dry bottom ash), and with three different particle sizes of waste tire powder (i.e., 0.1 mm~2.0 mm, 0.9 mm~5 mm and 2 mm~10 mm). In this study several series of direct shear tests were carried out. The experimental results indicate that the mechanical characteristics of waste tire-bottom ash mixture are strongly influenced by the particle size as well as waste tire powder content. It is shown that the shear strength and internal friction angle of waste tire-bottom ash mixture decrease with an increase in waste tire powder content. However, the shear strength and internal friction angle of the mixture increase due to interlocking effect between waste tire powder and bottom ash as the particle size of waste tire powder increases.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.105-106
• /
• 2007

Microstructure and hardness of metallic powder of Cu was studied after high pressure torsion (HPT) with 10 torsions and high pressure of 6 GPa. The size Cu grain decreases drastically after HPT and reaches the nano size range. During HPT, Cu powder increases hardness and Hall-Petch hardening, due to the decreasing grain size. In this study, effect of HPT on the hardness of Cu powders and consolidation with Nanocrystalline of the work reported here. The results indicated that Cu powder has a beneficial effect on homogeneous deformation, reducing grain size.