• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1404-1409
• /
• 2007

Polymers for laser sintering were needed in order to fabricate the articles with the three-dimensional duplication equipment of SLS (selective laser sintering) process. The thermal properties, particle size, distribution, and shape of polymer powder had a close relation with the processibility of laser sintering. In this study, we prepared new polymer powders with uniform size and higher bulk density by wet process. Wet process consists of several finely-controlled steps such as dissolution, nucleation, propagation and crystallization. Several additives were added to improve the thermal, rheological, and flow properties.

• 전기학회논문지
• /
• 제59권7호
• /
• pp.1272-1275
• /
• 2010

The Cu powder was prepared in distilled water. It has a wide range of size distribution. The submicron-sized particles in the Cu powder were removed by using continuous type centrifugal separator. The average particle size after classification was approximately 50nm. The XRD analysis showed that pure Cu phase and oxide phase ($Cu_2O$)weremixedinthepowderpreparedbythismethod.

• 한국세라믹학회지
• /
• 제36권7호
• /
• pp.742-750
• /
• 1999

화학기상응축법을 이용한 TiO2 나노분말합성시 전구체 주입속도 및 산소 반응기체유량의 변화에 따른 나노입자의 형성과정을 분말특성의 관점에서 조사하였다. 기상합성반응의 주요 열역학, 동역학적 인자인 과포화도, 충돌율, 체류시간의 상기 두 공정변수에 대한 의존성을 이론적으로 평가하였고, 이를 0.376, 0.742 m//min의 두 전구체 주입속도 조건에서 산소유량을 1에서 2slm까지 변화시키며 합성한 TiO2 나노분말의 특성과 관련하여 분석하였다 모든 조건에서 합성된 TiO2 분말은 20~30 nm의 크기를 갖는 미세한 anatase 상과 극소량의 rutilc상이 혼합되어 서로 느슨한 결합을 하고 있었다 전구체 주입속도가 0.376m//min의 경우, 전반적인 입도와 응집도는 0.742 m//min에 비해 작았으며, 산소유량이 증가할수록 체류시간과 충돌율이 감소하여 형성된 TiO2 분말의 입도는 감소하였다. 또한 산소유량 증가에 따른 과포화도의 감소는 분말형성과정과 기구에 영향을 미치는 것으로 판단되나, 정확한 분석을 위해서는 각각의 독립적인 열역학 및 동역학적 변수 조건하에서의 면밀한 고찰이 요구되었다.

• 한국식품영양학회지
• /
• 제35권1호
• /
• pp.16-33
• /
• 2022

The quality characteristics and antioxidant activity of Tteokbokkidduk alone or supplemented with 3%, 6%, 9%, and 12% wheat bran powder were assessed, to increase use of the wheat bran by-product of wheat milling. The moisture content, pH, and starch elution of Tteokbokkidduk increased with increasing wheat bran powder, while the water absorption rate did not. The L color value decreased and the a and b values increased with increasing wheat bran powder. Scanning electron microscopy of Tteokbokkidduk prepared with 0% and 3% wheat bran powder revealed uniform pore size distribution. In terms of texture profile analysis, hardness and chewiness increased, while cohesiveness decreased with increased content of wheat bran powder. Acceptance was highest for samples with 6% wheat bran powder. Quantitative description analysis (QDA) revealed increased brownness, roughness, nutty, bitterness, astringency, savory character, and hardness, and decreased adhesiveness, springiness, and chewiness with increased wheat bran powder. Principal component analysis (PCA) revealed highest overall acceptance of samples prepared with 6% wheat bran powder, reflecting the relatively low values of detrimental sensory characteristics. Antioxidant activities of Tteokbokkidduk increased as wheat bran powder content increased. The addition of 6% wheat bran powder resulted in excellent Tteokbokki in terms of acceptance, quality, and antioxidant activity.

• 한국분말재료학회지
• /
• 제4권1호
• /
• pp.42-47
• /
• 1997

It was investigated whether mechanical alloying (MA) processing could be more effective to the formation of metallic composite powder in Cu-C system. Elemental powder mixtures of Cu-70vo1.%C were mechanically alloyed with an attritor in an argon atmosphere and microstructural evolution was examined by X-ray diffraction analysis, scanning electron microscopy and transmission electron microscopy. It has been found that even with the high volume fraction of immiscible graphite in Cu-C system, the refinement with a few ten nanometer size as well as the highly uniform distribution of copper phases have been achieved by the MA processing.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1264-1265
• /
• 2006

Study about the feasibility and effect of high-energy ball milling on a specific Mg alloy under protection medium of alcohol was presented via comparing with conventional vacuum milling. More fine particles with wider powder size distribution but more irregular shape were shown of the powder milled under alcohol. No obvious oxide was revealed from the two kinds of Mg alloy powders with limited milling time. And since slip induced in a preferential direction, the (002) texture was formed in the Mg alloy powders at the initial stage of alcohol milling. More O and Fe contaminants were introduced into the powders milled under alcohol according to the EDS analysis.

• 한국세라믹학회지
• /
• 제31권1호
• /
• pp.55-61
• /
• 1994

Mn-Zn ferrite powder was obtained by wet method that was to be coprecipitated the metal ions of Fe2+, Mn2+ and Zn2+ with alkali solution. The target composition of the ferrite powder was 52 mol% Fe2O3, 24 mol% MnO, and 24 mol% ZnO, that was based on the region of high permeability. And the other ferrite powder was prepared by the dry method that was to be mixed the metal oxides as the above chemical composition. The wet method was compared with dry method for the powder properties and the electromagnetic characteristics of sintered cores. The synthesized powder by wet method was smaller particle size, narrower particle distribution, and higher purity than that of dry method. The initial permeability of sintered sample prepared by the wet method was 14000~28000, on the other side, 9000~15500 in case of the dry method.

• 열처리공학회지
• /
• 제34권2호
• /
• pp.60-65
• /
• 2021

In this study, the effect of pressure type and foaming agent on the microstructural change of Al foam produced by powder compact processing was investigated. Better foaming characteristic is easily obtained from extrusion process with strong plastic deformation and preheating than that by uniaxial pressing with preheating. In current powder compact foaming process using TiH2/MgH2 mixture as a foaming agent, a temperature of 670℃ and addition of 30% MgH2 in TiH2 foaming agent was chosen as the most suitable foaming condition. The aluminum (Al) foams with maximum porosity of around 70%, relatively regular pore size and distribution were successfully produced by means of the powder metallurgy method and extrusion process.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.360-365
• /
• 2006

The phase stability of tetragonal phase in Y-TZP was investigated in terms of the distribution of grain sizes and heat-treating atmosphere. Y-TZP with various grain sizes were prepared using duration time at $1600^{\circ}C$ as experimental parameter. Accumulated grain size distributions were built from the SEM micrographs and the amount of tetragonal phase were measured using XRD. Both results were compared to determine the critical grain size before and after heat-treatment in vacuum. The critical grain size drastically decreased compared with the small increase of average grain size due to the autocatalytic effect which critically affects the tetragonal to monoclinic phase transformation. After heat-treatment in reductive atmosphere critical grain size relatively increased due to the stabilization of tetragonal phase. The formation of oxygen vacancies during heat-treatment was ascribed to the increase of stability.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권3호
• /
• pp.372-381
• /
• 1995

본 논문에서는 분체 특성 평가 연구의 국제 동향과 입자형태, 입도분포, 비표면적, 분체밀도, 기공도, 화학분석 평가분야의 기본원리, 특히 측정시 변수들의 영향과 이러한 특성변화에 따른 전기적성질 변화에 대하여 간단히 언급을 하였다. 분체 특성평가분야의 연구는 선진국에 비해 낙후되어 있고 관심도 또한 낮은 형편이다. 이 분야의 학문적, 산업적인 중요점을 고려할 때, 분체 특성 평가에 대한 기초 및 응용연구가 활성화되었으면 한다.