• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• Applied Chemistry for Engineering
• /
• v.23 no.1
• /
• pp.1-7
• /
• 2012

In this article, I will introduce recent developments of environmental-friendly materials fabricated using atomic layer deposition (ALD). Advantages of ALD include fine control of the thin film thickness and formation of a homogeneous thin fim on complex-structured three-dimensional substrates. Such advantages of ALD can be exploited for fabricating environmental-friendly materials. Porous membranes such as anodic aluminum oxide (AAO) can be used as a substrate for $TiO_2$ coating with a thickness of about 10 nm, and the $TiO_2$-coated AAO can be used as filter of volatile organic compound such as toluene. The unique structural property of AAO in combination with a high adsorption capacity of amorphous $TiO_2$ can be exploited in this case. $TiO_2$ can be also deposited on nanodiamonds and Ni powder, which can be used as photocatalyst for degradation of toluene, and $CO_2$ reforming of methane catalyst, respectively. One can produce structures, in which the substrates are only partially covered by $TiO_2$ domains, and these structures turns out to be catalytically more active than bare substrates, or complete core-shell structures. We show that the ALD can be widely used not only in the semiconductor industry, but also environmental science.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.1-5
• /
• 2012

$Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ hollow fiber with o.d. 1.02 mm and i.d. 0.437 mm were fabricated by a phase-inversion spinning technique.The starting $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ precursor was synthesized by the polymerized complex method and then calcined at $900^{\circ}C$. As-prepared powder was dispersed in a polymer solution, and extruded as form of hollow fiber through a spinneret. Finallydense $Ba_{0.5}Sr_{0.5}Co_{0.8}Fe_{0.2}O_{3-{\delta}}$ hollow fiber membrane was obtained by sintering for 2 h at $1,080^{\circ}C$ for the application of oxygen separation. In addition, despite a very thin membrane with 0.58 mm, the BSCF hollow fiber membrane possessed a proper mechanical strength of 602.5 MPa.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.166-171
• /
• 2015

In this study, using solid-state and flux, $Y_3Al_5O_{12}:Er^{3+}\;(YAG:Er^{3+})$ powders were successfully synthesized at low temperatures. To analyze the crystallinity of powders according to the synthesis or non-synthesis of powders and powder calcination temperatures, X-ray diffraction (XRD) was measured. In the case of pure YAG, when YAG was analyzed using the general solid-phase method, it was calcined for 12 hours at $1400^{\circ}C$ and pure YAG phase could be obtained. But when $BaF_2$ was added to YAG, YAG was synthesized at lower temperature (1000^{\circ}C$). It was thus found that the synthesis temperature could be lowered by about $400^{\circ}C$. Also, when BaF2 with an optimal concentration was added to $YAG:Er^{3+}$, the particle shape and size according to synthesis temperatures were surveyed, and corresponding luminous intensity was discussed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.2
• /
• pp.108-113
• /
• 2013

Chalcopyrite material $CuInSe_2$ (CIS) is known to be a very prominent absorber layer for high efficiency thin film solar cells. Current interest in the photovoltaic industry is to identify and develop more suitable materials and processes for the fabrication of efficient and cost-effective solar cells. Various processes have been being tried for making a low cost CIS absorber layer, this study obtained the CIS nanoparticles using commercial powder of 6 mm pieces for low cost CIS absorber layer by high frequency ball milling and cryogenic milling. And the CIS absorber layer was prepared by paste coating using milled-CIS nanoparticles in glove box under inert atmosphere. The chalcopyrite $CuInSe_2$ thin films were successfully made after selenization at the substrate temperature of $550^{\circ}C$ in 30 min, CIS solar cell of Al/ZnO/CdS/CIS/Mo structure prepared under various deposition process such as evaporation, sputtering and chemical vapor deposition respectively. Finally, we achieved CIS nanoparticles solar cell of electric efficient 1.74 % of Voc 29 mV, Jsc 35 $mA/cm^2$ FF 17.2 %. The CIS nanoparticles-based absorber layers were characterized by using EDS, XRD and HRSEM.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06b
• /
• pp.259-279
• /
• 1996

최근 정보·전자산업의 발전으로 고 신뢰성 전자재료에 대한 수요가 증대되고 있으며 이러한 첨단산업의 기반의 될 신소재 중 전자세라믹스가 차지하는 비중이 그 대부분을 차지하고 있으며 이에 대한 수요와 기대가 점점 커지고 있다. 이러한 전자세라믹스는 유전재료, 자성재료, 압전재료, 도전성 재료 등으로 나뉘게 된다. 어떠한 분류에 들어가든 그 조성은 금속의 산화물 형태가 일반적이며 미세한 분말의 성형체를 소결(sintering) 함으로써 최종제품으로 완성된다. 이러한 전잣라믹스가 최근 요구되는 고 신뢰성, 고 밀도화를 달성하기 위해선 원료 분말 제조단계부터 제어가 필요하다. 원료분말의 균일·균질성과 그 입도는 소결특성 뿐만아니라 전기적 특성에도 큰 영향을 미치기 때문이다. 세라믹스의 분말제조 방법 중 일반적으로 사용되는 방법으로는 고상 산화물을 혼합하여 하소(calcination)한 후 분쇄하는 '고상합성법'과 금속의 염 또는 alkoxide 용액을 이용하여 화학적으로 제조하는 '습식 화학적 합성법'이 있다. 고상합성법은 합성온도가 높고 기계적 분쇄와 혼합에 의존하므로 균일·균질성이 떨어지고 분말크기를 1㎛ 이하로 만들기 힘들다. 반면에 습식화학적 합성법은 기계적인 분쇄와 혼합에선 얻을 수 없는 원자 혹은 분자단위의 균일한 혼합과 submicron 이하의 미세한 분말을 얻을 수 있다. 따라서 이러한 습식 화학적 합성으로 얻은 분말을 사용하면 미세한 입자의 특성으로 인해 소결온도를 낮출 수 있으며 균일한 미세구조와 균질한 조성을 갖게되어 기계적·전기적 물성증진도 가져올 수 있게 된다. 습식 화학적 분말합성법은 전술하였듯이 alkoxide의 가수분해를 이용하는 sol-gel 법과 금속의 염(salt) 용액을 이용하여, 화학적으로 화합물 침전을 얻거나 또는 공침전물(coprecipitate) 형태의 분말을 얻는, 침전법으로 나뉠 수 있다. 침전법의 근본원리는 pH 및 pCO3 등에 따른 이온종의 용해도 차이를 이용하는 것으로써 각 이온종에 따른 solubility product(ksp)를 이용하여 설명된다. 본 연구에서는 침전법을 사용한 Ba-, Pb-계 전자세라믹스의 분말합성에 대한 이론적 고찰과 공정개발 및 실험을 통한 물성증진 효과에 대해 알아보았다. 본 실험상의 전자세라믹스 조성은 강유전체, 세라믹반도체, 압효과에 대해 알아보았다. 본 실험상의 전자세라믹스 조성은 강유전체, 세라믹 반도체, 압전재료로 널리 사용되는 BaTiO3, PZT(PbZrO3-PbTiO3)와 수직 자기기록매체로 큰 가능성이 있으며 hard ferrite로 널리쓰이는 Ba-feerite(BaFe12O19)로써 수산화물 형태의 침전에 대한 기구(mechanism)와 물성에 대해 살펴보았다. 이러한 침전법에 의한 분말합성 과정에는 소결체의 물성에 영향을 미치는 pH 조절제나 원료에서 혼입될 수 있는 Na+, K+, Cl-, SO4- 등의 제거(washing 혹은 filtering)가 필수적이다. 그러나 침전법에서 얻게 되는 분말은 매우 미세하여 colloid를 형성하게 되며, 이러한 colloid 상태의 미세한 침전입자가 filtering media에 끼이게 되어 견고하면서도 상당한 부피를 가지는 filter cake을 형성하기 때문에 filtering에 많은 시간과 다량의 filtering agent (본 실험의 경우엔 증류수)가 필요하게 된다. 따라서 이러한 문제점을 해결하기 위하여 colloid 상태의 침전물을 얼렸다 녹이는 freezing process를 개발, 적용하여 그 원리 및 효과, 그로인한 분말형태를 관찰하여 보았다.

• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.165-170
• /
• 2003

M-type hexagonal BaFe$\sub$12/O$\sub$19/ ferrite powder was prepared by sol-gel process. The M-type hexagonal structure with ${\alpha}$ = 5.882 and c = 23.215 ${\AA}$ and its Curie temperature T$\sub$C/ was determined 780${\pm}$3 K. The isomer shifts of ,4f$_2$, 2a. 4f$_1$, 12k, and 2b were indicated 0.26, 0.24, 0.15, 0.25, and 0.24 mm/s, therefore, the valence states of the Fe ions were ferric (Fe$\^$3+/). By the law of approach to saturation (LAS), the effective anisotropy field H$\sub$A/ and crystalline anisotropy constant K$_1$ were estimated. The value of K$_1$ and H$\sub$A/ were K$_1$ = 2.5${\times}$10$\^6/erg/cm^3$ and H$\sub$A/ = 14 kOe, respectively.

• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.423-428
• /
• 2015

Impedancemetric $NO_x$ (NO and $NO_2$) gas sensors were designed with a stacked-layer structure and fabricated using $LaCr_xCo_{1-x}O_3$ (x = 0, 0.2, 0.5, 0.8 and 1) as the receptor material and $Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ plates as the solid-electrolyte transducer material. The $LaCr_xCo_{1-x}O_3$ layers were prepared with a polymeric precursor method that used ethylene glycol as the solvent, acetyl acetone as the chelating agent, and polyvinylpyrrolidone as the polymer additive. The effects of the Co concentration on the structural, morphological, and $NO_x$ sensing properties of the $LaCr_xCo_{1-x}O_3$ powders were investigated with powder X-ray diffraction, field emission scanning electron microscopy, and its response to 20~250 ppm of $NO_x$ at $400^{\circ}C$ (for 1 kHz and 0.5 V), respectively. When the as-prepared precursors were calcined at $700^{\circ}C$, only a single phase was detected, which corresponded to a perovskite-type structure. The XRD results showed that as the Co concentration of the $LaCr_xCo_{1-x}O_3$powders increased, the crystal structure was transformed from an orthorhombic phase to a rhombohedral phase. Moreover, the $LaCr_xCo_{1-x}O_3$ powders with $0{\leq}x<0.8$ had a rhombohedral symmetry. The size of the particles in the $LaCr_xCo_{1-x}O_3$powders increased from 0.1 to $0.5{\mu}m$ as the Co concentration increased. The sensing performance of the stack-structured $LaCr_xCo_{1-x}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensors was found to divide the impedance component between the resistance and capacitance. The response of these sensors to NO gas was more sensitive than that to $NO_2$ gas. Compared to other impedancemetric sensors, the $LaCr_{0.8}Co_{0.2}O_3/Li_{1.3}Al_{0.3}Ti_{1.7}(PO_4)_3$ sensor exhibited good reversibility and reliable sensingresponse properties for $NO_x$ gases.

• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.141-149
• /
• 1997

L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ powders were prepared by both GNP(Glycine-Nitrate Process) and solid state reaction method in various of calcination temperature(800-1000.deg. C) and time in air. Also, L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ cathode contacts on YSZ(Yttria-Stabilized Zirconia) substrate were prepared by screen printing and sintering method as a function of sintering temperature(1100-1450.deg. C) in air. Sintering behaviors have been investigated by SEM(Scanning Electron Microscope) and porosity measurement. Compositional and structural characterization were carried out by X-ray diffractometer and ICP AES(Inductively Coupled Plasma-Atomic Emission Spectrometry) analysis. Electrical characterization was carried out by the electrical conductivity with linear 4 point probe method. As the calcination period increased in solid state reaction method, L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ phase increased. Although L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ single phase was obtained only for 48hrs at 1000.deg. C, in GNP method it was easy to get single and ultra-fine L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ powders with submicron particle size at 650.deg. C for 30min. The particle size and thickness of L $a_{0.7}$S $r_{0.3}$Mn $O_{3}$ cathode contact by solid state reaction method did not change during the heat treatment, while those by GNP method showed good sintering characteristics because initial powder size fabricated from GNP method is smaller than that fabricated from solid state reaction method. Based on enthalpy change from thermodynamic data and ICP-AES analysis, it was suggested to make cathode contact in composition of (L $a_{0.7}$S $r_{0.3}$)$_{0.91}$ Mn $O_{3}$ which have little second phase (L $a_{2}$Z $r_{2}$ $O_{7}$) for high efficient solid oxide fuel cells applications. As (L $a_{0.7}$S $r_{0.3}$)$_{0.91}$Mn $O_{3}$ cathode contact on YSZ substrate was sintering at 1250.deg. C the temperature that liquid phase sintering did not occur. It was possible to obtain proper cathode contacts with electrical conductivity of 150(S/cm) and porosity content of 30-40%.m) and porosity content of 30-40%.

• Restorative Dentistry and Endodontics
• /
• v.18 no.1
• /
• pp.1-26
• /
• 1993

The purpose of this study was to investigate the effect of acid etching on the surface appearance and fracture toughness of five glass ionomer cements. Five kinds of commercially available glass ionomer cements including chemical curing filling type, chemical curing lining type, chemical curing metal reinforced type, light curing tilling type and light curing lining type were used for this study. The specimens for SEM study were fabricated by treating each glass ionomer cement with either visible light curing or self curing after being inserted into a rubber mold (diameter 4mm, depth 1mm). Some of the specimens were etched with 37% phosphoric acid for 0, 15, 30, 60, go seconds, at 5 minutes, 1 hour and 1 day after mixing of powder and liquid. Unetched ones comprised the control group and the others were the experimental groups. The surface texture was examined by using scanning electron microscope at 20 kV. (S-2300, Hitachi Co., Japan). The specimens for fracture toughness were fabricated by curing of each glass ionomer cement previously inserted into a metal mold for the single edge notch specimen according to the ASTME399. They were subjected to a three-point bend test after etching for 0, 30, 60, and 90 seconds at 5 minutes-, 1 hour-and 1 day-lapse after the fabrication of the specimens. The plane strain fracture toughness ($K_{IC}$) was determined by three-point bend test which was conducted with cross-head speed of 0.5 mm/min using Instron universal testing machine (Model No. 1122) following seven days storage of the etched specimens under $37^{\circ}C$, 100% humidity condition. Following conclusions were drawn. 1. In unetched control group, crack was present, but the surface was generally smooth. 2. Deterioration of the surface appearance such as serious dissolving of gel matrix and loss of glass particles occured as the etching time was increased beyond 15 s following Immediate etching of chemical curing type of glass ionomer cements. 3. Etching after 1 h, and 1 d reduced surface damage, 15 s, and 30s etch gave rough surface appearance without loss of glass particle of chemical curing type of glass ionomer cements. 4. Light curing type glass ionomer cement was etched by acid, but there was no difference in surface appearances according to various waiting periods. 5. It was found that the value of plane stram fracture toughness of glass ionomer cements was highest in the light curing filling type as $1.79\;MNm^{-1.5}$ followed by the light curing lining type, chemical curing metal reinforced type, chemical curing filling type and chemical curing lining type. 6. The value of plane stram fracture toughness of the chemical curing lining type glass ionomer cement etched after 5 minutes was lower than those of the cement etched after 1 hour or day or unetched (P < 0.05). 7. Light curing glass ionomer cement showed Irregular fractured surface and chemical curing cement showed smooth fractured surface.