• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.117-122
• /
• 2012

ZTO/GZO double layered films were prepared on unheated non-alkali glass substrates. ZTO films were deposited by RF/DC hybrid magnetron co-sputtering using ZnO (RF) target and $SnO_2$ (DC) targets, and then GZO films were deposited by DC magnetron sputtering using an GZO ($Ga_2O_3$:5.57 wt%) target. These films were post-annealed at temperature of 200, $300^{\circ}C$ in air and vacuum ambient for 30 min. In the case of post-annealing in air, ZTO/GZO double layer showed relatively low resistivity change, compared to GZO single layer. Furthermore, ZTO/GZO double layer revealed low WVTR, compared to GZO single layer. Therefore, it can be confirmed that ZTO film doing a role with barrier for water or oxygen diffusion.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1301-1304
• /
• 1994

ZnO transparent conducting oxide thin films have been prepared by Pyrosol deposition method. The effect of the Al doping with varying Al/Zn mole ratio and the post-deposition heat treatment on the electrical resistivity and optical transmittance of the prepared films have been investigated. From the experimental results, the ZnO:Al thin films with resistivity as low as $3{\times}10^{-3}{\Omega}cm$ and transmittance as high as 80% can be obtained by Al doping. Also We have found the annealing of the as-deposited ZnO film in vacuum leads to a substantial reduction in resistivity without affecting the optical transmittance and crystallographic orientation. However, the annealing effect of ZnO:Al thin films is smaller than ZnO films with respect to reduction in resistivity.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.168-168
• /
• 2001

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.105-105
• /
• 1994

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2006.11a
• /
• pp.17.2-17.2
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1277_1278
• /
• 2009

Amorphous oxide semiconductor $InGaZnO_4$(IGZO) is a very promising candidate of channel layer in transparent thin film trasisitor(TTFT) because of its high mobility and high transparency in visible light region. Amorphous IGZO films were deposited at room temperature on a fused silica substrate using pulsed laser deposition method. In-situ post annealing was carried out at 150-450C right after film deposition. The $O_2$ partial pressures during the deposition and the post annealing was fixed to 10mTorr. The electron transport properties of the amorphous IGZO films were improved by thermal annealing. The temperature range in which the improvement of the electrical properties, was 150C~300C.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.276-276
• /
• 2008

Transparent and conducting indium tin oxide (ITO) and ITO/Nickel/ITO(INI) multilayered films were prepared on glass substrates by a magnetron sputtering without intentional substrate heating. The RF(13.56MHz) and DC power were applied to ITO and Nickel target, respectively. The thickness of ITO, Ni and ITO films were kept constantly at 50, 5 and 45 nm. In order to consider the effect of post deposition vacuum annealing in vacuum on the physical and optoeletrical properties of INI films, optical transmittance, electrical resistivity, crystallinity of the films were analyzed. From the observed result, it may conclude that the optoelectrical properties of the INI films were dependent on the post deposition annealing. For the INI films annealed at $300^{\circ}C$, the films have a polycrystalline structure with (110), (200), (210), (211) and (300). The resistivity of the films were $4.0\times10^{-4}{\Omega}cm$ at room temperature. As the annealing($300^{\circ}C$), resistivity decreased to $2.8\times10^{-4}{\Omega}cm$. And also the optical transmittance decreased from 79 to 70 % at 550nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.329-332
• /
• 1999

In this paper, BST((Bao.&o,dTi0:3) thin films were deposited by the rf magnetron sputtering method on Pt/$SiO_2$/Si substrate. Pt, $RuO_2$, Ag, Cu films for the formation of top electrode were deposited on BST thm films. And then Top Electrodes/BST/Pt capacitors were annealed with rapid thermal annealing(RTA) at various temperature. We have investigated effect of post-annealing on the electrical properties such as dielectric constant and leakage current of the capacitors. It was found that electrical properties of the capacitors were greatly depended on the annealing temperatures as well as the materials of top electrodes. In BST thin films with Pt top electrode was annealed at $700^{\circ}C$. the dielectric constant was measured to the value of 346 at l[kHzl and the leakage current was obtained to the value of $8.76\times10^8$[A/$\textrm{cm}^2$] at the forward bias of 2[V].

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1483-1484
• /
• 2000

Dielectric thin films of PLT(Pb(La.Ti)O3) for the application of highly integrated memory devices have been deposited on Pt/Ti/SiO2/Si substrates in situ by pulsed laser deposition(PLD). We have systematically investigated the variation of grain sizes depending on the condition of post-annealing and the variation of deposition rate. Both in-situ annealing and ex-situ annealing have been compared depending on the annealing time. C-V measurement, ferroelectric properties, leakage current and SEM were performed to investigate the electrical properties and the microstructural properties of Pb(La,Ti)$O_3$ films.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.69-74
• /
• 2017

Effect of post-annealing treatment times at $200^{\circ}C$ on the peel strength of screen-printed Ag film/polyimide substrate were systematically investigated by $180^{\circ}$ peel test for thermal reliability assessment of printed interconnect. Initial peel strength around 16.7 gf/mm increased up to 29.4 gf/mm after annealing for 24hours, and then sharply decreased to 22.3, 3.6, 0.6, and 0.1 gf/mm after 48, 100, 250, and 500 hours, respectively. Ag-O-C chemical bonding as well as binder organic bridges formations seemed to be responsible for interfacial adhesion improvement after the initial annealing treatment, while excessive Cu oxide formation at Cu/Ag interface seems to be closely related to sharp decrease in peel strength for longer annealing times.