• 대한기계학회논문집B
• /
• 제40권2호
• /
• pp.85-91
• /
• 2016

내연기관 자동차와 달리 전기자동차는 배터리 폐열이 부족하여 실내 난방을 위해 추가적으로 PTC 히터를 사용하고 있지만 전력소모가 큰 단점이 있다. 최근 이러한 단점을 보완할 수 있는 히트펌프 적용에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 히트펌프의 운전특성 해석을 위해 MATLAB/SIMULINK$^{(R)}$환경에서 R134a 히트펌프 모델과 캐빈 모델을 개발하였다. 모델은 여름과 겨울에서 히트펌프의 작동 특성에 따른 실내 온도변화를 나타낼 수 있으며, 모델 검증은 구성품 수준에서 응축기와 증발기의 용량 비교를 수행하였다. 또한 동일한 냉방조건에서 캐빈온도 변화 비교를 통해 캐빈 모델을 검증하였다. 해석 결과 전동압축기 소비전력은 모든 외기온도 조건에서 PTC 히터 보다 낮은 것으로 나타났다. 또한 영하조건에서 히트펌프의 난방용량이 부족한 현상에 대해 폐열회수를 적용하여 효율적인 난방 작동을 할 수 있는 조건을 분석하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.104-106
• /
• 1995

A curious resistivity anomaly in high curie point barium-lead-titanate materials with positive temerature coefficient of resistivity (PTCR) has been observed just below the curie point, besides the normal PTCR anomaly. The additional resistivity anomaly was observed in the resistivity-temperature characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.251-251
• /
• 2007

A new type of a lead-free positive temperature coefficient of resistivity(PTCR) material. based on $(Bi_{1/2}Na_{1/2})TiO_3\;-\;BaTiO_3$ solid solution ceramics has been developed. The effect of $Nb_O_5$ and $Y_2O_3$ content on the electrical properties and the microstructure of (1-x) $(Bi_{1/2}Na_{1/2})TiO_3\;-\;x\;BaTiO_3$ (BNBT) ceramics made using a conventional mixed oxide process has been studied. The Curie Temperature was obviously increased with the increasing of $(B_{0.5}Na_{0.5})TiO_3$ content. The Y-doped BNBT ceramics(x=0.02) display low resistivity values of $10^2-10^3$ ohm*cm at room temperature and the Curie Temperature of $Tc=155^{\circ}C$.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.77-82
• /
• 1995

PTCR(Positive Temperature Coefficient of Resistivity) thermistor in thin film BaTiO$_{3}$ system was prepared by using radio frequency(13.56 MHz) and DC magnetron sputter equipment. Polycrystalline, surface structure, and R-T(Resistivity-Temperature) characteristics of the specimens were measured by X-ray diffraction(D-Max3, Rigaku, Japan), SEM(Scanning Electron Microscopy: M.JSM84 01, Japan), and insulation resistance measuring system (Keithley 719), respectively. Thin films characteristics of the thermistor showed different properties depending on the substrate even with the same sputtering condition. The thin film formed on the A1$_{2}$O$_{3}$ substrate showed a good crystalline and a low resistivity at below curie point. However, the thin films prepared on slide glass and Si wafer were amorphous. The thicknesses of the three samples prepared under the same process conditions were 700[.angs.], 637.75[.angs.], and 715[.angs.], respectively.

• Advanced Composite Materials
• /
• 제16권3호
• /
• pp.195-206
• /
• 2007

Carbon nanofiber (CNF)/unsaturated polyester resin (UPR) was prepared by a solvent evaporation method, and the temperature dependency of electrical conductivity was investigated. The CNF/UPR composites had quite a low percolation threshold due to CNF having a larger aspect ratio and being well dispersed in the UPR matrix. The positive temperature coefficient (PTC) was found in the CNF/UPR composites and it showed stronger effect around the percolation threshold. The electrical resistance of the CNF/UPR composites decreased and had lower temperature dependency with increasing numbers of thermal cycles.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.336-336
• /
• 2008

A positive temperature coefficient of electrical resistivity (PTCR) was investigated in a ferroelectric lead-free perovskite-type compound $(Bi_{0.5}K_{0.5})TiO_3$ within $BaTiO_3$-based solid solution ceramics. The electrical properties and the microstructure of (1-x) $BaTiO_3$ - x $(Bi_{0.5}K_{0.5})TiO_3$ (BBKT) ceramics made using a conventional mixed and have been synthesized by an ordinary sintering technique. The Curie temperature was obviously increased with increasing of $(Bi_{0.5}K_{0.5})TiO_3$ content. The BKT ceramics (x=0.05) sintered at $1400^{\circ}C$ for 4h display low resistivity values of $10^1-10^2$ ohm cm at room temperature, PTCR effect(jump) of 1.05*$10^3$, and the Curie temperature of $T_c=141^{\circ}C$.

• 항공우주기술
• /
• 제7권1호
• /
• pp.115-120
• /
• 2008

인공위성에 사용되는 온도 측정 센서는 서미스터(Thermistor) 와 AD590이 주로 많이 사용되고 있다. AD590은 IC chip으로 서미스터에 비해 고가이며 $1^{\circ}C$ 온도 변화에 출력 전류가 약 $1{\mu}A$ 변하는 특성을 가진다. 이에 비해 서 미스터는 온도 변화에 따라 저항 값이 변하므로 외부에서 전류나 혹은 전압 stimulus를 인가해 주어야한다. 또한 일반적으로 AD590에 비해 저가이며 NTC(Negative Temperature Coefficient)와 PTC(Positive Temperature Coefficient) 두 가지 형태의 센서가 사용되고 있다. 고 정밀 저궤도 지구관측용 인공위성의 경우 온도에 따른 카메라 구조물의 변형이 최종 영상 품질에 영향을 미치게 되므로 고 품질의 영상획득을 위하여 카메라 구조물의 정밀 온도 제어가 필수적으로 요구되며 이를 구현하기 위해서 매우 정확한 온도측정 요구조건이 주어지게 된다. 저궤도 인공위성의 경우 카메라 시스템에 부착된 온도센서의 측정 정확도 요구조건이 $0.3^{\circ}C$ 까지 요구되는 경우도 있다. 본 논문은 저 궤도 인공위성에 적용된 서 미스터의 온도 측정 정확도에 대한 분석 내용을 나타내었다.

• Carbon letters
• /
• 제7권2호
• /
• pp.87-96
• /
• 2006

This paper describes the physical properties of filled Nylon6 composites resin with nano-sized carbon black particle and graphite nanofibers prepared by melt extrusion method. In improving adhesions between resin and fillers, the surface of the carbon filler materials were chemically modified by thermo-oxidative treatments and followed by treatments of silane coupling agent. Crystallization temperature and rate of crystallization increased with increases in filler concentration which would act as nuclei for crystallization. The silane treatments on the filler materials showed effect of reduction in crystallization temperature, possibly from enhancement in wetting property of the surface of the filler materials. Percolation transition phenomenon at which the volume resistivity was sharply decreased was observed above 9 wt% of carbon black and above 6 wt% of graphite nanofiber. The graphite nanofibers contributed to more effectively in an increase in electrical conductivity than carbon black did, on the other hand, the silane coupling agent negatively affected to the electrical conductivity due to the insulating property of the silane. Positive temperature coefficient (PTC) phenomenon, was observed as usual in other composites, that is, temperature increase results conductivity increase. The dispersity of the fillers were excellently approached by melt extrusion of co-rotational twin screw type and it could be illustrated by X-ray diffraction and SEM.

• 한국재료학회지
• /
• 제20권12호
• /
• pp.654-660
• /
• 2010

The influences of Na and K content on the crystal phase, the microstructure and the electrical property of $BaTiO_3$-based thermistors was found to show typical PTC effects. The crystal phase of powder calcined at $1000^{\circ}C$ for 4hrs showed a single phase with $BaTiO_3$, and the crystal structure was transformed from tetragonal to cubic phase according to added amounts of Na and K. In XRD results at $43^{\circ}\sim47^{\circ}$, the $(Ba_{0.858}Na_{0.071}K_{0.071})(Ti_{0.9985}Nb_{0.0015})O_{3-\delta}$ showed (002) and (200) peaks but the $(Ba_{0.762}Na_{0.119}K_{0.119})(Ti_{0.9975}Nb_{0.0025})O_{3-\delta}$ showed (002), (020) and (200) peaks. In sintered bodies, those calcined at $600^{\circ}C$ rather than at $1000^{\circ}C$ were dense, and for certain amounts of Na and K showed rapid decreases in grain size. In relative permittivity, the curie temperature due to the transformation of ferroelectric phase rose with added Na and K but decreased in terms of relative permittivity. In the result of the R-T curve, the sintered bodies have curie temperatures of about $140^{\circ}C$ and the resistivity of sintered bodies have scores of $\Omega{\cdot}cm$; the jump order of sintered bodies was shown to be more than $10^4$ in powder calcined at $1000^{\circ}C$.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.17-22
• /
• 2014

Recently, the quick heating performance is an important issue in the car because engine power becomes so high. So car makers have been adapted the additional heating devices as like PTC(Positive Temperature Coefficient) heater. And the quick cooling performance is also important issue because its result is used in the IQS(Initial Quality Study). In this paper, control of the HVAC(Heating, Ventilation and Air Conditioning) intake door has been studied for the quick heating and cooling performance. Heating performance is improved $4.0^{\circ}C$ at $-20^{\circ}C$ ambient temperature after 20 minutes. And cooling performance is improved $1.5^{\circ}C$ at $35^{\circ}C$ ambient temperature after 10 minutes. In addition, intake door control system brings on the cost reduction because the flab door can be eliminated. This intake door control system has been adapted to the new developing cars.