• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.1-9
• /
• 2000

To understand the thermal characteristics around the piston ring gap ring gap positions and piston temperatures are measured simultaneously. The locations of piston ring gap are measured by the radio-tracer method and piston temperature are measured by a K-type thermocouple and scissors type linkage system. From these experiments following facts are clarified. Piston temperatures fluctuate according to the piston ring rotation. And the temperature fluctuation is mainly affected by top ring gap position irrelevant to the second ring fop position. If the top ring gap position increases and the temperature of top ring groove shows maximum value when top rin gap position coincide with temperature measuring point. The maximum amplitude of temperature fluctuation which is proportional to the blow by gas rate is around 12-15$^{\circ}C$.

• Design & Manufacturing
• /
• v.11 no.3
• /
• pp.46-50
• /
• 2017

Press processing is one of the best machining methods capable of mass production, satisfying dimensional, shape and quality among the methods of processing a metal plate. Among them, Fine blanking is a method of obtaining a precise cross-section such as machining of the shear surface shape. In this research, Using SCP-1 and SHP-1 materials. The deformation behaviors of the material flow affecting the die height of the shear section in accordance with the position of the V-ring in the Fine blanking were compared and analyzed. Result of interpretation, It was confirmed that the force acts on the position where the material flow direction accurately forms the die roll that the material of SCP-1 is at a position of 1.5 mm and the material of SHP-1 is at 2.0 mm. As a result, it was confirmed that the state of fo1111ing the shear surface by the V-ring was excellent. Using analysis results, In the experiment, the height of the die roll was considered by applying The position of the V-ring was 1.5 mm in SCP-1 and 2.0 mm in SHP-1. As a result of comparing the height of the die rolls, the height values of the die rolls were different from each other, It has been considered that the tendency of the die rolls to coincide with each other. It is considered that the difference of the die roll height is caused by the pressure input of the V-ring. In this study, the deformation behavior of the material(In addition to the position of the V-ring, the flow direction of the material depends on the shape of the V-ring and the Indentation amount) is considered to be an important factor in determining die roll height.

• Journal of the Korean Chemical Society
• /
• v.6 no.2
• /
• pp.162-170
• /
• 1962

The rearrangement reaction of azoxybenzenes into hydroxyazobenzenes in strongly acidic solution has been studied by an U. V. spectrophotometric method and by isolation of the rearranged compound. In all cases under investigation, it appeared that the oxygen atom in the azoxy group migrated to the unsubstituted ring, depending neither on the substituent already present in the other ring, nor on the distance between the oxygen atom and the eligible position; whereas, the position in the open ring, ortho or para, to which the oxygen migrates depends on the substituent already present in the other ring. In all compounds besides ${\alpha}$-and ${\beta}$-4-methyl azoxybenzene, the oxygen atom migrates to the para position. In the case of ${\alpha}$ and ${\beta}$-4-methylazoxybenzene, the oxygen atom migrates to the ortho position of the unsubstituted ring.

• Journal of Sensor Science and Technology
• /
• v.11 no.6
• /
• pp.365-370
• /
• 2002

The jumping ring apparatus described in this study is used to demonstrate and educate the effects of electromagnetic induction. Placing an aluminum ring over the core and switching on AC source causes the ring to jump in the air due to induced currents in the ring producing a magnetic field opposed to that produced in the core. This force is a function of flux density, ac current of ring and levitated height of the ring. Using photo sensor arrays, detect the ring position and represent the position of the ring to analog voltage for an education performance. This paper presents modelling of the jumping ring system and shows how does control signal generate in order to follow desired position.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.820-825
• /
• 2004

The floating ring seal is used in an oxidizer and a fuel pump of the turbo pump unit in the liquid rocket engine to optimize a leakage without rubbing phenomenon. The damper floating ring seal, one of the floating ring seals, is with round hole pattern surfaces. It can reduce the leakage by increased friction factor that obtained from experimental data. In this paper, the leakage test about floating ring seal and damper floating ring seal was conducted. The test result showed the leakage performance of damper floating ring seal was better than the leakage performance of floating ring seal. With the leakage test the lock-up and rotation test about seal was conducted and that position is measured. The relatively large lock-up eccentric ratio was obtained from the test result of damping floating ring seal. The attitude angle of seal increases with increasing of shaft rotation

• Tribology and Lubricants
• /
• v.20 no.4
• /
• pp.183-189
• /
• 2004

The floating ring seal is used in an oxidizer and a fuel pump of the turbo pump unit in the liquid rocket engine to optimize a leakage without rubbing phenomenon. The damper floating ring seal, one of the floating ring seals, is with round hole pattern surfaces. It can reduce the leakage by increased friction factor that obtained from experimental data. In this paper, the leakage test about floating ring seal and damper floating ring seal was conducted. The test result showed the leakage performance of damper floating ring seal was better than the leakage performance of floating ring seal. With the leakage test the lock-up and rotation test about seal was conducted and that position is measured. The relatively large lock-up eccentric ratio was obtained from the test result of damping floating ring seal. The attitude angle of seal increases with increasing of shaft rotation.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.540-542
• /
• 1999

We develop jumping ring system with sensor and control system using dynamic neural networks. Jumping ring, sensor and control system are controlled by 586 PC using Turbo C program. Sensor system is composed of 20 optical sensors and encoder. The control circuits are consisted of thyristor, FET and phase controller. A/D converter and optical sensor acquire real time motion data of the jumping ring system. The information of acquired jumping ring Position is estimated by using dynamic neural networks. Estimated control signals are sent to control circuits and D/A converter to track desired position of the jumping ring system. Experiment results are given to verify that proposed dynamic controller is useful in real jumping ring system.

• Tribology and Lubricants
• /
• v.19 no.6
• /
• pp.349-356
• /
• 2003

A damper floating ring seal with round hole pattern surfaces is suggested for better leakage control. The flat plate test of the round hole pattern surfaces has been performed to yield an empirical friction factor model. The exact predictions of the lock­up position of the damper floating ring, the leakage performance, and the rotordynamic coefficients of the seal are necessary to evaluate the rotordynamic performance of the turbo pump unit. The governing equations including the empirical friction factor model for round hole pattern surfaces are solved by the Fast Fourier Transform method. The lock­up position, leakage flow rate, and rotordynamic coefficients are evaluated according to the geometric parameters of the damper floating ring seal. Theoretical results show that the damper floating ring seals yield less leakage and better rotordynamic stability than the floating ring seal with a smooth surface.

• Archives of Pharmacal Research
• /
• v.16 no.3
• /
• pp.219-226
• /
• 1993

For the analysis of structure relationship of ar-turmerone analogues, the compounds containing the various substituents on the phenyl ring and 1(or 2)-naphthyl group in the place of phenyl of ar-turmerone were prepared and tested their cytotoxicity against HL-60, K-562, and L1210 leukemia cells in vitro. The substituents at para position are methoxy, phenoxy, methyl, trifluoromethyl, fluoro, and chloro. At meta position methoxy, methyl, trifluoromethyl, or chloro groups at ortho position mathoxy or chloro group were introduced. Against HL-60 and K-562 cells, $ED_{50}$ values of the analogues are ranged from 0.8 to $30.0\;\mu{g/ml}$. Againste L1210 cell, these are located more than $20.0\;\mu{g/ml}$. However, 5-carbone-thoxy-2-methyl-6(1-naphthyl)-2-octen-4-one (5n)possesses $ED_{50}$ valuses 0.8, 2.1, $6.5\;\mu{g/ml}$ against HL-60, L1210 cells, respectively. The electronic nature of the substituents on phenyl ring of ar-tumerone dose not affect the biological activity. Therefore the flat structure of aromatic potion of ar-tumerone analogues is the more important factor for their activity rather than its electronic nature. The potentiation of the cytotoxicity with the enlargement of aromatic ring region also supports the importance of the plane structure of this area. The restriction of the single bond rotation between C-6 and aromatic ring through the introduction of substituents at the ortho position of phenyl ring and the increment of size of alkyl group at C-6 position enhances the activity. Therefore the effective conformation should by the one having the orthogonal arrangement between the aromatic ring and the side chain.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.187-192
• /
• 2009

A snap ring is a kind of metal spring with open ends which can be installed into a groove to prevent lateral movement. In this study a nonlinear finite element analysis model is developed to simulate the fastening process of a snap ring connecting the constant velocity joint and the transmission. Insert load, disengage load and breakage are three important issues. They are analyzed using the developed model. The load histories of simulations are similar to those of tests and the differences of maximum load are around 10%. Bending of the entire ring and unfolding of the end section are major contributors of the fastening load. The load variations caused by the angular position of spline tooth are about 50%. Breakage is highly sensitive to the position of a snap ring.