• Applied Chemistry for Engineering
• /
• v.30 no.5
• /
• pp.639-642
• /
• 2019

Hydroxyapatite (HAP) containing hexadecyltrimethylammonium chloride (CTAC) as a cationic surfactant was prepared by a precipitation method. X-ray diffraction (XRD), transmission electron microscopy (TEM) and micropore physisorption analyzer were used for characterizing the crystal phase, morphology and specific surface area of HAP and CTAC-HAP. After thermal treatment, the specific surface area of both pure HAP and CTAC-HAP were reduced. The sharp rod morphology of CTAC-HAP was changed into a round shape with a smaller aspect ratio after the heat treatment. The morphological change by thermal treatment was also observed in pure HAP. Therefore, the morphological change and decrease of the specific surface area suggested that pores from the removal of CTAC during thermal treatment were not retained.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.188-193
• /
• 2006

Synthesis of Boehmite particles were performed through the precipitation of aluminium nitrate ($Al_{3}(NO_{3})_3{\cdot}9H_{2}O$) with ammonia water ($NH_{4}OH$) by changing solution pH, mixing procedure, temperature, and feeding flux. The influence of the synthesis condition, which affected on the pH range of the Boehmite formation, particle morphology and pore property, was investigated. The Boehmite particles were formed in the reaction solution of pH 7.5~9. The particles prepared by P2jet type which maintained the pH uniformly during the precipitation resulted in homogeneous particles and pores because of the constant concentration of the reacted ion in the solution. It was resulted in the improvement of the specific surface area and pore volume of the particle at the same time. With the increasing of temperature and the decreasing of the feeding flux, it was occurred the large specific surface area and pore volume. Also it was presented the fibrillar shaped particles upper $60^{\circ}C$ of the reaction temperature. In this study, the optimal condition of the porous Boehmite was in P2jet type with $90^{\circ}C$ of reaction temperature and 2.5 mL/min of the feeding flux. At this time, the specific surface area, pore volume, and average pore size was $385.46m^2/g$, 1.0252 mL/g, 10 nm, respectively.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.927-933
• /
• 1994

Alumina composite membranes were prepared by chemical vapor deposition (CVD) using aluminum-tri-isopropoxide as a precursor. Porous alumina supports were used in deposition, which were in disk shape with mean pore diameter of 0.1 ${\mu}{\textrm}{m}$ and prepared by slip-coasting process. film deposition morphology on porous support was simulated through depositing alumina film on polycrystalline silicon pattern, and its step coverage observed by SEM showed one deviated from uniform step coverage. N2 permeability through composite membranes and the pressure dependence decreased as the deposition time increased. Initially, the N2 permeability of the top layer was tend to decrease rapidly, and then the degree of decrease in N2 permeability was tend to diminish with deposition time. The N2 permeability increased with heat treatment temperature and the crack was generated in top layer at 100$0^{\circ}C$.

• Korean Journal of Environmental Biology
• /
• v.23 no.4
• /
• pp.323-327
• /
• 2005

Two morphologically different species of Peridinium were frequently observed in natural samples collected monthly from Togyo Reservoir. One was previously identified as P. bipes Stein f. occultatum (Lindem.) Lef. (Ki and Han 2005), the other was remained uncertainly so far. We resolved their identity, based on the morphological observations with scanning electron microscopy. The formula of epithecal plate was recorded with 7 precingular, 3 intercalary and 4 apical plates (4', 3a, 7'). An apical pore was apparently present. The conspicuous morphology of the Peridinium was three spines on the hypothecal plates. The average body length and width were $33.6\;{\mu}m$ with a range of $26\~45{\mu}m$, and 25.7 with a range of $19\~31{\mu}m$, respectively; the cell was, therefore, shown slightly elongated. Based on their morphological characteristics, the causative organism was identified as P. aciculiferum (Lemm.), which was reported for the first time in Korean freshwater.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.92.2-92.2
• /
• 2011

고분자전해질 연료전지 (PEMFC)의 가격 결정 요인 중 막 전극 접합체 (MEA)가 차지하는 비중은 약 45%정도이며, 이것을 구성하는 주요 부품인 기체 확산층 (GDL)은 carbon paper나 carbon cloth 형태가 사용되고 있다. 그렇지만 GDL을 제조하는 공정은 매우 복잡하고, 그 가격이 너무 높은 단점이 있다. 본 연구에서는 카본블랙, 흑연 등의 탄소화합물과 polymer binder를 이용하여 단순화된 공정으로 GDL을 제조하였다. 또한, GDL의 물리적 특성이 전극 성능에 미치는 영향을 분석하기 위하여 표면 morphology, 접촉각 및 표면에너지, 전기전도도, 기체투과도, porosity, pore distrivution 등을 측정하였고, 각각의 GDL 표면에 동량의 Pt 촉매를 도포하여 MEA를 제작한 후 그 성능을 평가하였다.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.49-55
• /
• 2011

Ni nanowires were fabricated using anodic aluminum oxide (AAO) membrane as a template by electrochemical deposition. The nanowires were formed within the walls of AAO template with 200 nm in pore diameter. After researching proper voltage and temperature for electrochemical deposition, the length of Ni nanowires was controlled by deposition time and the supply of electrolyte. The morphology and microstructure of Ni nanowires were investigated by field emission scanning electron microscope (FE-SE), X-ray diffraction (XRD) and transmission electron microscope (TEM).

• Journal of Powder Materials
• /
• v.22 no.3
• /
• pp.216-220
• /
• 2015

Vertically oriented nickel nanowire arrays with a different diameter and length are synthesized in porous anodic aluminium oxide templates by an electrodeposition method. The pore diameters of the templates are adjusted by controlling the anodization conditions and then they are utilized as templates to grow nickel nanowire arrays. The nickel nanowires have the average diameters of approximately 25 and 260 nm and the crystal structure, morphology and microstructure of the nanowires are systematically investigated using XRD, FE-SEM and TEM analysis. The nickel nanowire arrays show a magnetic anisotropy with the easy axis parallel to the nanowires and the coercivity and remanence enhance with decreasing a wire diameter and increasing a wire length.

• Journal of Powder Materials
• /
• v.18 no.2
• /
• pp.129-134
• /
• 2011

Herein, macroporous carbon materials were readily prepared by carbonization of cured body of resorcinol and formaldehyde using poly(methyl methacrylate) colloid microspheres which were employed as the template in the gelation of resorcinol with formaldehyde. The gel in the water was solvent exchanged with methanol and the wet gel was dried. After carbonization of the template-gel composite at $800^{\circ}C$, it was found that pores were left corresponding to the size of the template, yielding carbon materials with a fine porous structure with enlarged surface area and significant porosity. Properties of the carbon foams including the structure, morphology, thermal stability, and porosity were investigated. Finally, it was concluded that the method using polymer colloids as the template provided a facile route to prepare carbon foams.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.181-181
• /
• 2006

We developed a novel method to fabricate a nerve guide conduit (NGC) with the porosity of submicron pore sizes (to prevent fibrous tissue infiltration) and hydrophilicity (for effective oxygen and nutrient permeation) using poly(lactic-co-glycolic acid) (PLGA) and Pluronic F127 by a modified immersion precipitation method designed by our laboratory. It was recognized that the hydrophilized PLGA/F127 (3 wt%) tube can be a good candidate as a NGC from the analyses of its morphology, mechanical strength, hydrophilicity, model nutrient permeability and in vivo nerve regeneration behavior using a rat model.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.167-170
• /
• 1997

For the optimal net shape forging of semi-solid materials (SSM), it is important to predict the deformation for variation of strain rate. It should be necessruy to conduct a formation of stress-strain curve in semi-solid alloys for analysis of the thixoforming process. Particularly, important problem to application of computer aided engineering in SSM processing is to prevent a segregation of liquid component during compression process. The liquid segregation is studied as multistage change of the strain rate and test piece size to prevent the liquid segregation during the compression process. The compression test for semi-solid aluminium alloy with a controlled solid fraction is performed by dynamic material test system with a furnace. Moreover morphology of structure and fraction of pore are investigated through compression test.