• Membrane Journal
• /
• v.8 no.2
• /
• pp.102-108
• /
• 1998

Permeation behavior of the semiconductor rinsing wastewater containing Si particles was examined by ultrafiltration using the polysulfone plate membrane. The permeation flux was gradually decreased with time. It was due to the growth of cake deposited on the membrane surface and the pore plugging by Si particles. Permeation flux of cross flow type was 1.4 times higher than that of the dead end flow type. Nitrogen back flushing which is the removing method of membrane fouling was superior to the water sweeping. With nitrogen back flushing, the decrease of permeation flux due to the fouling was recovered about 85 % to the initial flux in the flat plate membrane system. The rejection rate of Si particles was about 90 % and the size of Si particle in the permeate was about 70 nm.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.666-674
• /
• 2022

The removal efficiencies of nutrients (N and P) and heavy metals (Cu and Ni) by Rhodobacter blasticus and R. blasticus attached to polysulfone carriers, alginate carriers, PVA carriers, and PVA + zeolite carriers in synthetic wastewater were compared. In the comparison of the nutrient removal efficiency based on varying concentrations (100, 200, 500, and 1000 mg/L), R. blasticus + polysulfone carrier treatment showed removal efficiencies of 98.9~99.84% for N and 96.92~99.21% for P. The R. blasticus + alginate carrier treatment showed removal efficiencies of 88.04~97.1% for N and 90.33~97.13% for P. The R. blasticus + PVA carrier treatment showed removal efficiencies of 18.53~44.25% for N and 14.93~43.63% for P. The R. blasticus + PVA + zeolite carrier treatment showed removal efficiencies of 26.65~64.33% for N and 23.44~64.05% for P. In addition, at the minimum inhibitory concentration of heavy metals, R. blasticus (dead cells) + polysulfone carrier treatment showed removal efficiencies of 7.77% for Cu and 12.19% for Ni. Rhodobacter blasticus (dead cells) + alginate carrier treatment showed removal efficiencies of 25.83% for Cu and 31.12% for Ni.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.3
• /
• pp.145-151
• /
• 2015

In order to remove Sr ions and Cs ions from aqueous solution, PS-zeolite beads were prepared by immobilizing zeolite with polysulfone (PS). The prepared PS-zeolite beads were characterized by SEM, XRD, FT-IR, and TGA. The optimum condition to prepare PS-zeolite beads was 1.25 g of PS content and 2 g of zeolite A. The removal efficiencies of Sr and Cs ions by the PS-zeolite beads increased as the solution pH increases and nearly reached a plateau at pH 4. The PS-zeolite beads prepared in this study showed a remarkably high selectivity for Sr ion and Cs ion under the coexistence of ions such as $Na^+$, $K^+$, $Mg^{2+}$, and $Ca^{2+}$. Zeolite particles detached from the PS-zeolite beads were not observed on this experiments, and also the PS-zeolite beads maintained the morphological structure on a SEM image. The removal efficiencies of Sr ions and Cs ions by PS-zeolite beads were maintained over 90% even after five adsorption-desorption cycles. These results implied that the prepared PS-zeolite beads could be an available adsorbent for the adsorption of Sr and Cs ions. These results suggest that the PS-zeolite can potentially be used as an adsorbent in radioactive ions removal for the treatment of industrial wastewater.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.140-145
• /
• 2006

The mort commonly available substrate material is glass in the display fibrication process. However, glass is not desirable due to its heaviness and fragility. Recently, plastics such polysulfone (PSF), polyethesulfone (PES), polycarbonate (PC), polyethylene terephthalate (PET) and cyclic olefin polymers (COP) have been investigated to replace glass as a substrate material for display fibrication. Plastic substrates are advantageous in that they are lightweight, huh impart resistance, flexibility, and ability for roll to roll manufacturing process. But many plastics have poor chemical resistance in organic solvent. The chemica resistance is also lequired because they are exposed to solvents for various chemical treatments din the manufacturing process. So, we have an interest in the chemical modification of PSF to improve chemical resistance. We introduced crosslinkable imide moieties using chloromethylation method for the modification of PSF which could be overcome above shortcomings for display substrate based on plastic film. We prepared the cross-linked polysulfone films which were represented chemical resistance in HeOH, THF, DMSO and NMP. The thermal properties were measured by TGA, DSC and TMA. As the results, we have confirmed to enhance of the thermal property. They had low coefficient of thermal expansion (CTE) which decreased to 15% and had increased $T_g\;from\;180^{\circ}C\;to\;252^{\circ}C$. Cross-linked polysulfone films with imide side-chain had good optical properties and chemical resistance so that they could be used as flexible display substrate.

• Membrane Journal
• /
• v.28 no.6
• /
• pp.379-387
• /
• 2018

This study was conducted to improve the membrane characteristics and performance by increasing hydrophilicity by adding additives to the ultrafiltration polysulfone (PSf) hollow fiber membrane. The mixed matrix membranes (MMMs) were prepared by dispersing 15 nm of fumed silica (FS) in the spinning solution at 0.1, 0.3 and 0.5 wt%. SEM analysis was carried out to confirm the cross-section and surface condition. It was confirmed that mean pore radius of the hollow fiber increased by 4 nm as FS was added. In addition, contact angle measurement was carried out for the hydrophilicity analysis of hollow fiber membranes, and it was confirmed that the hydrophilicity of MMMs were increased by adding of FS. In the case of water permeability, the membrane including FS showed 91~96 LMH and showed 5~11% more increase than PSf membrane. In the antifouling performance test, relative flux reduction ratios of FS mixed hollow fiber membranes were lower than that of PSf membranes, and it was confirmed that increase of hydrophilicity hinders adsorption of hydrophobic BSA on the membrane surface.

• Membrane Journal
• /
• v.31 no.6
• /
• pp.443-455
• /
• 2021

In this study, polyphenylene sulfide (PPS) was used as a support and a separator was manufactured using polysulfone and inorganic additives to manufacture a separator with low membrane resistance for application of an alkali water electrolysis system, and then the effect on the thickness and porosity of the support was analyzed. The PPS felt used as a support was compressed with variables of temperature (100℃, 150℃, 200℃) and pressure (1 ton, 2 tons, 3 tons, 5 tons) to adjust the thickness. A porous separator could be manufactured by preparing a slurry with polysulfone using BaTiO₃ and ZrO₂ which have high hydrophilicity and excellent alkali resistance as inorganic particles and casting the slurry on a compressed PPS felt. Changes in morphology of the separator according to compression conditions were confirmed through an electron scanning microscope (SEM). After that, the porosity was calculated, and the thickness and porosity tended to decrease as the compression conditions increased. Various characteristics were evaluated to confirm whether it could be used as a separator for water electrolysis. As a result of measuring the mechanical strength, it was confirmed that the tensile strength gradually increased as the compression conditions (temperature and pressure) increased. Finally, it was confirmed that the porous separator manufactured through the alkali resistance test has excellent alkali resistance, and through the IV test, it was confirmed that the membranes compressed at 100℃ and 150℃ had a lower voltage and improved performance than the existing uncompressed membrane.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2000.05a
• /
• pp.208-209
• /
• 2000

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2000.04a
• /
• pp.145-149
• /
• 2000

• Proceedings of the Membrane Society of Korea Conference
• /
• 2000.11a
• /
• pp.69-70
• /
• 2000

• 한국전기화학회:학술대회논문집
• /
• 2004.06a
• /
• pp.181-184
• /
• 2004