• Fibers and Polymers
• /
• 제3권1호
• /
• pp.38-42
• /
• 2002

Polypropylene filaments were spun from a mixture of PP chips of two different Melt Flow Index (MFI) (3 MFI and 35 MFI). A significant difference was observed in the melting characteristics of the resultant filaments from either of the individual components as observed from the DSC. The main difference being in the degree of melting achieved at any temperature in the initial stages of the melting range, which was found to be higher in case of the filaments spun from the b]end. These filaments were then thermally bonded using silicon oil bath and heated roller method. Subsequently the bond strength of the filaments was measured on the Instron Tensile Tester using the loop technique. The values of the world strengths obtained from the blend were compared with those made from the individual component. It was found that the bond strength of the bonds obtained from the blended filament at a given temperature was higher than that of the bonds made from the filaments of either of the individual components, which is also suggested by the DSC curves. The difference in the bond strength was found to be as high as 25% in case of the blend with 60:40 composition ratios of the 3 MFI and 35 MFI components respectively.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.264-269
• /
• 2004

The present paper deals with improvement in disperse dyeablility as well as imparting of cationic dyeablility to difficultly dyeable polypropylene by a melt blending technique. Isotactic polypropylene (PP) was blended with fibre grade polybutylene terephthalate (PBT), cationic dyeable polyethylene terephthalate (CDPET) and polystyrene (PS), individually. The resulting binary blends were spun and drawn into fibres at draw ratio 2, 2.5, and 3. The compatibility of blends, structural changes of fibres in terms of X-ray crystallinity, relative crystallinity, sonic modulus, birefringence and thermal stability were examined. The blended fibres were found to be disperse dyeable by the conventional method of high temperature and high pressure dyeing. And this dye ability increased with increase in the level of substitution. PP/CDPET blend also exhibited dyeablility with cationic dyes in addition to that with disperse dyes. The optimum level of blending was predicted keeping in view of tenacity and thermal stability of melt blend fibres. The wash fastness properties of the dyed fibres were found to be of high rate.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2008년도 춘계학술대회
• /
• pp.178-182
• /
• 2008

The bleached red algae fiber(BRAF) showed very similar crystallinity to the cellulose, furthermore, it has higher thermal decomposition temperature than that of the microcrystalline cellulose(MCC). Polypropylene biocomposites reinforced with BRAF have been fabricated with various BRAF contents by compression molding method and their mechanical and thermomechanical properties have been studied. The mechanical strength as tensile, impact and flexural modulus of BRAF/PP biocomposites were gradually improved with increasing the BRAF content, and thermal property which against the thermal expansion was markdly improved, especially. These results are compared with chopped non-woody fibers as Henequen or Kenaf, BRAF was more effective for fabrication of biocomposites reinforced small-sized fibers. The red algae fiber reinforced biocomposites has the applicability such as electronics, biodegradable products and small-structure composites.

• Computers and Concrete
• /
• 제26권2호
• /
• pp.115-125
• /
• 2020

To reduce the damage of concrete in fire, a new type of lightweight cinder aggregate concrete was developed due to the excellent fire resistance of cinder. To further enhance its fire resistance, Polypropylene (PP) Fibers which can enhance the fire resistance of concrete were also used in this type of concrete. However, the bond behavior of this new type of concrete after fire exposure is still unknown. To investigate its bond behavior, 185 specimens were heated up to 22, 200, 400, 600 or 800℃ for 2 h duration respectively, which is followed by subsequent compressive and tensile tests at room temperature. The concrete-rebar bond strength of C30 PP fiber-reinforced cinder concrete was subsequently investigated through pull-out tests after fire exposure. The microstructures of the PP fiber-reinforced cinder concrete and the status of the PP fibre at different temperature were inspected using an advanced scanning electron microscopy, aiming to understand the mechanism of the bonding deterioration under high temperature. The effects of rebar diameter and bond length on the bond strength of PP fiber-reinforced cinder concrete were investigated based on the test results. The bond-slip relation of PP fiber-reinforced cinder concrete after exposure at different temperature was derived based on the test results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권3호
• /
• pp.118-125
• /
• 2013

폴리비닐알코올 섬유와 폴리에틸렌 섬유 등의 합성 섬유는 고연성 섬유보강 시멘트 복합재료를 제조하는데 성공적으로 사용되고 있다. 폴리프로필렌 섬유 역시 복합재료를 제조하는데 사용되고 있지만, 고연성을 구현하는 목적보다는 고온에 노출된 콘크리트의 내화 성능 향상 목적으로 사용되고 있다. 이 연구에서는 폴리프로필렌 섬유로 보강된 시멘트 복합재료의 성능을 향상시키는 방법에 대하여 논하고자 한다. 폴리프로필렌 섬유보강 시멘트 복합재료의 성능을 평가하기 위하여 5가지 배합을 결정하였다. 1종 보통포틀랜드시멘트 (OPC)와 OPC를 다량 치환한 플라이애시를 결합재로 사용하였고 물-결합재 비는 0.23~0.25이다. 또한 부피비로 2%의 폴리프로필렌 섬유가 사용되었으며, 연성을 향상시킬 목적으로 폴리스틸렌 비드가 사용되었다. 슬럼프, 밀도, 압축강도, 1축 인장 실험을 포함한 일련의 실험을 수행하였으며, 실험결과, 파괴역학, 마이크로역학, 통계이론을 이용하여 폴리프로필렌 섬유보강 시멘트 복합재료의 성능을 향상할 수 있는 것으로 나타났다.

• Carbon letters
• /
• 제20권
• /
• pp.39-46
• /
• 2016

In this work, the effects of maleic anhydride (MA) content on mechanical properties of chopped carbon fibers (CFs)-reinforced MA-grafted-polypropylene (MAPP) matrix composites. A direct oxyfluorination on CF surfaces was applied to increase the interfacial strength between the CFs and MAPP matrix. The mechanical properties of the CFs/MAPP composites are likely to be different in terms of MA content. Surface characteristics were observed by scanning electron microscope, Fourier transform infrared spectroscopy, and single fiber contact angle method. The mechanical properties of the composites were also measured by a critical stress intensity factor (K_IC). From the K_IC test results, the K_IC values were increased to a maximum value of 3.4 MPa with the 0.1 % of MA in the PP, and then decreased with higher MA content.

• Structural Engineering and Mechanics
• /
• 제89권4호
• /
• pp.349-362
• /
• 2024

High-performance fiber-reinforced cement composites (HPFRCC) are new materials created and used to repair, strengthen, and improve the performance of different structural parts. When exposed to tensile tension, these materials show acceptable strain-hardening. All of the countries of the globe currently seem to have a need for these building materials. This study aims to create a low-carbon HPFRCC (high ductility) that is made from materials that are readily available locally which has the right mechanical qualities, especially an increase in tensile strain capacity and environmental compatibility. In order to do this, the effects of fiber volume percent (0%, 0.5%, 1%, and 2%), and determining the appropriate level, filler type (limestone powder and silica sand), cement type (ordinary Portland cement, and limestone calcined clay cement or LC3), matrix hardness, and fiber type (ordinary and oxygen plasma treated polypropylene fiber) were explored. Fibers were subjected to oxygen plasma treatment at several powers and periods (50 W and 200 W, 30, 120, and 300 seconds). The influence of the above listed factors on the samples' three-point bending and direct tensile strength test results has been examined. The results showed that replacing ordinary Portland cement (OPC) with limestone calcined clay cement (LC3) in mixtures reduces the compressive strength, and increases the tensile strain capacity of the samples. Furthermore, using oxygen plasma treatment method (power 200 W and time 300 seconds) enhances the bonding of fibers with the matrix surface; thus, the tensile strain capacity of samples increased on average up to 70%.

• 한국건축시공학회지
• /
• 제10권6호
• /
• pp.67-75
• /
• 2010

본 연구는 고강도 콘크리트의 화재시 내화성능 확보를 위하여 주로 사용되는 강섬유(Steel Fiber), 폴리프로필렌(Polypropylene Fiber; 이하PP)와 PP섬유와 강섬유를 하이브리드 섬유를 혼입한 설계기준강도 40MPa의 고강도 콘크리트의 내화성능 및 폭렬 방지 방법을 검토하고, 섬유 혼입 고강도 콘크리트 보의 휨 및 전단보강근이 없는 보의 구조적 특성 연구를 통하여 섬유 혼입 고강도 콘크리트 보의 휨과 전단 저항거동을 파악하였다. 실험결과, 하이브리드 섬유를 보강하면 균열 및 폭렬 발생, 중성화 억제 효과 등을 나타내었다. 부재실험에서는 초기균열제어, 연성과 최대내력 증대의 효과를 나타내었다.

• Composites Research
• /
• 제23권3호
• /
• pp.50-57
• /
• 2010

섬유 보강 시멘트계 복합재료의 성능 예측 및 평가에 있어서 중요한 영향을 미치는 섬유 분포 특성을 정량적으로 평가하기 위해서는 복합재료의 단면 이미지에서 섬유를 정확히 검출하여야 한다. 이 논문은 형광원리를 이용하여 합성섬유를 매트릭스로부터 개별적으로 검출하기 위한 기초 연구로써 섬유 보강 시멘트계 복합재료 중의 하나인 ECC에 일반적으로 사용되는 PVA 섬유, PET 섬유, PE 섬유, 그리고 PP 섬유의 형광특성을 분석하였다. 또한 하이브리드 된 경우 합성섬유들 간의 상대 형광 광도값의 차이를 비교하여 종류별로 구분하기 위한 최적의 파장대를 선정하였으며, 그 파장대에서 두 분류대상을 구별할 수 있는 최적의 경계값을 통계적 방법을 이용하여 산출하였다. 또한 형광 현미경을 이용하여 각 섬유를 촬영하여 상대적인 밝기값을 비교하였다.

• Macromolecular Research
• /
• 제16권1호
• /
• pp.21-30
• /
• 2008

Based on the sheath-core bicomponent composite fibers with modified polystyrene (PS) and the modified polypropylene (PP), composite fibers obtained were further cross-linked and sulphonated with chlorosulphonic acid to produce strong acidic cation ion exchange fibers. The structures of the fibers obtained were characterized using Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC) etc. The optimal technology of the fibers obtained is discussed. The static absorption capacity of the sheath-core bicomponent composite cation exchange fibers for $Zn^{2+}$, $Cu^{2+}$ was determined. The absorption kinetics and major factors affecting the absorption capacities of $Zn^{2+}$, $Cu^{2+}$ were studied, and its chemical stability and regenerating properties were probed. The results suggest that cation exchange fibers with better mechanical properties and higher exchange capability were obtained. Moreover, this type of ion exchange fiber has good absorption properties and working stability to various metal ions. Hence, they have higher practicability.