• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• Advances in concrete construction
• /
• v.10 no.1
• /
• pp.1-11
• /
• 2020

This study intends to produce an ultra-high performance fibre reinforced concrete (UHPFRC) made with hybrid fibres (i.e., steel and polypropylene). Compressive and tensile strength characteristics of the hybrid fibres UHPFRC are considered. A total of 14 fibre-reinforced composites (FRCs) with different fibre contents or types of fibres were prepared and tested in order to determine a suitable hybrid fibre combination. The compressive and tensile strengths of each concrete at 7 days were determined. The results showed that a hybrid mix of micro-polypropylene and steel fibres exhibited good compromising performances and is the ideal reinforcement mixture in a strong, cost-effective UHPFRC. In addition, maximum compressive strength of 167 MPa was achieved for UHPFRC using 1.5% steel fibres blended with 0.5% macro-polypropylene fibres.

• Journal of the Korean Chemical Society
• /
• v.23 no.6
• /
• pp.412-416
• /
• 1979

Although isotactic polypropylene gives an excellent fiber having high tenacity, abrasion resistance and chemical stability, it has not been widely used as a fabric for chlothing because of its poor dyeability. A number of methods for improvement of its dyeability have been proposed, but they were too complicated and/or gave damage its original excellent properties of polypropylene. We now wish to report the synthesis of a new reactive dye for polypropylene fiber by means of carbenic process. A reactive dye was synthesized from azo disperse dye having an aldehyde group and tosylhydrazine. By using this synthesized reactive dye, polypropylene fiber was dyed to thick and fast color.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.665-670
• /
• 2005

Nanocomposites of polypropylene with organically modified clays were compounded on a twin-screw extruder by two-step melt compounding of three components, i.e., polypropylene, maleic anhydride grafted polypropylene (PP-g-MA), and organically modified clay. The effect of PP-g-MA compatibilizers, including PH-200, Epolene-43, Polybond-3002, Polybond-3200, with a wide range of maleic anhydride (MA) content and molecular weight was examined. Morphologies of nanocomposites and their mechanical properties such as stiffness, strength, and impact resistance were investigated. X-ray diffraction patterns showed that the dispersion morphology of clay particles seemed to be determined in the first compounding step and the further dispersion of clays didn't occur in the second compounding step. As the ratio of PP-g-MA to clay increased, the clay particles were dispersed more uniformly in the matrix resin. As the dispersibility of clays was enhanced, the reinforcement effect of the clays increased, however impact resistance decreased.

• Environmental Engineering Research
• /
• v.11 no.5
• /
• pp.257-265
• /
• 2006

The purpose of research is to mix the fly ash from municipal solid waste incinerator in the recycled Polypropylene and to recycle. The specimen was produced by mixing 20 wt.% of MSWI fly ash at maximum in the recycled Polypropylene and the particle size analyzer, DSC, TGA, SEM and UTM instruments were used to analyze the physical chemical properties of the specimen. As a result of measurement, the average particle size of MSWI fly ash was $18.08\;{\mu}m$. In TGA analysis, the temperature of specimen S-5 at 50% of weight decrease was risen by $7^{\circ}C$ higher than specimen S-1. In UTM measurement, specimen S-2 showed the maximum strength for tensile strength and specimen S-3 showed the maximum strength for flexural strength. But, impact strength was decreased according to the increasing proportion of MSWI fly ash. In conclusion, when the proper amount of MSWI fly ash was added to the recycled Polypropylene, thermal endurance, tensile strength and flexural strength could be increased, but impact strength was decreased.

• Structural Engineering and Mechanics
• /
• v.62 no.3
• /
• pp.373-380
• /
• 2017

Concrete structures are often subjected to long-term static and short-term dynamic loads. Due to a relatively low tensile strength and energy dissipating characteristics, the impact resistance of concrete is considered poor. This study investigates the feasibility of using polypropylene fibers to improve the impact resistance of reinforced concrete slabs. Fourteen polypropylene fiber reinforced concrete slabs were fabricated and tested using a drop weight test. The effects of slab thickness, fiber volume fractions, and impact energy on the dynamic behaviors were evaluated mainly in terms of impact resistant, crack patterns, and failure modes. The post impact induced strains versus time responses were obtained for all slabs. The results showed that adding the polypropylene fiber at a dosage of 0.90% by volume of concrete leads to significant improvement in the overall structural behavior of the slabs and their resistance to impact loading. Interestingly, the enhancement in the behavior of the slabs using a higher fiber dosage of 1.2% was not as good as achieved with 0.90%.

• Advances in concrete construction
• /
• v.10 no.4
• /
• pp.319-332
• /
• 2020

The impacts of reinforcing concrete matrix with steel fibers, polypropylene fibers and recycled plastic fibers using different volume fractions of 0.15%, 0.5%, 1.5% and 2.5% on the compressive and tensile characteristics are experimentally investigated in the current research. Also, flexural behavior of plain concrete (PC) beams, shear performance of reinforced concrete (RC) beams and compressive characteristics of both PC and RC columns reinforced with recycled plastic fibers were studied. The experimental results showed that the steel fibers improved the splitting tensile strength of concrete higher than both the polypropylene fibers and recycled plastic fibers. The end-hooked steel fibers had a positive effect on the compressive strength of concrete while, the polypropylene fibers, the recycled plastic fibers and the rounded steel fibers had a negative impact. Compressive strength of end-hooked steel fiber specimen with volume fraction of 2.5% exhibited the highest value among all tested samples of 32.48 MPa, 21.83% higher than the control specimen. The ultimate load, stiffness, ductility and failure patterns of PC and RC beams in addition to PC and RC columns strengthened with recycled plastic fibers enhanced remarkably compared to non-strengthened elements. The maximum ultimate load and stiffness of RC column reinforced with recycled plastic fibers with 1.5% volume fraction improved by 21 and 15%, respectively compared to non-reinforced RC column.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.4
• /
• pp.73-81
• /
• 2010

The cemented sand and gravel (CSG) method is a construction technique that adds cement and water to rock-like materials, such as rivered gravel or excavation muck which can be obtained easily at areas adjacent to dam sites. This study was performed to evaluate the compaction and compressive strength properties of stress-strain, elastic modulus and fracture mode CSG materials reinforced polypropylene fiber. Polypropylene fiber widely used for concrete reinforcement is randomly distributed into cemented sand. The two types of polypropylene fiber (monofillament and fibrillated fiber) were used and fiber fraction ratio was 0, 0.2 %, 0.4 %, 0.6 % and 0.8 % by the weight of total dry soil. The effect of fiber fraction ratio and fiber shape on compaction and compressive strength were investigated. The optimum moisture contents (OMC) of CSG material increased as fiber fraction increased and the dry density of CSG material decreased as fiber fraction. Also, the maximum increase in compressive strength was obtained at 0.4 % content of monofillament and fibrillated fiber. CSG material behaviour was controlled not only by fiber fraction but also fiber distribution, fiber shape and fiber type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.367-371
• /
• 2007

Nanocomposites prepared by PP(Polypropylene) based compatibilizers modified with GMA(Glycidyl methacrylate) and HEMA(Hydroxyethyl methacrylate) were used to investigate the clay dispersion and mechanical properties of them. XRD patterns showed the improvement of dispersion through clay intercalation according to the compatibilizers and comonomer. GMA modified polypropylene gave the best mechanical properties of the nanocomposite with respect to the balance of Flexural modulus (FM) and Notched izod impact strength(IS). Compatibilizers with comonoer commonly have higher grafting yield and lower melt flow rate than those of comonomer free. And they enhanced the clay dispersion and mechanical properties of nanocomposites. Optimum ratio of monomer to comonomer for nanocomposites having better mechanical properties is about 1 to 1 ratio.

• Journal of Adhesion and Interface
• /
• v.6 no.2
• /
• pp.1-5
• /
• 2005

Single crystals of metallocene-catalyzed isotactic polypropylene (iPP) and/or syndiotactic PP (sPP) were prepared and preliminarily characterized. The crystallization was performed utilizing 0.1 % by weight concentrations of each PP in o-xylene in the range of temperature of $40{\sim}90^{\circ}C$. Following the XRD patterns, samples were ${\alpha}$-iPP and antichiral Cell III of sPP. The XRD pattern of iPP shows three ${\alpha}$-form peaks due to the (110), (040), (130) planes at $2{\theta}=14.2^{\circ}$, $17^{\circ}$, $18.8^{\circ}$, respectively. The XRD pattern of sPP is characterized by the presence of the (020) reflection at $16^{\circ}$. The melting point ($123^{\circ}C$ and $148^{\circ}C$, respectively) of the metallocene catalyzed iPP and sPP were generally lower than that of conventional PP ($160{\sim}170^{\circ}C$) due to the misinsertion of the monomer. When metallocene-catalyzed iPP samples were crystallized isothermally from solution grown at a lower temperature, lozenge shape single crystals were observed by transmission electron microscopy (TEM).