• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.19-24
• /
• 1962

In the emulsion polymerization of vinyl acetate with Triton-X(Alkyl-aryl-polyether alcohol) and polyvinyl alcohol as emulsifier, some relations between the conditions of polymerization and the polymerization rate, polymerization degree and stability of the emulsion are studied and discussed.

• Composites Research
• /
• v.26 no.3
• /
• pp.182-188
• /
• 2013

The purpose of this study was to measure the volumetric polymerization shrinkage kinetics and stress of a silorane-based dental restorative composite and compare it with those of conventional methacrylate-based dental composites. Two methacrylate-based composites (Z250, Z350 flowable) and one silorane-based composite (P90) were investigated. The volumetric polymerization shrinkage of the composites during light curing was measured using a laboratory-made volume shrinkage measurement instrument based on the Archimedes' principle, and the polymerization stress was also determined with the strain gage method. The shrinkage of silorane-based composites (P90) was the lowest, and that of Z350 flowable was the highest. Peak polymerization shrinkage rate was the lowest in P90 and the highest in Z350 flowable. The time to reach peak shrinkage rate of P90 was longer than those of the methacrylate-based composites. The polymerization shrinkage stress of P90 was lower than those of the methacrylate-based composites.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.233-237
• /
• 1991

In the study, samples were made on the electrode in internal glass bell jar by the radio frequency discharge polymerization. The polymerization rate of samples was observed as a function of r.f. discharge power. The characteristics of polymers obtained from TMDSO and HMDSO were analyzed by FT-IR and TGA, and their electrical properties were examined on insulation resistivity, breakdown voltage, dielectric constant, and tan ${\delta}$. (1) There was no difference between PPTMDSO and PPHMDSO in a polymerization rate and thermal and electrical properties. (2) The growing rates of thin film with discharge powers were from $0.42{\mu}/h$ to $1.2{\mu}m/h$. (3) According to IR spectra analysis, discharge power did not effect polymer structure due to polyermization mechanism and effected only polymerization rate. (4) PPTMDSO and PPHMDSO were thermally resistive polymers which did not decompose to $300^{\circ}C$.

• Polymer(Korea)
• /
• v.34 no.4
• /
• pp.341-345
• /
• 2010

Effects of modification of silver nanoparticles on the polymerization rate and morphology of poly(methyl methacrylate)(PMMA)/silver microspheres prepared by suspension polymerization of MMA were investigated. The silver nanoparticles and their surface hydrophilicity played an important role in the polymerization rate and the morphology of poly(methyl methacrylate) (PMMA)/silver microspheres. The polymerization rate increased slightly with modified silver nanoparticles. PMMA/silver microspheres with conversion up to 85% were obtained in spite of the low polymerization temperature. Due to the change of hydrophilicity of silver nanoparticles, different appearances of the microspheres having golf ball-like convex surfaces or concave surfaces were observed. As the hydrophilicity of silver was decreased, stable nanocomposites were prepared.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.50-55
• /
• 2006

When the monodisperse polystyrene(PS)/HDDA polymer particles were synthesized via one-step polymerization using polystyrene seed particles by dispersion polymerization, the effects of 1) the molecular weight of seed polymer particles, 2) the ratio of the absorbed HDDA to the seed polymer particles (swelling ratio) and 3) seeded polymerization rate on the surface morphology of PS/HDDA polymer particles were investigated. It was observed that the creation of the crater shaped defect on the surface of PS/HDDA polymer particles was irrespective of the molecular weight of seed polymer ant swelling ratio. But its surface morphology could be controlled by the change of the seeded polymerization rate.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.739-744
• /
• 1996

Lanthanide diphthalocyanines have interesting properties on electrochemical and chemical redox reactions. It is however, difficult to use because of thier short device life. Plasma-polymerization attends to improvement thier device life. Yb-diphthalocyanine ($YbPc_2$) polymer film was deposited in a parallel plate electrodes-type RF plasma reactor. $YbPc_2$ was sublimed into the argon plasma, and polymer film was obtained on a substrate. Radio frequency was constant of 13.56MHz. Pressure of argon gas, sublimation rate of $YbPc_2$ and RF power were variable parameters depending on film quality. Surface of polymer films include a lot of sub-micron order lumps. It was indicated that size of lumps depends on polymerization degree controled by parameters. Size of lumps and polymerization degree are increased with RF power. However, by the high RF power over 40W, polymerization degree is decreased with RF power and surface of film is rough. In condition of RF power is high, polymerization will compete with etching of film. We obtained good films for electrochromic display with RF power of 20W, argon gas pressure of 8.0 Pa and sublimationrate of $1.2 \times 10$ mol/min, and good films for gas sensor with RF power of 30W, argon gas pressure of 10.6Pa and sublimation rate of $1.2 \times 10$ mol/min.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.390-394
• /
• 2011

Effects of silver nanoparticles on the polymerization rate and morphology of poly(vinyl acetate) (PVAc)/silver microspheres prepared by suspension polymerization of VAc were investigated. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction and atomic absorption spectrometry were used to characterize the morphology and properties of the PVAc/silver microspheres. Due to the change of hydrophilicity of silver nanoparticles, appearance of the microspheres having golf ball-like convave surfaces was observed. Under controlled concentration of surfactant, PVAc/silver microspheres with various hollow structures were synthesized. In the case of silver nanoparticles modified by surfactant, the polymerization rate increased slightly. PVAc/silver microspheres with a conversion up to 80% were prepared via suspension polymerization.

• Elastomers and Composites
• /
• v.50 no.4
• /
• pp.286-291
• /
• 2015

Polyvinylacetate (PVAc) was prepared using thermal initiation and redox initiation via emulsion polymerization at $80^{\circ}C$. The polymerization conditions had a significant effect on the properties of the synthesized PVAc. When hydrogen peroxide and tartaric acid as the initiator for redox polymerization were used, the synthesized PVAc had a low molecular weight. In comparison with thermal polymerization, smaller PVAc particles were formed during the redox polymerization due to relatively faster polymerization rate, which in turn resulted in improved adhesion property. It is considered that the rapid generation of smaller particles induces the formation of a large surface area.

• Nuclear Engineering and Technology
• /
• v.4 no.1
• /
• pp.23-30
• /
• 1972

A study on the preparation of wood-plastic combinations by gamma-ray induced polymerization is carried out. In monomer impregnation, the rates and amounts are determined for various woods. The polymerization rates of various monomers and monomer mixtures impregnated mainly domestic woods are studied varying the total gamma-dose and gamma-dose rates. The obtained data indicate that; 1) in impregnation of monomer, populus deltoides is the fastest in rate, and the most impregnated in amount 2) the general trends of polymerization of monomers ill woods is in the order of vinyl acetate--methyl metacrylate--styrene, ranging from 3 to 15 Mard of total does in rate of 4$\times$10$^4$rad/hr., thus vinyl acetate or methyl metacrylate is suitable monomer in view of polymerization rate, 3) the successful woods in combination with monomer are pinus rigida and pinus densiflora in view of polymerization rate, 4) the monomers in woods are more easily polymerized under the conditions of moderately lower does rate, 2.1$\times$10$^4$rad/hr.

• Membrane Journal
• /
• v.27 no.6
• /
• pp.506-510
• /
• 2017

The interfacial polymerization method has been applied to various fields as a reaction in which reactive monomers dissolved in two immiscible solutions cause polymerization at the interface. In the case of water treatment membranes, m-phenylene diamine and trimesoyl chloride are used as reactants. The performance of the membrane is affected by various polymerization factors. In this study, we investigated how the spreading rate of the organic solution influences the surface and structure of the membrane. Spreading rate of organic solutions was adjusted to 7.6 and 25 mm/sec. The solution volume of the organic phase was adjusted to 1~3 drops. The observed results showed that cracks were not found in the polyamide membrane when dropping at a drop of 7.6 mm/sec and dropping two drops at 25 mm/sec. On the other hand, cracks occurred in all cases. Therefore, the spreading rate of the initial organic solvent is expected to greatly affect the performance of the polyamide membrane.