• Journal of Adhesion and Interface
• /
• v.2 no.1
• /
• pp.1-8
• /
• 2001

In this study, wasted stone powders (WSP) obtained from sludge and Wasted Tire Chips (WTC) as fillers have been used to formulate polymer hybrid composites based on Unsaturated Polyester (UPE) resin. To further enhance not only the interfacial bond between the inorganic filler and the polymer matrix, but also the filler dispersion by wetting the particulate surfaces to uniformly spread the resin during the mixing, silane coupling agent[${\gamma}$-methacryloxy propyl trimethoxy silane (${\gamma}$-MPS)] was used. The influences of organic recycled fillers contents and the concentrations of coupling agent in polymer hybrid composite formulations have been investigated from a mechanical and microstructural point o view through Mercury Porosimeter and SEM.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.524-530
• /
• 2004

Polystyrene particles (PS) with poly(ethylene glycol) units on surface were formed by an emulsifier-free emulsion polymerization using styrene, poly(ethylene glycol) methacrylate (PEG-MMA) or poly(ethylene glycol) dimethacrylate (PEG-diMMA) at pH 7, and followed by freeze-drying to give the corresponding powders. The structures of PS particles were confirmed by FT-IR spectroscopy, and the particle size and distribution the PS particle were observed by scanning electron microscopy and particle analyzer. Monodisperse polymer particles were obtained at a concentration of PEG-MMA 2∼5 mol% or PEG-diMMA 1 mol% relative to styrene. The highest zeta potential of polymer surface was measured to be 183 mV at a polymer of PEG-MMA 5 mol%, which was measured in dielectric medium by means of ELS-8000 dynamic light scattering.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.240-245
• /
• 2001

The effect of additives on the orientation of magnetic Sr-ferrite powders has been studied during powder injection molding under applied magnetic field for fabricating multi-pole anisotropic sintered Sr-ferrite magnets. The orientation of the Sr-ferrite powders depends sensitively on the fluidity of powder-binder mixture, related to the binder additives and the injection molding temperature, and the magnetic field intensity. The orientation of Sr-ferrite powders is good for the compacts with stearic acid added in the binder system of paraffin wax/carnauba wax/HDPE, but it is poor for the compacts with silane coupling agent added. The orientation of Sr-ferrites higher than 80% is achieved at the following useful conditions; apparent viscosity lower than 2500 poise in 1000 sec$^{-1}$ shear rate and applied magnetic field higher than 4 kOe.

• Macromolecular Research
• /
• v.8 no.5
• /
• pp.231-237
• /
• 2000

The polymerization of 3-ethynylphenol, phenylacetylene having hydroxy functionality, was carried out by tungsten and molybdenum-based transition metal catalysts. The polymerization proceeded to give a moderate yield of polymer. The effects on the mole ratio of monomer to catalyst (M/C), initial monomer concentration ((Mb), and the polymerization temperature for the polymerization of 3-ethynylphenol were investigated. The catalytic activity of W-based catalysts was found to be greater than that of Mo-based catalysts. The resulting polymers were brown or black powders and mostly insoluble in organic solvents. Structural analysis of the polymer by instrumental methods revealed the conjugated polymer backbone structure carrying hydroxyphenyl moieties. Thermal and morphological properties of the resulting poly(3-ethynylphenol) were also discussed.

• Journal of the Korean Ceramic Society
• /
• v.23 no.5
• /
• pp.41-46
• /
• 1986

공침법에 의하여 얻어진 고순도 극미립자인 $BaTiO_3$ 분말의 분산거동을 조사하였다 분산매로는 수용매와 비수용매인 methyl ethyl ketone(MEK)과 ethanol (ETOH)을 이용하였다 Suspension 에서의 입자의 분산상태는 pH 변화와 MEK, ETOH의 몰 비를 조절하여 각각의 suspensions에 polymer(polyvinyl butyral)를 첨가시켜 변화하였으며 그 거동은 유동학적 성질 침강 거동 electrokinetic 성질을 측정함으로써 파악되었다 비 수용매의 몰 비가 3:1 MEK/ETOH-$BaTiO_3$에서 polymer를 0.5~1% 첨가시켰을 때 입자의 분산이 가장 잘 이루어졌다.

• Journal of Powder Materials
• /
• v.18 no.2
• /
• pp.181-187
• /
• 2011

PVDF was used as a polymeric matrix material in this work. Nickel powders with average particles size of 200 nm or 72 nm were used as fillers. PVDF/metal submicro- and nanocomposites were prepared by means of a mixing in twin screw extruder and planetary ball mill, respectively. All samples were prepared by hot pressing method. Their electrical, thermal and morphological properties were examined by dielectric spectroscopy, DSC, FTIR, XRD, optical microscopy and scanning electron microscopy. It was found that all properties of composites were strongly modified depending on the content of metal powders and filler particles size. Particularly, specific volume resistivity of PVDF/Ni composite with 0.2 wt.% of Ni was increased by factor of 1.5~4.

• Journal of Powder Materials
• /
• v.12 no.4 s.51
• /
• pp.249-254
• /
• 2005

Titanium dioxide was prepared by Polymer Complex Solution Method(PCSM) according to the mole ratio of Titanium (IV) isopropoxide(TTIP)/solvent and polymer(Poly Ethylene Glycol). Polymer electrolytes were usually made by dispersing preproduced ceramic nanoparticles in a polymer matrix. Using this method, pure and nano-sized $TiO_2$ powder was synthesized through a simple procedure and polymer entrapment route. At the optimum amount of the polymer, the titanium ions are dispersed in solution and a homogeneous polymeric network is formed. The maximum intensity of anatase phase of $TiO_2$ was achieved by calcining at $500^{\circ}C$ for 2h. The synthesized $TiO_2$ powders were nano-sized and the average size was about 50nm. Anatase/Rutile ratio of the synthesized $TiO_2$ was 70%/30%.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.94-101
• /
• 2011

The conventional radiation barriers may show some disadvantages such as heavy weight and possibility of poisoning human bodies because they are composed of lead plates or resin plates containing large amounts of lead powders. Another disadvantage may be direct penetration of radiation through small pin holes. In this article, technologies of multi-layered polymer barriers against radiation, which has been extensively focused recently, will be introduced. A new concept of radiation protection as well as improving endurance with employing nano-layered inorganic particles is introduced.

• Journal of the Korean Magnetics Society
• /
• v.22 no.6
• /
• pp.216-220
• /
• 2012

Magnetic properties of composite materials consisting of polymer filled with ferromagnetic powders (MnZn ferrite, Fe-Si alloy) were investigated in this study. The volume fraction of magnetic powders as fillers was varied from 70 % to 95 %. This paper presents the fabrication method of polymer magnetic composites in an effort to produce the 0-3 types of MnZn ferrite and FeSi as fillers with a proper complex permeability through the optimization of some experimental parameters. The polymer matrix composites were prepared by mixing the crushed ferrites and flaky FeSi powders homogenously with low-density resins (EPDM, epoxy). The relationships among the manufacturing technology of these materials, their filler volume fraction, as well as their complex permeability were measured and analyzed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1227-1228
• /
• 2006

The electrochemical properties of novel metal powders were investigated for the electrode materias of polymer electrolyte memebrane electrolysis. Two types of Pt black and $IrO_2$ powder electrodes were hot-pressed on the polymer electrolyte membrane to form membrane electrode assembly. The galvanodynamic polarization methode was used to characterize the electrochemical properties of both electrodes. From the experimental results, we concluded that the $IrO_2$ powder electrode exhibits better electrochemical performance than Pt black as cathode material for the electrolysis.