• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.951-954
• /
• 2001

We investigated the aligning capabilities for nematic liquid crystal (NLC) using a in-situ photodimerization method on various photopolymer surfaces. High Pretilt angle of the NLC can be measured by obliquely polarized UV exposure of 30$^{\circ}$on a photo-crosslinkable polyimide (PI) based polymer surface for 3 min. The pretilt angle of the NLC generated on the photopolymer surface using the in-situ photodimerization method was higher than that of a blending photopolymers (PI and cinnamate materials).

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.816-818
• /
• 1998

In this paper Polyimide(PI) thin film are fabricated by vapor deposition polymerization(VDP) of dry process which are easy to control the film's thickness and hard to pollute due to volatile solvent. The FT-IR spectrum show that PAA thin films fabricated by VDP are changed to PI thin film by thermal curing. From AFM(Atomic Force Microscopy) experimental as the higher curing temperature. the thin film thickness decreases and roughness decresse.

• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.1
• /
• pp.51-54
• /
• 2002

Polymer EL devices of glass/ITO/PI/MEH-PPV/Al structure were fabricated using spin coating and the Ionized Cluster Beam deposition technique. PMDA-ODA type thin polyimide films which can be used as a impurity blocking layer of EL device were deposited by ICB. According to our previous results, the packing densities of polyimide films were subject to change and depend on their deposition condition. By inserting a Pl layer with various thickness and packing density, I-V characteristics and life time of the devices were investigated to determine the role of a interlayer. The blocking of impurity diffusion from ITO to luminescent layer were confirmed by XPS.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05a
• /
• pp.6-6
• /
• 1992

Ionized cluster beam deposition (ICBD) technique has been employed to fabricate high-purity crystalline polyimide (PI) film. The pyromellitic dianhydride (PMDA) and oxydianiline (ODA) were deposited using dual ICB sources, Fourier trans forminfraredspectroscopy (FT-IR), X-ray photoemission spectroscopy (XPS), and Transmission electron microscopy (TEM)study show that the bulk and surface chemical properties and the crystalline structure are very sensitive to the ICBD conditions such as cluster ion acceleration voltage and ionization voltage, At optimum ICBD conditions, the PI films have a maximum imidization, negligible impurities(∼1% isoimide), and a good crystalline structure probably due to the high surface migration energy and surface cleaning effect. These characteristics are superior to those of films deposited by other techniques such as colvent cast, vapowr deposition, or sputtering techniques.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1144-1148
• /
• 2006

We have investigated liquid crystal (LC) aligning capabilities and electro-optical (EO) characteristics of transparent electrodes as Al-doped ZnO (AZO) substituting indium tin oxide (ITO). The experiment results show that a uniform vertical LC alignment on AZO electrodes based on a rubbed polyimide (PI) surface were achieved. A high pretilt angle of about $88^{\circ}$ was obtained. EO performances of the VA cell on rubbed PI surfaces with AZO electrodes are almost the same as that of the VA cell with ITO electrodes. These results appeared that AZO electrodes as transparent electrodes of LCDs could substitute ITO electrodes.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.414-416
• /
• 1995

We have studied the effect of the mesogenic core of nematic liquid crystals (NLCs) for polar (out-of-plane tilt) anchoring strength on rubbed polyimide (PI) films. The order of polar anchoring strength for NLCs on rubbed PI films is 5CB > PCH5 > CCH5. This order is the same for all rubbing strengths investigated. From these results, we suggest that the polar anchoring strength strongly depends on the polarizability of the NLCs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.871-875
• /
• 2000

Effects of liquid crystal (LC) alignment using a in-situ photoalignment method by polarized UV exposure on a polyimide (PI) surface with medium side chain were studied. The generated pretilt angle in nematic(N) LC using a in-situ photoalignment method was smaller than that of a conventional photoalignment method for short UV exposure time. Also, the pretilt angle of NLC using a in-situ photoalignment method increases with increasing UV exposure time on the PI surfaces. Finally, the pretilt angle of NLC can be improved by annealing treatment.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2004.05a
• /
• pp.101-107
• /
• 2004

각종 전자기기의 소형화, 고성능화 요구에 따라 회로 또는 기판의 고집적화에 따른 대안으로 도입된 COF(Chip On Film)공정에서 PI(polyimide)/buffer layer/Cu의 접착력 개선을 목적으로 본 연구가 진행 되었다. 그리고 buffer layer로써 Cr을 증착 할 때 부착력의 개선을 목적으로 개질처리를 할 때는 RF plasma장비를 사용하였다. 실험 변수로는 peel strength에 대한 buffer layer의 종류와 증착시간, 표면 개질처리시 $O_2$/Ar비이다. Buffer layer의 종류에 따른 접착력은 Cr보다 Ni이 우수하였고 peel strength와 Cu THK는 같은 buffer layer의 증착 structure에서 비례 관계를 나타냈으며, Cr의 증착 시간과 Cu의 증착 시간을 변수로 peel strength test한 값은 Cr증착시간이 30초, Cu증착시간이 20분일때 40g/mm로 최적의 접착력이 나타났다. 증착전 PI의 개질 처리시 $O_2$/Ar 유량비에 따른 peel strength값은 $O_2$/Ar유량비가 증가 할수록 향상되었으며, 2/5에서 최고값인 58g/mm가 나타났다. 그 이상에서는 오히려 감소하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.198-201
• /
• 1997

We investigated the generation of pretilt angle for nematic liquid crystal (NLC) in a cell with slanted non-polarized ultraviolet (UV) light irradiation on mixtured polyimide (PI) surfaces. It was found that the monodomain alignment of NLC is obtained in a cell with an angle of incidence of 75∼85 degrees on PI surface. We consider that the monodomain alignment of NLC is attributed to anisotropic dispersion force effect due to photo-depolymerization of polymer on Pl surfaces. We successfully observed that the pretilt angle of NLC is generated above 5 degree with an angle of incidence of 75∼85 degree. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecules and the Polymer surfaces.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.950-953
• /
• 2000

Aligning capabilities of nematic liquid crystal(NLC) using an in-situ photo-alignment method with obliquely polarized UV exposure on a polyimide (PI) surface for homeotropic alignment were studied. The high angle for NLC can be measured by obliquely UV exposure of 30°on the PI surface for 10∼20 min. The pretilt angle of NLC generated using the in-situ photo-alignment was higher than that of a conventional photo-alignment method. Finally, we suggest that the control of pretilt angle in NLC with obliquely polarized UV exposure during imidization of the polymer for homeotropic alignment is promising method to generate high pretilt angle.