• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.146-150
• /
• 2005

In this paper, friction of air-jet textured yams is investigated. Using a friction measuring apparatus fabricated inhouse, dynamic friction forces of the yams under yarn-to-metal (YM) and yam-to-yam (YY) rubbing modes are measured. The influence of processing variables of air-jet texturing viz., overfeed, air pressure, dry/wet texturing and normal/core-and-effect texturing on dynamic friction is analysed. The results indicate that friction force increases with increasing rubbing speeds and yam input tension. YM dynamic friction decreases initially and then starts to increase at higher overfeeds. YY dynamic friction increases with increasing overfeed. YM dynamic friction decreases with an increase in air pressure while an opposite trend is observed for YY friction. Wet textured yams have higher friction than dry textured yams. Core wetted coreand-effect textured yams have higher friction than normal textured yams.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.2
• /
• pp.58-67
• /
• 2003

Over the last decade fiber-reinforced polymer (FRP) reinforcement consisting of glass, carbon, or aramid fibers embedded in a resin such as vinyl ester, epoxy, or polyester has emerged as one of the most promising and affordable solutions to the corrosion problems of steel reinforcement in structural concrete. But reinforcing rebar for concrete made of FRP rebar has linear elastic behavior up to tensile failure. For safety a certain plastic strain and an elongation greater than 3% at maximum load is usually required for steel reinforcement in concrete structures. The same should be required for FRP rebar. Thus, the main object of this study was to develop new type of hybrid FRP rebar Also, this study was evaluated to the mechanical properties of Hybrid FRP rebar. The Manufacture of the hybrid FRP rebar was achieved by pultrusion, and braiding and filament winding techniques. Tensile and interlaminar shear test results of Hybrid FRP rebar can provide its excellent tensile strength-strain behavior and interlaminar stress-strain behavior.

• Elastomers and Composites
• /
• v.34 no.4
• /
• pp.299-314
• /
• 1999

Bonding metal and textile components to rubber has always posed a problem. In this paper, an attempt had been made to modify textile and metal surfaces for bonding with rubber. The metal surfaces were modified using silane coupling agents and textile fibers were modified using plasma polymerization techniques. Some results on adhesion of metals to a range of sulfur-cured rubber compounds using a combination of organofunctional silanes are given here. The treatment was not only effective for high-sulfur compounds but also for low-sulfur com pounds as used in engine mounts and even for some semi-EV compounds. Coatings of plasmapolymerized pyrrole or acetylene were deposited on aramid and polyester tire cords. Standard pull-out force adhesion measurements were used to determine adhesion of tire cords to rubber compounds. The plasma coatings were characterized by various techniques and the performance results are explained in an interpenetrating network model.

• Textile Coloration and Finishing
• /
• v.29 no.2
• /
• pp.55-61
• /
• 2017

A non-fluorinated polystearyl methacrylate water repellent was synthesized by emulsion polymerization. The number and weight averaged molecular weights were obtained at around 137,277 and 237,754g/mole. The melting point was observed at $32^{\circ}C$. The contact angle of water droplet on fabrics treated with the water repellent was $140{\sim}145^{\circ}$ for cotton and polyester, and $125{\sim}130^{\circ}$ for wool and nylon. Since the critical surface tension was estimated at 20.7mN/m, even though relatively not so strong as fluorinated water repellent, it is considered to be used as a good water repellent practically.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1591-1597
• /
• 2012

Adherend samples were made from unsaturated polyester and woven and mat glass fibers by the hand layup and vacuum methods. The mechanical properties of the adhesive, composite adherends, and terminal-joint and secondary-joint specimens were determined experimentally. Combinations of the experiment results and the bonding theory were used in this study. The maximum and average shear stresses were calculated based on the maximum tensile force and geometry parameters of the joint specimens. The results of the maximum and average shear stresses were compared and evaluated for six joints. The results showed that the grinding and grind/acetone joint had the highest strength among three types of terminal-joints. Similarly, the mat-mat and mat-woven joints had the highest strength among three types of secondary-joints with the same value. Conversely, no treatment and woven-woven bonding had very low strength. In each case, failure occurred always at two ends and then moved toward the middle area of the overlap length.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.3 s.43
• /
• pp.335-344
• /
• 1992

This study was conducted to investigate the influence of addition of cetyl trimethyl ammo­nium bromide (CTAB), and amine [ethylamine (EA) or ethylene diamine (EDA)] to aqueous sodium hydroxide (NaOH) solution on polyester alkaline hydrolysis, The experimental vari­ables such as CTAB concentration, EA or EDA concentration, NaOH concentration, tempera­ture and time were compared, and the changes in physical and chemical properties of alkaline­hydrolyzed PET fabrics depending on their treated conditions were measured, The results are as follows: 1. By adding CTAB and amine in aqueous NaOH solution, increasing effect on weight loss of PET fabrics was obtained in simultaneous addition of CTAB and EDA, but not in CTAB and EA. 2. By adding CTAB & EDA simultaneously, increasing effect on weight loss was obtained regardless of EDA concentration, time and temperature, and it was more effective at lower NaOH concentration. :l. The increase of void space (or irregularly grooved surface), of softness, of wickability, of dyeability on PET fabric, and the decrease of tensile strength, of molecular weight were observed according to the weight loss on the PET fabrics. These changes were equal to all alkaline-hydrolyzed PET fabrics regardless of addition of CTAB and amine. l. There was little changes on crystallinity, thermal behavior when PET fiber was treated with ,aqueous NaOH solution with CTAB and EDA. These results supported that increasing effect on weight loss take place without inducing of fine structural change of PET fibers.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.1
• /
• pp.193-202
• /
• 2008

This paper investigates experimentally the confining effect, strengthening capacity and rebound rate of sprayed Fiber-Reinforced-Polymer (SFRP). From the method, resin and chopped fibers are sprayed separately from the nozzle with high pressure, and then they are attached to the concrete surface, so structure could be repaired. To evaluate the strengthening effect of sprayed FRP, cylindrical specimens and beam specimens were strengthening with SFRP. As main material of FRP, glass fiber and polyester resin are used. To investigate the optimum condition of sprayed FRP, the effects of fiber length, coating thickness, fiber volume ratio and concrete strength were examined. Capacities of sprayed FRP method were also compared to the FRP sheet method. In case of the sprayed FRP, rebound rate is important parameter considering economical efficiency and constructibility, so rebound rate of was discussed. From the test results, optimum conditions of sprayed FRP were determined. SFRP method showed superior strengthening capacities than FRP sheet method.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.894-899
• /
• 2012

In recent years, recycling process has come to be necessary for separating metals, glass fibers and polymer from WPCBs (waste printed circuit boards) due to an increasing amount of electronic device waste. In this study, dimethylformamide (DMF) and attrition mill reactor were used to separate the component such as metals, glass fiber and epoxy resin from WPCBs. Separation of glass fiber from WPCBs was carried out under stirring rates 300~600 revolution per minute (rpm) for 1~2 h as the various agitator. The recycled glass fibers (RGF) were analyzed by thermogravimetric analyzer (TGA) for degree of separation of epoxy resin in the WPCBs. The degree of separation of epoxy resin of WPCBs increased in attrition mill agitator as a mechanochemical process for recycling WPCBs. The RGF separated in the WPCBs was applied as a reinforcement in the RGF/unsaturated polyester composites to reuse as a reinforcement.

• The Research Journal of the Costume Culture
• /
• v.25 no.4
• /
• pp.448-457
• /
• 2017

This study aims to analyze the changes in the mechanical properties of interlock fabrics knitted with three types of fibers (i.e., cotton, wool, and polyester) by bonding fusible interlinings with varying deniers (i.e., 10D, 20D, and 30D) for a 3D virtual try-on system. We experimented with four properties and thicknesses of twelve specimens of interlining bonded knitted fabrics including face fabrics and interlinings. The results showed that the tensile property changed values (i.e., LT increased, and WT and RT decreased) according to the denier of interlinings; however, the change was slight. On the other hand, the bending property increased significantly as the denier of the interlining increased on both the wale and the course. Among shearing properties, the value of G increased as the denier of the interlining increased on both the wale and the weft; however, 2HG decreased. Additionally, changes in the compression property varied according to the fibers and the denier of the interlinings. The thickness of the knitted fabrics increased or decreased slightly by bonding the interlining. based on these results, we conclude that the 3D virtual system users need to reflect these numerical changes of interlock fabrics by bonding interlinings when they perform fitting tasks on the screen to accurately express the to accurately express the manufacturing conditions of the real garment.

• Textile Coloration and Finishing
• /
• v.27 no.3
• /
• pp.175-183
• /
• 2015

Weight loss treatment of a fiber leads an improvement of its handle and drape properties. Hydrolysis of a fiber is commonly known as a method to reduce its weight of 5-40%. Most of the studies on the weight loss treatment are mainly based on polyester fibers and there has been almost no study on the weight reduction of nylon fibers. In this study, however, in order to develop a use of nylon 6 fiber for the industrial applications such as toothbrush, underwear, carpet and more, weight loss treatment of a nylon 6 fiber was carried out. Under various treatment conditions, morphological analysis were done to observe the change in the structure of the surface and analysis. From the observation of formic acid treated nylon 6 fiber, there were many etched and deformed morphologies. Thermal and crystalline properties were analyzed to find the changes in the crystal structure caused by the weight loss treatment. There were little differences in the crystalline properties of nylon 6 fiber by formic acid treatment. Tensile strength of nylon 6 fiber decreases with acid concentration. The FITR peak intensity of the amide bond decreases with formic acid concentration.