• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.115-123
• /
• 2023

In this paper, we report and discuss the semi-permanently hydrophilic (SPH) treatment of polyester fabric using plasma polymerization and oxidation based on atmospheric pressure dielectric barrier discharge (APDBD) technology. SiO_xC_y(-H) was coated on polyester fabric using Hexamethylcyclotrisiloxane (HMCTSO) as a precursor, and then plasma oxidation was performed to change the upper layer of the thin film to SiO₂-like. The degradation of hydrophilicity of the SPH polyester fabrics was evaluated by water contact angle (WCA) and wicking time after repeated washing. The surface morphology of the coated yarns was observed with scanning electron microscopy, and the presence of the coating layer was confirmed by measuring the Si peak using energy dispersive x-ray spectroscopy. The WCA of the SPH polyester fabric increased to 50 degrees after 30 washes, but it was still hydrophilic compared to the untreated fabric. The decrease in hydrophilicity of the SPH fabric was due to peeling of the SiO_xC_y(-H) thin film coated on polyester yarns.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.8
• /
• pp.1057-1064
• /
• 2004

Silk, polyester, cotton, and wool fabrics were embroidered with varying stitch length of 3mm, 5mm, and 10mm to examine the difference in fabric shrinkage in terms of sewing direction, fabric thickness, cover factor, stitch length, and fiber type. Warp, filling, and bias direction of sewing resulted in no difference in fabric shrinkage. Within the samples with same stitch length, there was less fabric shrinkage in fabrics with higher fabric thickness or higher cover factor. There was larger shrinkage when sewn with longer stitch length. Comparing fabrics with different fiber types but similar fabric thickness, silk and polyester fabrics showed the smallest fabric shrinkage and wool fabrics showed the largest shrinkage. It is shown that similar fabric shrinkage between silk and polyester is due to the similarity in cover factor.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.103-114
• /
• 1973

Radiation grafting of acrylic acid and 4-vinylpyridine at room temperature has been studied by an impregnation method to improve the hygroscopic properties, the antistatic behavior and the dyeability of polyester fabric. Polyester fabric was impregnated with acrylic acid or aqueous emulsion of acrylic acid-4-vinylpyridine by immersion at 25$^{\circ}$or 7$0^{\circ}C$. The impregnated fabric was irradiated under nitrogen gas with ${\gamma}$-rays from Co-60. When acrylic acid grafted polyester fabric was treated with sodium carbonate, calcium acetate and potassium persulfate, tne rate of water absorption was increased and most parts of polyacrylic acid formed were extracted off from the fabric with 0.1% solution of sodium hydroxide at 10$0^{\circ}C$. In the case of the impregnation of a mixture of acrylic acid and 4-vinylpyridine the petcent of grafting has been shown to be proportional to the ratio of 4-VP/AA and radiation dost. Estimating by contact angle measurements of water on the various polymer surfaces, the antistatic behavior was decreased with the increase of grafting percent. The investigation of electron micrograph disclosed the existence of certain type of discontinuities in the acrylic acid grafted polyester fiber which was treated with various salts.

• Textile Coloration and Finishing
• /
• v.13 no.3
• /
• pp.180-187
• /
• 2001

Generally, polyester microfiber has much greater dye uptake than that of regular ones. In spite of high dye up-take visual shade depth of dyed fabric decreases with smaller denier, which results in poor washing fastness of dyed fabric. In this study, in order to investigate the washing fastness, polyester microfiber fabric was dyed by using two type of disperse dyes and treated with 3 different reduction clearing methods. The reduction clearing methods in this study are normal alkaline reduction clearing, $N_2$ gas replacement method, and ultrasonic treatment during reduction clearing. The results were as followings ; The most important factors affecting the washing fastness of polyester artificial suede fabric were found to be the reduction clearing method, the chemical structure of used disperse dyes and the structure and denier of fibers. It was also obtained that the heat treatment of dyed fabric decreased the washing fastness due to the dye migration from inner phase to surface.

• Textile Coloration and Finishing
• /
• v.18 no.5 s.90
• /
• pp.61-71
• /
• 2006

This paper addresses the factors hindering the image quality of lines in inkjet printed on polyester fabric as printing media. Lines were printed onto different types of polyester fabrics in warp and filling directions. Line image quality including line width, edge blurriness, and edge raggedness was assessed. The effect of capillary wicking on line image quality of printed spun polyester fabric is discussed. The factors on the image quality include printing position(top of the yam or between the yarn), printing direction(warp or filling), yarn structures(filament or spun), thread size(yam or fiber), finishing, and ink properties(evaporation rate). More than 30% differences in image quality results were observed by changing the printing location on the spun polyester fabric. The best results of the image quality were obtained with the printed plain and spun polyester fabrics. The fiber sizes may affect capillary size; therefore, the image quality can be dissimilar. Types of finishing materials and inks greatly improve the line image quality on spun polyester fabrics.

• Journal of Fashion Business
• /
• v.10 no.3
• /
• pp.23-30
• /
• 2006

Various high-touch textile products have been developed recently including ultra-fine denier filament yarn fabrics. The touch or hand of high value-added products is of prime importance. Physical and mechanical properties of fabric specimens, ultra-fine denier filament yarn fabric specimen, 100% wool fabric and wool/polyester 50:50 fabric,were measured using the KES. Compressibility of the ultra-fine denier fabric is recommendable, possibly due to the good bulk property of the specimen. Overall, the THV of the ultra-fine denier fabric is positioned between those of the 100% wool fabric and wool/polyester 50:50 fabric. Observed differences in the physical and mechanical properties explain the fabric specimen characteristics reasonably.

• Fashion & Textile Research Journal
• /
• v.7 no.1
• /
• pp.111-114
• /
• 2005

In this the study, polyester/cotton(P/C) blended fabrics with fine denier were developed to get the light weight compared with the traditional P/C blended fabrics. Moreover, the width of the fabrics was extended by the tenter during the final heat treatment to get the lower fabric density and lighter weight. Then, the physical properties of these fabrics were analysed. The results were as the follows: The developed fabrics had 22.6-31.6% lighter weight than the traditional fabrics with the same fabric width. The weight of fabric decreased drastically with the fabrics width down to 67.1 $g/m^2$. The fabric density for the warp direction decreased with the fabric width. The tenacity and the elongation of the developed fabrics was little lower than that of the traditional fabrics. The air permeability of the developed fabrics increased with that of the traditional fabrics. The stretch rate of the developed fabrics decreased with increasing the fabric width. Residual stretch rate of the developed fabrics was more stable than that of the traditional fabrics. Residual stretch rate of the developed fabrics increased with the fabric width, but the highest value was less than 5% which is quit stable.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.17 no.1
• /
• pp.151-161
• /
• 1993

The purpose of this study was to investigate the effect of hydrophilic finish for polyester (PET) fabric and hydrophobic finish for cotton fabric on the water transport and comfort properties. Polyester fabric was treated with 10% sodium hydroxide solution to impart hydrophilicity. Cotton fabric was sprayed with Scotch-gard$^{(R)}$ water and oil repellent finish to impart hydrophobicity. Porosity, air permeability, contact angle, wickability and water vapor transport rate (WVTR) were measured to determine the water transport properties of fabrics. To compare the comfort properties of treated and untreated fabrics, wear test was performed by putting fabric patches on the upper back: stratum corneum water content (SCWC), subjective wettedness and comfort rating were determined. The results were as follows: (1) The contact angle of water on treated polyester fabric was decreased and that of treated cotton fabric was increased. Also, the wickability of treated polyester fabric was increased and the wickability of cotton fabric was decreased. (2) Although each finish did not change porosity, the water vapor transport rate of treated polyester fabric was increased and that of treated cotton fabric was decreased slightly. (3) The results of stratum corneum water content measurements showed good agreement with the results of the contact angle and the wickability, i.e., the better the liquid water transport properties are, the less the stratum corneum water contents were resulted. (4) The realtionship of subjective wettedness or comfort and stratum corneum water content was independent. Therefore, it was concluded that human perception on the subjective wettedness or the comfort is affected by the skin contact of wet fabric rather than by the stratum corneum water content.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.2
• /
• pp.347-355
• /
• 2005

Biodegradability of cotton/polyester blend fabric was investigated employing activated sluge test, soil burial test and enzyme hydrolysis. Surface changes of the degraded sample were observed through a microscopy. Changes in X-ray diffraction patterns and crystallinity were examined using X-ray diffractometer. Experimental results revealed that biodegradability of cotton/polyester blend fabric was proportional to the blending ratio of cotton, not showing any synergy effect. Polyester 100% hardly degraded in this study. Through the comparison of the experimental method it was shown that the biodegradabilities determined from activated sludge test and enzymatic hydrolysis except soil burial test were linearly related to the blending ratio of cotton in the blent fabrics. It is probably because the biodegradability determined from the retention of tensile strength of fabrics buried in soil was affected by the stress distribution of polyesters throughout the fabric. From the microscopic observations it was revealed that fungi were grown on the fabric surface and the colors turned yellow, brown and black. X-ray diffraction patterns showed that the heights of crystalline peak coming from cotton part in blend fabrics decreased whereas those coming from polyester part increased comperatively as time passed by. Crystallinities of cotton 100% fabric increased slightly at the begining and then decreased continuously.

• Textile Coloration and Finishing
• /
• v.3 no.3
• /
• pp.6-14
• /
• 1991

To develop an one-bath process for weight-reduction and mercerization of polyester/cotton fabric, concentrated NaOH solution was padded and steam-treated at high temperature. Following results which can be used commercially are obtained. (1) Steaming temperature of 110-12$0^{\circ}C$ is most efficient. (2) Optimum concentration of NaOH solution is 15-20%. (3) Most favorable weight-reduction is 20% in the aspect of fabric handle, and under this treating condition, dye exhaustion onto the mercerized cotton fiber is also increased to 40% or more. From above results, we believe that the economical and concurrent weight-reduction and mercerzation of polyester/cotton fabric can be realized. Moreover, with continuous treatment by pad-steam procedure, it is expected that this is, also, advantageous for the improvement of fabric quality and productivity.