• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.05a
• /
• pp.123-123
• /
• 1998

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.10a
• /
• pp.86-88
• /
• 1997

• Applied Chemistry for Engineering
• /
• v.30 no.6
• /
• pp.698-706
• /
• 2019

Over the last few decades, there have been a lot of efforts to develop soft actuators, which can be external stimuli-responsive and applied to the human body. In order to fabricate medical soft actuators with a dynamic precision control, the 3D crosslinked poly(acrylic acid) (PAAc)/poly(vinyl alcohol) (PVA)/poly(ethylene glycol) (PEG) hydrogels were synthesized in this study by using a radiation technique without noxious chemical additives or initiators. After irradiation, all hydrogels showed high gel fraction over 75% and the ATR-FTIR spectra indicated that PAAc/PVA/PEG hydrogels were successfully synthesized. In addition, the gel fraction, equilibrium water content, and compressive strength were measured to determine the change in physical properties of PAAc/PVA/PEG hydrogels according to the irradiation dose and content ratio of constituents. As the irradiation dose and amount of poly(ethylene glycol) diacrylate (PEGDA) increased, the PAAc/PVA/PEG hydrogels showed a high crosslinking density and mechanical strength. It was also confirmed that PAAc/PVA/PEG hydrogels responded to electrical stimulation even at a low voltage of 3 V. The bending behavior of hydrogels under an electric field can be controlled by changing the crosslinking density, ionic group content, applied voltage, and ionic strength of swelling solution.

• Korean Chemical Engineering Research
• /
• v.55 no.6
• /
• pp.778-784
• /
• 2017

Membranes were prepared by incorporating Na-Y zeolite particles into poly(vinyl alcohol) (PVA) cross-linked with poly(acrylic acid) (PAA). The membrane was characterized by FT-IR spectroscopy, contact angle measurement, swelling test, SEM analysis, and XRD analysis. The pervaporation separation of water/acetic acid mixtures was carried out using prepared membranes. From the results, it was shown that the hydrophilic property of prepared membrane increased with increase of zeolite contents and the PVA/PAA membrane with zeolite addition showed higher permeation flux than that of without zeolite membrane. The PVA/PAA membrane containing 8 wt% zeolite showed the highest permeation flux and separation in the feed solution containing 10 wt% acetic acid.

• Restorative Dentistry and Endodontics
• /
• v.40 no.3
• /
• pp.216-222
• /
• 2015

Objectives: To evaluate the effects of copolymer of acrylic acid and maleic acid (Poly[AA-co-MA]) and calcium hypochlorite ($Ca(OCl)_2$) on root canal dentin using scanning electron microscope (SEM). Materials and Methods: Twenty-four single-rooted teeth were instrumented and the apical and coronal thirds of each root were removed, leaving the 5 mm middle thirds, which were then separated into two pieces longitudinally. The specimens were randomly divided into six groups and subjected to each irrigant for 5 min as follows: G1, $Ca(OCl)_2$; G2, Poly(AA-co-MA); G3, $Ca(OCl)_2$ + Poly(AA-co-MA); G4, sodium hypochlorite (NaOCl); G5, ethylenediaminetetraacetic acid (EDTA); G6, NaOCl+EDTA. The specimens were prepared for SEM evaluation. Smear layer, debris and erosion scores were recorded by two blinded examiners. One image from G3 was analyzed with energy dispersive spectroscopy (EDS) on suspicion of precipitate formation. Data were analyzed using the Kruskal-Wallis and Dunn tests. Results: G1 and G4 showed the presence of debris and smear layer and they were statistically different from G2, G3, G5 and G6 where debris and smear layer were totally removed (p < 0.05). In G1 and G4, erosion evaluation could not be done because of debris and smear layer. G2, G3 and G5 showed no erosion, and there was no significant difference between them. G6 showed severe erosion and was statistically different from G2, G3 and G5 (p < 0.05). EDS microanalysis showed the presence of Na, P, and Ca elements on the surface. Conclusions: Poly(AA-co-MA) is effective in removing the smear layer and debris without causing erosion either alone or with $Ca(OCl)_2$.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.208-215
• /
• 2012

Gel polymer electrolyte membranes were prepared from blends of polyvinyl alcohol (PVA) and poly (acrylic acid) (PAA), by solution-cast technique. The PAA content in the blend varied from 30 to 80 wt%. With the gel polymer electrolyte membranes, Zn air batteries were fabricated. The gel polymer electrolyte membranes were characterized by means of stress-strain test, impedance test. The Zn air batteries were tested by current interrupt method and galvanostatic discharge method. The tensile strength and tensile modulus decreased with increasing PAA content in the gel polymer electrolyte membrane. On the other hand, the ionic conductivity increased with increasing PAA content. The effect of ionic conductivity trend of the gel polymer electrolyte membrane in the Zn air battery was confirmed through current interrupt method and galvanostatic discharge method experiments. The battery with higher PAA content gel polymer electrolyte membrane showed lower IR drop and higher discharge capacity.

• Journal of Radiation Industry
• /
• v.6 no.2
• /
• pp.153-158
• /
• 2012

In this research, poly(acrylic acid) (PAAc) hydrogels containing zinc oxide particle were prepared by gamma-ray irradiation. PAAc powder was completely dissolved in distilled water at room temperature. Water-insoluble zinc oxide powder were added into the PAAc solution and stirred until totally dissolved. Finally, the mixture was irradiated by gamma-ray irradiation to make crosslinking. The effects of various parameters such as zinc ions' concentration, irradiation doses were varied and investigated in detail. PAAc hydrogels containing zinc oxide particle were characterized by gel content and swelling ratio. Moreover, the antibacterial properties of this material were evaluated by paper diffusion test against the Gram positive and Gram negative bacteria.

• Applied Chemistry for Engineering
• /
• v.5 no.4
• /
• pp.669-680
• /
• 1994

DMA-co-DAMA were synthesized from 2-diethylaminoethyl metacrylate and dodecyl-metacrylate containing long chain hydrocarbon group with hydrophilic and hydrophobic radicals. To facilitate water emulsification,acrylic copolymer was cationized by acetic acid to produce acetated acrylic copolymer. The structures of the synthesized copolymer and acetated copolymers were confirmed by IR, NMR, and molecular weight was measured by GPC, and C. H. N elemental analysis. Acetated acrylic copolymers were perfectly emulsified in water and showed increased emulsion stability. Polymer dispersion for cement modifier(PDCM-PDD) was prepared by blending of the guaternized acrylic copolymer synthesized above sodium silicate sodium gluconate oleic acid and triethanol amine. The result with prepared polymer dispersion of cement modfier was examined, and it was found that excellent waterproffing effect; Water permeability ratio is 0.44 under the water pressure of $100g/cm^2$ and 0.55 under $3kg/cm^2$, and water absorption ratio is 0.36~0.47 and 1.02 compressive strength ratio at mixed ratio of water/PDCM-PDD is 45 times.

• Polymer(Korea)
• /
• v.33 no.6
• /
• pp.615-619
• /
• 2009

Pd-POSS nanoparticles were produced from the reaction of palladium (II) acetate and octa(3-aminopropyl)octasilsesquioxane octahydrochloride (POSS-${NH_3}^+$) in methanol at room temperature. Pd-POSS nanoparticles with a mean diameter of 60-80 nm were the highly ordered spherical aggregates. In contrast, Pd nanoparticles with a size of 4.0 nm were obtained when POSS-${NH_3}^+$ was not introduced. Pd-POSS/PAA nanocomposites of Pd-POSS nanoparticles and poly(acrylic acid) (PAA) were fabricated by utilizing ionic interactions between positively charged Pd-POSS nanoparticles and negatively charged carboxylate groups of PAA. PAA was used as a cross-linker for the preparation of hybrid nanocomposites with the controlled organized structures of Pd-POSS nanoparticles. That is, the self-organization of Pd-POSS nanoparticles was formed into the shape of continuous lines by using PAA as a cross-linker. The composition, structure, surface morphology, and thermal stability of the Pd-POSS/PAA nanocomposites were studied by FE-SEM, AFM, TEM, FT-IR, and TGA.

• Macromolecular Research
• /
• v.14 no.5
• /
• pp.552-558
• /
• 2006

Biodegradable nanofibrous poly(L-lactic acid) (PLLA) scaffold was prepared by an electrospinning process for use in tissue regeneration. The nanofiber scaffold was treated with oxygen plasma and then simultaneously in situ grafted with hydrophilic acrylic acid (AA) to obtain PLLA-g-PAA. The fiber diameter, pore size, and porosity of the electrospun nanofibrous PLLA scaffold were estimated as $250\sim750nm,\;\sim30{\mu}m$, and 95%, respectively. The ultimate tensile strength was 1.7 MPa and the percent elongation at break was 120%. Although the physical and mechanical properties of the PLLA-g-PAA scaffold were comparable to those of the PLLA control, a significantly lower contact angle and significantly higher ratio of oxygen to carbon were notable on the PLLA-g-PAA surface. After the fibroblasts were cultured for up to 6 days, cell adhesion and proliferation were much improved on the nanofibrous PLLA-g-PAA scaffold than on either PLLA film or unmodified nanofibrous PLLA scaffold. The present work demonstrated that the applications of plasma treatment and hydrophilic AA grafting were effective to modify the surface of electrospun nanofibrous polymer scaffolds and that the altered surface characteristics significantly improved cell adhesion and proliferation.