• Journal of environmental and Sanitary engineering
• /
• v.13 no.1
• /
• pp.91-103
• /
• 1998

Design data for COD and nitrogen removal from wastewater were collected from Pilot's Multi-stage Bio-reactor. Hyraulic conditions and pollutant loadings were varied in order to optimize the biological and operational parameters. Pilot's experimental results summarize as followings. 1. T-N removal efficiency in the organic volumetric loading 0.2 kgCOD/m$^{3}$·d was obtained as maxium of 85% at internal recycle ratio 2.5 and in more ratio than this it was decreased. Organic removal efficiency was about 91% under the overall experimental conditions and not influenced by recycle ratio.. 2. Nitrification reaction was shown as maxium in the SCOD$_{cr}$/NH$^{+}$-N ratio of 6.5 and in more ratio than this it was decreased. Denitrification rate was the maxium as 85% in more than 7.5 of SCOD$_{cr}$/NO$_{x}$-N ratio and in the ratio over this ratio it becomes constant. 3. By utilizing an applied new model of Stover-Kincannon from Monod's kinetic model, concentration of T-N in the effluent according to flow quanity in the influent was estimated as 8.74 and -67.5 respectively. The formula for estimating T-N concentration of effluent was obtained like this: N$_e$=N$_0$(1- $\frac{8.74}{(QN$_0$/A)-67.05}$)

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.4
• /
• pp.66-77
• /
• 2003

Monitoring data from agricultural reservoirs throughout the country were analyzed to classify agricultural reservoirs according to physical characteristics and COD concentrations, and evaluate the relationships bet-ween water quality items. The physical and chemical data of total 498 reservoirs were analyzed from 1990 to 2001. Average COD, TP, TN, Chl-a, SS concentrations for the reservoirs and pollutant loadings from their watersheds were used for the analysis. It was possible that reservoirs were classified to 4 types using the relationships between the ratios of effective storage per water surface (ST/WS ratio) and COD concentrations. It is recommended that the improvement measures of polluted reservoirs should be performed as following order : integrated consolidation type (complex mechanism type) $\rightarrow$ watershed consolidation type $\rightarrow$ integrated consolidation type (external mechanism type) $\rightarrow$ in-lake consolidation type $\rightarrow$ conservation type and the depth (ST/WS ratio) of reservoir maintained over 5~6 m for water quality improvement. The decision coefficients ($r^2$) between Chl-a and other items (COD, T-P, SS, T-N) were 0.6915, 0.6732, 0.5327, 0.3352, respectively. Therefore, reservoir managers could evaluate the trophic state of reservoirs by COD concentrations.

• Journal of Environmental Impact Assessment
• /
• v.14 no.2
• /
• pp.63-73
• /
• 2005

This study was performed to characterize stormwater runoff of pollution material from nonpoint sources during rainfall in drainage basins of Hongjechun watershed, and to suggest management methods to control the first flush of nonpoint sources. We conducted 4 times of field surveys including 3 times of wet period and 1 times of dry period for 5 stations, which consist of 3 stations in main stream of Hongjechun and 1 station in tributaries of Sinyoungchun and Gukichun, respectively. The variation of pollutant concentrations in terms of BOD, COD, SS and TP was large depending on the flow rate of stormwater, while a little change of TN concentration was investigated. Depending on the rainfall event, the difference of flowrates, and runoff loadings was large, while the difference of those for dry wether period was not noticeable for various sub-basins. In the results of unit load calculation, the range of 153-277 kg/ha/yr for BOD, 222-422 kg/ha/yr for COD, 264-432 kg/ha/yr for SS, 40-70kg/ha/yr for TN, and 13-25 kg/ha/yr for TP was obtained for Hongjechun, Sinyoungchun, and Gukichun sub-basins. Compared with the previous studies, the result of this study was founded to be acceptable.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.448-448
• /
• 2012

농경지의 잔류비료나 농약 등의 비점오염원은 강수 또는 관개를 함에 따라 지표 및 지하 유출과 함께 거동함으로써 토양 내에 집적됨과 동시에 지하수 수질에도 영향을 미칠 수 있다. 특히, 최근 고부가가치 농산물 수요의 증가로 전국적으로 확대되고 있는 시설재배의 경우 노지재배와는 상이한 유출 및 침투 특성을 가지고 있음과 동시에 과다시비로 인한 오염원의 토양 내 집적이 심각한 수준이나, 이에 대한 연구가 미흡한 실정이다. 따라서 본 연구에서는 시설재배지와 관행재배 지역의 토양 내 비점오염원 오염부하량을 평가하고 지하침투 과정을 평가하기 위하여 시설재배지와 관행재배지의 비교 평가가 가능한 포장 및 광역단위 시험포장을 연구대상지역으로 선정하였다. 모니터링 대상지역에서 토양수, 토양수분, 관개량, 기상조건 등을 측정하기 위한 장비를 설치하여 비점 모니터링 시스템을 구축하였고, 한달에 두 번 모니터링을 통하여 자료 수집 체계를 확립하였다. 시설재배지 및 관행재배지 토양 및 토양수 수질 분석 결과, 시설재배지 내 영양물질 농도가 관행재배지와 비교하여 전반적으로 높았으며, 특히, 하부토층으로 내려갈수록 영양물질의 농도 및 편차가 크게 나타났다. 향후 본 시험포장에서의 지속적인 모니터링 및 샘플링을 통하여 시설재배지 토양내 비점오염원의 침투 과정을 분석할 수 있을 것으로 판단되며, 지하침투 영향 및 오염부하량 모델링 기초자료로 활용될 수 있을 것으로 판단된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.88-88
• /
• 2017

유역에서의 효율적인 수량 및 수질 관리를 위해서는 정확한 수문 구성요소에 대한 이해가 선행되어야 한다. 유출 수문곡선을 이용한 많은 연구가 수행되었음에도 불구하고 정확한 기저유출 산정에 관한 연구는 매우 제한적으로 수행되어 왔다. 수문학교과서에 수록된 다양한 기저유출 방법은 실제 장기 유출 수문곡선에 적용하는데 한계가 있으며, 유역의 다양한 유출특성을 반영할 수 없다. 따라서 본 연구에서는 USGS에서 개발한 기저유출 분리 모형와 SWAT BFlow, 그리고 WHAT 시스템에 특성에 대해서 분석하였으며, 이러한 모형을 이용한 기저유출 분석의 한계점을 제시하였다. 정확한 기저유출 분리를 위해서는 유역의 감수곡선 특성을 반영한 기저유출 분리가 이루어져야 하며, 주지하수 감수곡선처럼 유역 대표 감수 특성을 이용하기 보다는 유황이나 계절별 감수특성을 고려한 김수 특성 인자에 대한 연구가 필요하다. 이외에도 유역에서 기저유출로 인한 오염부하 특성을 NO3-N을 중심으로 분석하여 정확한 기저유출 산정의 중요성을 제시하였다. 이와 같이 기저유출과 같은 수문 구성 요소에 대한 정확한 이해 없이는 효율적인 수량 및 수질 관리가 어려울 것으로 판단된다.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.3
• /
• pp.407-417
• /
• 2011

Nowadays, the high land use, mainly used for urbanization, is affecting runoff loads of non-point pollutants to increase. According to this fact, increasing runoff loads seems like to appear that it contributes to high ratio of pollution loads in the whole the pollution loads and that this non-point source is the main cause of water becoming worse quality. Especially, concentrated pollutants on the impermeable roads run off to the public water bodies. Also the coefficient of runoff from roads is high with a fast velocity of runoff, which ends up with consequence that a lot of pollutants runoff happens when it is raining. Therefore it is very important project to evaluate the quantity of pollutant loads. In this study, I computed the pollutant loadings depending on time and rainfall to analyze characteristics of runoff while first flush storm water and evaluated the runoff time while first flush storm water and rainfall based on the change in curves on the graph. I also computed contribution ratio to identify its impact on water quality of stream. I realized that the management and treatment of first flush storm water effluents is very important for the management of road's non-point source pollutants because runoff loads of non-point source pollution are over the 80% of whole loads of stream. Also according to the evaluation of runoff loads of first flush storm water for SS, run off time was shown under the 30 minute and rainfall was shown under the 5mm which is less than 20% of whole rainfall. These are under 5mm which is regarded amount of first flush storm water by the Ministry of Environment and it is judged to be because run off by rainfall is very fast on impermeable roads. Also, run off time and rainfall of BOD is higher than SS. Therefore I realized that the management of non-point source should be managed and done differently depending on each material. Finally, the contribution ratio of pollutants loads by rainfall-runoff was shown SS 12.7%, BOD 12.7%, COD 15.9%, T-N 4.9%, T-P 8.9%, however, the pollutants loads flowing into the steam was shown 4.4%. This represents that the concentration of non-point pollutants is relatively higher and we should find the methodical management and should be concerned about non-point source for improvement on water quality of streams.

• Journal of Korea Spatial Information System Society
• /
• v.10 no.4
• /
• pp.77-88
• /
• 2008

There has been growing demands to manage the water quality of west coastal region due to the large scale urbanization along the coastal zone, the possibility of application of TMDL(Total Maximum Daily Loadings) to Han river, and the natural disaster such as oil spill incident in Taean, Chungnam. However, no system has been developed for such purposes. In this background, the demand of GIS based effective water quality management has been increased to monitor water quality environment and propose best management alternatives for Han river and Kyeonggi bay. This study mainly focused on the development of integrated water quality management system for Han river bas in and its estuary are a connected to Kyeonggi bay to support integrated water quality management and its plan. Integration was made based on GIS by spatial linking between water quality attributes and location information. A GIS DB was built to estimate the amount of generated and discharged water pollutants according to TMDL technical guide and it included input data to use two different water quality models--W ASP7 for Han river and EFDC for coastal area--to forecast water quality and to suggest BMP(Best management Practices). The results of BOD, TN, and TP from WASP7 were used as the input to run EFDC. Based on the study results, some critical areas which have relatively higher pollutant loadings were identified, and it was also identified that the locations discharging water pollutant loadings to river and seasonal factor affected water quality. And the relationship of water quality between river and its estuary area was quantitatively verified. The results showed that GIS based integrated system could be used as a tool for estimating status-quo of water quality and proposing economically effective BMPs to mitigate water pollution. Further studies need to be made for improving system's capabilities such as adding decision making function as well as cost-benefit analysis, etc. Also, the concrete methodology for water quality management using the system need to be developed.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.1
• /
• pp.104-110
• /
• 2006

Growth in population and urbanization has progressively increased the loadings of pollutants from non-point sources as well as point sources. Accordingly, release of contaminants from non-point sources, released with surface runoff of rainwater, is influenced by atmospheric phenomena, geology, and topography. This makes the control of non-point source difficult. Therefore, this study intends to reveal the characteristics of runoff and particle size distribution to observe the fundamental characteristics of runoff. Experiments were carried out at inner road of research center. Average concentration of runoff ranged from 26.8 to 126.4 mg/L for SS and $COD_{Cr}\;15.3{\sim}117.7mg/L,\;TN\;0.07{\sim}5.16mg/L,\;TP\;0.06{\sim}0.49mg/L$ and heavy metals $0.00{\sim}0.29mg/L$. First flush, indicated wash off of pollutant at first rain, was observed for all types of pollutants. Most pollutants revealed a very close correlation with SS ($R^2=0.93{\sim}0.99$). After analyzing characteristics of particle, particle was finer than that from previously examined data.

• Journal of Korean Society on Water Environment
• /
• v.23 no.6
• /
• pp.945-950
• /
• 2007

The stormwater runoff from paved area are highly polluted because of particulate materials as well as metals from various vehicular activities. The Division of Road Maintenance in Ministry of Construction and Transportation was recently developed the Guidelines of Environment-kindly Road Maintenance. It is actually requiring the BMP construction to control the nonpoint source pollution as based on the TMDL program. This research is carried out in order to define the characteristics of stormwater runoff from the toll-gate of highways since 2006, which is actually one of the main pollutant sources of paved areas. This monitoring is the first phase work for establishing the treatment facilities in the toll-gates. The one of the main characteristics from toll-gate runoff is the first flush phenomenon containing lots of sediments and metal compounds at the beginning of a storm event. Usually it is used to determine the size of treatment facilities and to calculate the reduced pollutant mass in the facility. The research results shows that the mean EMC vaules for heavy metals are determined to $274.3{\mu}g/L$ for Cd, $1,273.4{\mu}g/L$ for Cr, $1,822.0{\mu}g/L$ for Cu, $6,504.9{\mu}g/L$ for Fe, $14,930.3{\mu}g/L$ for Pb, and $714.1{\mu}g/L$ for Zn. Also the metal mass loadings from the toll-gates are calculated using EMC, watershed area and storm duration.

• Spatial Information Research
• /
• v.9 no.2
• /
• pp.291-307
• /
• 2001

In today's environmental engineering practice, many technologies such as GIS have been adopted to analyze chemical and biological process in water bodies and pollutants movements on the land surface. However, the linkage between spatially represented land surface pollutants and the in-stream processes has been relatively weak. This lack of continuity needs to develop a method in order to link the spatially-based pollutant source characterization with the water quality modeling. The objective of this thesis was to develop a two-way(forward and backward) link between ArcView GIS software and the USEPA water quality model, WASP5. This thesis includes a literature review, the determination of the point source and non-point source loadings from WASP5 modeling, and the linkage of a GIS with WASP5 model. The GIS and model linkage includes pre-processing of the input data within a GIS to provide necessary information for running a model in the forms of external input files. The model results has been post-processed and stored in the GIS database to be reviewed in a user defined form such as a chart, or a table. The interface developed from this study would provide efficient environment to support the easier decision making form water quality management.